Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By A. Bothma

The Impala No. 1A ventilation shaft is located approximately 15 kms north of Rustenburg and is accessed via the R510road from Rustenburg to Northam/Thabazimbi. This situation is shown on the location plan in Figure 1. The geology at the site consists of an upper layer of black turf of about 1 metre in thickness, grading into weathered norite. The depth of weathering is generally less than 5 metres. Zones of deeper weathering may occur along fracture zones associated with faults and dykes. Groundwater occurs mainly within the weathered/fractured aquifer system. The ventilation shaft is a 5.1 m diameter upcast shaft ,and forms part of a system of ventilation shafts to complement the existing infrastructure as mining progresses down the new twin decline extension of Impala 1 shaft. The principal reason for these shafts is to lessen the risk of an extended RAW and also to counter the effects of the heat build-up as the mining goes deeper, with the resultant effect that the existing cooling centre (fridge plant) becomes more remote from activities. The No. 1A shaft (upcast) is positioned approximately 1,2 km on down dip from the main shaft and the No. 1Bshaft (downcast) approximately 1,2 km further. Geological information was used from a borehole 1,2 km away on strike from the upcast shaft. The first shaft (1A) is a 5,1 m diameter hole to be fitted with two 2,2 MW fans, whilst the second shaft (1B) is 4,1 m diameter to accommodate a 7MW fridge plant.

Jan 1, 2001

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By H. Bilgin, Sedat Esen

In this paper, the ground vibrations induced by blasting for stripping work at Sekkoy Open Cast Coal Mine belonging to TKI Yenikoy Lignite Mine (YLI) are investigated and the procedures for monitoring and control of ground vibrations are presented. Ground vibration measurements are conducted in the direction of Turkish Electricity Authorities’ Yenikoy Establishment and social facilities because of the complaints and annoyance arising from this site. Forty ground vibration records are taken in this direction and the vibrations are measured in transverse, vertical, longitudinal components together with peak vector sum. After then the scaled distance relationship is determined at 95% confidence value. Further, Fast Fourier Transform analyses are carried out to determine dominant frequencies for both ground and the structures and amplification factors. When the records taken at four different structures together with the ground are evaluated, it is observed that one of the apartment buildings is amplified the amplitude of longitudinal component 4.3 times. The maximum allowable amount of explosive that can be fired safely at this mine is calculated and recommended on. In the determination of safe amount, 95% confidence line, USBM RI8507 and OSMRE criteria, the dominant frequencies of both ground and the structure, amplification factor and the human response are taken into account.

Jan 1, 2001

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

By B. Erik Ydstie, Dimitrios I. Gerogiorgis, Sridhar S. Seetharaman

"Carbothermic production of aluminium is an important alternative to electrolytic processes and has in fact been identified several decades ago as a potentially feasible and profitable process. The cornerstone principle is to take advantage of the endothermic reduction reaction between carbon and alumina instead of resorting to extreme amounts of electric energy to ionize and reduce aluminium oxide to aluminium. Electric energy is necessary only for heating purposes.The present study focuses on constructing and solving a steady-state electrothermic model for obtaining the spatial distributions for electric potential, electric field intensity and temperature. The complex issues of reaction kinetics and multiphase flow are handled by an approximation and are not addressed at the present stage, due to the lack of complete validated models. Because of its inherent complexity, the reaction slag is considered a pseudohomogeneous layer.An electrothermic simulation encompasses important research challenges, due to the limited knowledge of thermophysical properties for high-temperature multi component molten slags. Therefore, thermophysical property modeling and a systematic compilation of published data is a necessary and major first step towards enhancing understanding of the process fundamentals. Models are obtained by analyzing measurement data from numerous literature references for the density, viscosity, thermal and electrical conductivity and specific heat capacity of the slag.The electric potential, field intensity and temperature distributions obtained reveal interesting maxima which indicate localized superheating and lead to important engineering conclusions. The temperature profile calculated will serve as the foundation for the flow problem solution. This computational study will form a basis for future research towards combining the scopes of microscale CFD modeling and mesoscale process modeling into a unified modeling approach."

Jan 1, 2001

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By A A. Struthers, A D. Farmer

Power ultrasound may be applied to enhancing the processing of minerals. The enhanced performance is achieved through the very localised high-energy release at the mineral surface from the collapse of cavitation bubbles produced by power ultrasound. This gives rise to two effects: initially, the rapid cleaning of mineral surfaces û of oxidation products and coatings of fine adhering gangue minerals û and the attenuation of the boundary layer at the mineral surface during leaching, which allows fresh leachant to contact the surface more readily. Work carried out at CSIRO in conjunction with Tiwest Joint Venture has demonstrated that it is feasible to apply ultrasound to the leaching process in order to enhance the removal of contaminating minerals. When applied to the production of synthetic rutile from reduced ilmenite produced by the Becher process, the use of ultrasound proved beneficial to both the aeration and the final acid leach process. The effect of ultrasound was less marked in the case of the aeration process, once the method of introducing and dispersing the air was optimised. In the subsequent acid leaching step of the Becher process it was found that the application of power ultrasound could reduce leaching time to about one quarter of the time required when only agitation was employed. Projected capital and operating costs, based on currently available commercial equipment, are also presented, and indicate that the use of ultrasound is commercially as well as technically feasible.

