Search Documents

By Yannick C. Beaudoin

Southern Explorer Ridge (SER) is an anomalously shallow, intermediate-rate spreading ridge located 200 kilometers off the west coast of Vancouver Island, Canada. It ranges in depth between 2600 m (deepest basins) and 1760 m (bathymetric minimum). At least 60 sulfide deposits are known to be associated with hydrothermal vent fields along the ridge. For the first time geological data, including deposit locations, collected from 15 marine expeditions to SER since 1983 have been assembled in a GIS format. GIS processing techniques were employed to plot the distribution of base metal concentrations for recovered sulfide samples. The highest base metal concentrations are found in the vicinity of the Magic Mountain site (main active vent field), and also proximal to a side scan sonar anomaly referred to as AGOR 171. Individual samples near these locations have yielded values as high as 29.3 wt\% Cu, 34.3 wt\% zinc, 0.97 wt\% Pb, 2.0 ppm gold, and 664 ppm silver. Sample paucity is the key limiting factor that prevents adequate assessment of the areas economic potential.

Jan 1, 2001

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001

By E. Iasillo, R. R. Carneiro

Independent of the method chosen to forecast production, an accurate method to project metal extraction is needed in order to accommodate leach cycles that exceed leach data on hand and thus be able to accurately forecast production. Metal extraction data must be developed for each ore type identified in the deposit in order to apply the correct rate of leaching when a specific ore is being treated. Curve fitting is used to model the rate of disengagement of metal into the pregnant solution. This paper provides a description of a curve fitting algorithm developed by Mr. John T. Bartlett, inventor of the METSIM™ process simulation program. A methodology is provided by which the metallurgical data developed is evaluated to determine if accurate projections may be made from the data. A criteria has been developed to help determine when a column experiment may be terminated.

Jan 1, 2001

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Lauren M. Roberts, Ralph R. Sacrison

The Meikle Mine uses long-hole open stoping and cut-and-fill methods with backfill as the primary ground support technique. The mine operates at 2,858 tonnes per day (3,150 tpd) and has sustained operation in excess of 3,175 tonnes per day (3,500 tpd). Consistent backfill production is critical in achieving these mining rates. The heart of the system is a 7.65 cubic meter (10-cyd) horizontal shaft ribbon mixer located 328 m (1,075 ft) underground. System control is through several PLC's, allowing for a high degree of automation and process flexibility. Aggregate feed is routed 257 m (842 A) through vertical drop pipes in the ventilation shaft, a rockbox, transfer raises, and then into either of two raisebored storage silos. The aggregate is crushed mine waste, nominally 70% 3.8 cm x 1.0 cm (1-1/2"x 3/8") and 30% -1.0 cm (- 3/8"). The binder is routed through a vertical borehole, surge bins, and transfer raises. The binder is a mixture of Type II cement and fly ash. Two primary manufactured fill designs are produced: a high strength mix for stopes which will be undercut; and a low strength mix for stopes with only rib exposure. The high strength target is 5.5 Mpa (800psi) unconfined compressive strength in test cylinders. The low strength target is 2.8 Mpa (400 psi). The systim has allowed consistent achievement of these targets, while experience has allowed reduced costs and increased efficiencies. Fill placement is through 6.1 cubic meter (8 cyd) LHD's dumping into stopes. Specific sills and cut-and-fill drifts are jammed to the back. System enhancements have included colloidal mixers for cemented waste slurry placement and transfer raises for sending manufactured fill to the lower levels of the mine.

Jan 1, 2001

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Francois Reizine

Infrared sensors will include scanning detectors and positioning sensors. The focus will be on 1, 2, and 4-color wavelength pyrometer systems which allow the accurate measurement of emissivity and, consequently, of the true temperature even in the presence of scale, slag, and fumes. Such sensors are being used in blast furnaces, BOF's, and galvanizing lines. Laser sensors will be presented using different principles of physics, mainly time-of-flight, pulsed infrared lasers for level measurement and dimensional measurement; triangulation lasers for width and thickness measurements; and laser Doppler velocimeters for velocity and length measurements, including mass flow, elongation, and tension control, cut-to-length applications. These sensors and systems are based on state-of-the-art technical developments to improve productivity and quality and reduce maintenance and downtime.

Jan 1, 2001

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By Val Ness, Leonard Harris

Mentoring is defined as close counseling by an experienced and objective advisor within the industry. It is one aspect of attracting the best candidates into the minerals industry, holding their interest, and encouraging stable career growth. By encouraging proper mentoring practices, we foster strong careers, we transmit important wisdom to the next generation, we fortify the industry with better talent, and we encourage the best possible advocates for the minerals industry. This paper illustrates the consequences of poor mentoring, offers an example of positive mentoring practice at the college or university level, reviews some guidelines for stable and fruitful mentoring, and proposes a plan to spread appropriate mentoring practices. Authors' note: The use of masculine pronouns is for convenience and simplicity only. Our best engineers and managers come from both genders, and the authors intend no slight to either one.

