Search Documents

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle's (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer's goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000

By Regina N. Tempel, Mae S. Gustin, Mark A. Engle

This study characterizes the hydrogeochemistry of groundwaters near opalite-hosted epithermal hot-spring type mercury deposits in the Ivanhoe mining district, Elko County, Nevada. Local groundwaters generally range from Ca-HCO3 to Ca-Mg-Na-SO4 type waters with background mercury concentrations ranging from 0.014 to 0.32 ug/l. Leaching experiments conducted on mineralized rocks, using typical water chemistries to represent local groundwaters, yield total mercury concentrations ranging from 6.3 ug/l to 27.4 ug/l after one year of reaction. Geochemical modeling indicates dissolved mercury is dominated by HgO(,) and that precipitation of quicksilver controls mercury concentrations to an upper limit of 63 ug/l.

Jan 1, 2000

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By V Kainulainen

Sandvik Tamrock Corp has developed an underground rock flow simulation tool OPTIMINEÖ which is a direct simulation tool for matching suitable technology in rock material flow for underground mine layouts and production requirements. The tool gives the possibility of determining intersections, limitations and critical points in the layout and working procedures at an early stage of a new mine/mining area planning process. The tool combines the supplier machine knowledge with operational know-how and mine environment. It can be used for identifying the effect of an individual incident such as the effect of one additional turn in a continuous loading cycle to the daily capacity. This paper discusses the way the OPTIMINEÖ simulation tool operates, the benefits and restrictions, and reviews how it simulates some example cases and how the mines benefit from the tool in maximising the performance and optimising the mobile fleet, scheduling work and fine-tuning the layout.

Jan 1, 2000

This paper is in two parts. The first part provides background to coal in New Zealand, information on Solid Energy the Company and details of the resources, mines and products of the company. This part of the paper is intended for people who have limited knowledge of the New Zealand coal scene. The second part of the paper focuses on developments underway in New Zealand and discusses planned or possible changes and opportunities. This paper was first presented at the Coaltrans Asia Conference in June 2000.

Jan 1, 2000

By R. T. Dec

A review is undertaken of existing mathematical models of compaction process in roll press. The example of plane-strain, plane-stress model is presented together with comparisons between computed and experimentally recorded pressure distribution in roll nip region. Next, the discrepancies between predicted and measured values are discussed and practical method based on experimental optimization of compaction process using laboratory roll press is proposed. Examples of the selection of optimum roll press operating parameters for calcium oxide fines, sodium chloride and iron oxide dust are presented to illustrate advantages of the method. Finally scale up procedure is discussed for estimating the performance of commercial size roll press based on the data collected on laboratory size equipment.

Jan 1, 2000

By S. M. Pickering, L. T. Gregg

Appraisal of industrial minerals beneath privately owned land requires a different approach and mindset from valuation of base and precious metals or energy minerals, and from valuation of government-owned mineral lands. First, is it the value of inground minerals or of mining rights that is being sought? Second, value to whom, the mining company, a potential investor, the mineral landowner, a lending institution, the property tax assessor, or a condemnor? Third, how should mineral value be apportioned between the land and mineral owner, and a mining company with limited years of lease-hold interest? These and many other questions must be addressed before a valuation method and Discount Rate are selected. For various reasons the Income Method is most often used, with Net Present Value calculations made for long term predicted mining income. Choice of an appropriate Discount Rate is critical.

Jan 1, 2000

By Robert Hopler

The literature of explosives and blasting consists of a great variety of printed materials. These materials include technical papers, books, and articles by individuals and organizations; manufacturer’s product catalogs and brochures; handbooks offering guidance for the field blaster; complete encyclopedias on the subjects, and short entries in general-interest encyclopedias; government publications; proceedings of organizations devoted to the subjects; magazines specific to the subjects; articles in general circulation magazines; and other miscellaneous sources. In short, there is a multitude of literature on the subject, some well indexed for retrieval, but most not. This presentation will be a broad-brush look at some of the most important or interesting literature on the subject, since in no way can all the various references be mentioned, much less covered in depth. To illustrate the presentation, interesting materials from the author’s collection will be shown.

Jan 1, 2000

By L. A. Obasi, C. Obasi

Investigations were carried out to determine the effects of changing metamorphic conditions on the formation of magnetite from the Itakpe iron ore deposit. Various magnetite grain sizes from ferruginous quartzites from different zones were determined and analyzed statistically. The results reflect the reaction of mineral individuals. In particular, the granulometry of magnetite changed with changes in the mineral formation conditions in the deposit and correlate with the mineralo-geochemical zones. This is interpreted as part of a readjustment of the mineral to the prevailing conditions. Because granulometry is a prebeneficiation parameter, this work will be, no doubt, of importance to the exploitation and beneficiation of the quartzites and rich ores.

Jan 1, 2000

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By Janice M. Zinck, W. F. Griffith

Four different high density sludge-type processes, Cominco HDS, Geco HDS, Tetra HDS Process and the Staged- neutralization process were studied for their effectiveness in treating a low strength Zn-Fe rich acidic drainage solution. Each proms was run continuously for at least two weeks after obtaining steady state conditions. The final effluent quality, lime consumption, sludge density, settleability, filterability, viscosity, neutralization potential, metal leachability, operating and capital costs were measured and evaluated for each process.