Jan 1, 2001

In today?s high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accurate but flexible design thereby allowing operational managers to provide alternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different, with falling prices and escalating costs, improved margins become the focal objective. There are many ways to achieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the NPV of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

By Igor E. Mikhaltsev

This paper concerns the continuation of work on the deepwater non-oxygen cycle heat energy generating systems. The 25-kW prototype of a universal deepwater turbine-electric energy source with hydrazine-hydrate as the primary heat production chemical is described in short and its abilities are discussed. The ?hydrazine-hydrate 64? is a catalytically dissociated heat production chemical (H2H4 ? nH2O) with 36% of water. The system was designed for work in any depths of the ocean down to 6000 m. It was built and tested working in the testing chamber in the ambient hydrostatic pressure of 600 bar. Then it was tested in the autonomous programmed regime in the Atlantic Ocean. The privileges of that energy system for any bottom installations or moving devices designed for ocean mining which need high power energy sources (20-100 kW and more) are discussed. The important needed step forward is raising the efficiency of the system which needs some investigation work in known directions. It is supposed that the possibility of getting about 5 kg/kWh with improved battery charging possibilities could be achieved. This might make the system even more profitable for mining operations.

Jan 1, 2001

By W. G. Davenport

Chapter 10 showed that any given smelting task, e.g. production of 65% Cu matte, 1500 K, from CuFeS2, can be done with many different combinations of: blast%02 hydrocarbon fuel blast temperature. This chapter repeats the Chapter 10 calculations but reports the results in terms of the mass industrial oxygen mass hydrocarbon fuel blast preheat energy combinations that will produce 65% Cu matte, 1500 K, from CuFeS2 concentrate. It also determines the energy inputs equivalent to these combinations.

Jan 1, 2001

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By Anthony G. Grice

This paper discusses the contribution that backfill is making to the Australian mining industry and provides some information on the largest operations together with some novel applications. Each of the three major backfill types; hydraulic, rock and paste are discussed in turn with a focus on new ideas and advances in understanding, technology and operating practices.

Jan 1, 2001

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Bruce D. Hansen

The complexity of large geographically diverse or multicommodity mining companies requires a corporate structure, which provides the maximum long-term effectiveness. Structure models exist along the spectrum of centralization to decentralization. This paper examines the trade-offs of flexibility, cost, decision making, consistent strategies, and corporate control associated with different structural models as applied to mining companies. The mining industry typically lends itself to a business unit model. However, the degree of decentralization depends on size, proximal operations, technical complexity, product mix, geographic spread, mining methods employed, and the inherent capabilities of an organization.

Jan 1, 2001

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By G. H. K. Pearse, R. P. Taylor

The Big Whopper, one of only four giant economic rare metal pegmatites worldwide, is set to become a producer of the highly valued lithium mineral petalite (LiAlSi4O10) used in glass, ceramics and the specialty glass-ceramics familiar as Corningware® and the new ceramic stovetops. The deposit has a strike length of 1.5 km, a width of up to 80 m and a resource, open in all directions, of 11.6 Mt, grading 25% petalite. It is amenable to open pit mining and Avalon Ventures Ltd. holds a patent on a flotation process that produces an exceptional quality petalite product. The project will also produce: superb quality Na-feldspar which, too, finds use in glass and ceramics; the unusual Rb- K-feldspar for high voltage porcelain insulators; tantalum, in high demand for electronics; lepidolite, an ore of rubidium; and mica and tin. A positive prefeasibility study has been completed and it remains only to undertake bulk sampling and a full feasibility study.

Jan 1, 2001

By J. Litsenberger, T. E. Marshall, L. Burke, R. Melville, A. T. Iannacchione

Excessive levels of horizontal stresses cause ground fall hazards in underground mines in the Appalachian Basin. At an underground stone mine in Pennsylvania, a modified stress control mine layout is reducing the hazardous conditions associated with excessive horizontal stresses. A microseismic monitoring system is in place to measure levels of rock stability and provide information on the effectiveness of the design technique. The microseismic data is supplemented with frequent and extensive mapping of roof falls and roof rock damage. Findings to date show that the stress control layout provides more stable conditions and thus a safer environment for the mine workers.

Jan 1, 2001

By David Willock, S. Singh, Michael Glogger

The efficiency of the loading system in a mine depends upon the characteristics of the muck pile, the loading machine specifications and the loading practices. The focus of this paper was to look specifically at the size distribution of blasted material, and to quantify its effects on loader productivity. A scale model of LHD was designed and fabricated to represent machines currently employed in the industry. The experiments were performed using crushed Gabbro, which was mixed in various proportions according to Rossin-Rammler size distribution to give five different characteristic particle sizes and five different size distribution constants for each characteristic particle size. The effect of the size distribution constant on peak and mean penetration forces, work done and bucket fill factor was examined. In addition, the influence of mean particle size, 80% passing size (D80) and % oversize on the penetration force and bucket load was investigated.

Jan 1, 2001