Jan 1, 2000

By K Lee, K Fernando, S Rayner

Copper-gold ores have been technically difficult and uneconomical to process due to high consumptions of cyanide. Many copper oxide and sulphide minerals react with cyanide to form copper cyanide complexes, partly contributing to the high level of weak-acid dissociable cyanide in the tailings which is normally experienced during the processing of copper-gold ores. The cost for detoxification, if required for treating these tailings, would further inhibit the development of these copper-gold resources unless the cyanide used for leaching was recovered. Several technologies have been proposed to process copper-gold ores, aiming to recover copper as a co-product and cyanide for recycling in conjunction with the leaching process. A critical review of these processes reveals that a pre-concentration stage (solvent extraction or resin ion exchange) is required. Cyanide is recovered by the conventional Acidification-Volatilisation-Regeneration technique in most cases. A critical evaluation is also provided on technical aspects related to the use of Vitrokele Technology and a newly developed Elutech process in processing copper-gold ores, in particular with its application at May Day Mine.

Jan 1, 2000

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By Hiroshi Maeta, Takao Kino, Hirota Osono, Kikuo Matsusaka, Azusa Shida

"Prior to refine an ultra-high purity material, it is necessary to estimate the surface cleanness of a base material. In this report, the cleaning method of a surface for refining of an ultra-high purity aluminum has been studied. Aluminum sample of 99.999% purity was p9lished mechanically and electrically and washed with various solvents. Surface composition and a depth profile near the surface were examined. Based on the experimental results, surface structure of an ultra-high purity aluminum was discussed.IntroductionRecently, studies on high purity metals have become of interest, and we have reported .various properties of an ultra- high purity aluminum1- 2)In order to purify a metal, it is necessary to clean a work area and to make vacuous as possible. So, we are studying the purification of aluminum by an ultra-high vacuum refining system and a zone refining system set up in a clean room with cleanliness class of 1000.Now, in order to avoid a mixing of impurities into the refining metal, a surface cleanness of a base metal is very important factor. The purity of the base aluminum used our work is 99.999%, but the surface state of the base aluminum is not clear. Aims in this work .are to investigate the surface state and to obtain the cleaning method of the base aluminum.Experimental procedureSamples used in this work were 99.9% (3N), 99.99%(4N) and 99.999% (SN) aluminum produced industrially and 99.9999% (6N) aluminum purified by us."

Jan 1, 2000

By M. Josick Comarmond, John J. Jeffery, John W. Bennett

Oxidation rates of sulfidic mine wastes measured at a range of size scales have been collected from a number of sources. The results suggest that well-designed laboratory columns, under controlled conditions, provide comparable information on oxidation rates to that obtained from field test piles. It has been found in the cases presented that laboratory measurements of oxidation rates of a particular material type can be applied with confidence to the same materials in the field. It is recommended that a further study be undertaken to measure the time-dependence of the oxidation rate for a range of particle sizes and different materials. This study would provide measurements against which models of oxidation rate as a function of time and particle size can be tested, to give confidence in the use of models to describe dump behaviour in the longer term.

Jan 1, 2000

By Thomas L. Vandergrift

With the inevitable expansion of homes, businesses, and infrastructure in coal mining regions, the potential for future subsidence above abandoned mines is of increasing concern. Of particular concern are areas underlain by room-and-pillar coal mines. Unlike areas above longwall mines, where total extraction causes subsidence in a predictable and timely manner, subsidence above room-and-pillar mines is difficult to predict and may be active for many decades. As part of a geotechnical assessment of a water pipeline replacement project, NSA Engineering recently performed an evaluation of tong-terns subsidence potential along the proposed alignment due to time¬dependent failure of underlying room-and-pillar workings. The alignment of the replacement pipeline closely follows an existing concrete pipeline, which lies 150 11 to 300 fl above workings that both pre- and post-date the pipeline. Annual surveys along the existing alignment indicate that some subsidence has occurred, primarily from partial pillaring performed in the early 1980's, but that this subsidence is not active. Using the boundary-clement code LAMODEL as the primary analysis tool, NSA followed a three-step approach to estimate future subsidence impacts on the replacement pipeline. First, historical information for the mine was compiled, allowing for calibration of models to actual field conditions. Then, numerical models of workings directly under and adjacent to the proposed alignment were nun, with model input parameters varied until resulting loading patterns matched historical data, and subsidence in the model approximated that measured along survey lines. Finally, time-dependent deterioration of coal pillars was simulated by decreasing the coal strength in the calibrated model until a realistic "worst-case" condition (stability of barriers, but Yielding of production pillars and pillar remnants) was attained. Subsidence from the previous calibrated model was then subtracted from that of the worst case model to estimate future subsidence and related ground movement parameters that slay occur along the proposed alignment. The replacement pipeline design, incorporating couplings capable of withstanding the ground movements predicted, is now being finalized.

Jan 1, 2000

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By A. Casuge, D. Lee, J. A. Finch, C. C. Sui

The adsorption of copper and lead und their subsequent xanthate uptake were compared at pH 3.0, 6.0 and 9.2 on both fresh and oxidized sphalerite. The extent of adsorption and the rate of adsorption were strongly dependent on pH, with the highest adsorption of Cu and Pb being at pH 9.2. In the presence of both Cu and Pb, Cu adsorption was enhanced and Pb adsorption was suppressed. The adsorption kinetics of Cu and Pb were characterized by two- and three-stage adsorption processes, respectively. The exchange ratio of Cu to Zn was about one and that of Ph to Zn was greater than one and varied with pH. The uptake of xarlthate on "activated" sphalerite was dependent on pH. The rnaximum uptake was found to be at pH 6.0 for Cu-activated sphalerite artd at pH 9.2 for Pb-activated sphalerite. A measure of "activation strength" based on inetal ion adsorption and xanthate uptake was introduced. The activation strength of Cu to Pb was about one at acidic pH, but it was higher at neutral (pH -6) and alkaline (pH -3) conditions. The oxidation of sphalerite decreased Pb and, especially, Cu adsorption and decreased xanthate uptake.

Jan 1, 2000

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000