Jan 1, 2001

By Karl H. Brandt

In the Auguste Victoria mine a bolted rectangular roadway has been kept open for the first time in the seam D/C after retreat. The target of the project was to gain a basis for planning and experience for future mining layouts in the same scam in view of the reuse of boated rectangular roadways. For this the roadway was additionally secured in sections with longbolts before the influence of the retreating panel had taken place. On retreat a concrete sidepack was concurrently put in place on the face side. The installed monitoring systems consisted of endoscopic devices, multiple extensometers (Tell-Tales), shear-tales, extensometers and convergence measurements. The experience that was gained was carried over into a physical and numerical model.

Jan 1, 2001

By Ali Porbaha

Rapid growth in the urban development requires continuous search for innovative technologies to construct complex infrastructure systems. Deep mixing is one promising construction technology that has a wide spectrum of applications for development and expansion of complex urban facilities. Large number of reported case history of the projects in Europe, Japan, and the US demonstrate the versatility of the technology compared to conventional methods of ground modification. A large number of factors influence the quality of the soil cement columns; some of these are rooted in the installation process and the effective use of machinery during construction. This paper attempts to present some issues related to installation of deep mixing that affect quality of the treated columns. Presented here are various installation patterns, installation machinery, installation sequence, effect of penetration/withdrawal injection methods, penetration/withdrawal speed, effect of number of shafts, rotation of the blade, shape and orientation of mixing tools, and rotational speed of the shaft on quality of the treated ground.

Jan 1, 2001

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

By Vianey Garcia-Osorio

One of the problems in the carbothermic aluminum process is the substantial loss of aluminum compounds as vapors due to the high temperatures in the process. In order to solve this problem a Vapor Recovery Unit (VRU) is proposed. In this unit operation the aluminum vapor undergoes a series of heterogeneous non-catalytic reactions forming solid, liquid and gas products. In this work a model for the simulation of this unit was developed which includes heat and material balances as well as heterogeneous non-catalytic reactions. The model leads to a system of differential equations; its solution was implemented in Matlab giving as a result a stage-by- stage solid-fluid reaction model.

Jan 1, 2001

By Alexander Malahoff

The study of why and how life survives in the Extreme environment is a major frontier of science today. Extremophiles are organisms that require extreme environment including high temperature, pH, pressure and salt concentration, or low temperature, pH, nutrient concentration, or water availability. Their common habitats are geothermal vents, pools, lakes and craters of active volcanic regions, such as those of New Zealand, Japan, Kamchatka, Yellowstone USA or the hydrothermal vents of the ocean ridges and submarine volcanoes. These settings are accessible by foot, boat, helicopter, or submersibles. This presentation examines the geology, chemistry of geothermal sites of New Zealand, including the active volcano, White Island, Yellowstone, the submarine volcano Loihi in Hawaii, and sections of the mid-ocean ridges. Designing process and construction of Extremophilic sampling and bioreactor systems used in the study of Extremophiles will be discussed. The driving force behind the research of extremophiles is not only the fundamental science, but also biotechnological potential associated with these microorganisms and their cellular products. The University of Hawaii?s Marine Bioproducts and Engineering Center (MarBEC) is laying the foundations for such new industries.

Jan 1, 2001

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By Ho-Jung Shin

The influence of cooling rate from 1873 to 1473 K on the size and morphology of austenite grains was studied using a Fe-O.I5 % C-I.5 % Mn alloy. The experiments were carried out at three different cooling rates of O.33KJsec, O.67KJsec and air-cooling. The austenite grain showed an isotropy at 0.33KJsec but maximized anisotropy at O.67KJsec and become much less. anisotropic. In order to account for these phenomena, a model was developed for estimating the size and morphology of austenite grains as a function of cooling rate. The driving force for the )( phase formation from 0 phase is caused by undercooling degree due to cooling rate and energy barrier is restricted to the misfit strain energy which is caused by mismatch between )( phase and 0 phase. The )( phase from 0 phase could be formed on not random orientation index systems but specific orientation systems depending on cooling rate.

Jan 1, 2001

By D Stow, M Edmondson

Lemington coal mine is operating in an environmentally sensitive area in the Hunter Valley, NSW, Australia. Late in 1999 the southern pit was developed using a series of box cut blasts. After the initial development the area would have been free dug due to the soft, well-jointed nature of the deposit. However, it was decided to trial drill and blast to determine if shovel productivity could be improved to enable an overall mining cost reduction. The initial trial blast results were less than satisfactory with both environmental issues occurring and the desired shovel productivity not being achieved. An audit of the blasts indicated that wet ground and the presence of soft clay inter-bedded with harder rock caused the poor blast results. Also, water-affected explosive product combined with explosive energy loss into soft ground led to flat spots and tight digging in the hard band areas, resulting in the lower dig rates. Lemington Mine and Orica Explosives developed a plan to match the rock with the appropriate explosive type and energy. This resulted in a number of blasts over a six-month period using a new non fuming explosive product, æNovaliteÆ. The results have been excellent with the environmental issues being totally resolved and dig rates improved, enabling reductions in mining costs. This has allowed the mine to continue with their exemplary record of environmental management whilst achieving operational efficiencies.

Jan 1, 2001

By J. Wallace Gwynn

Salt from Great Salt Lake was probably used by the Native Americans prior to the Jim Bridger Expedition to the lake in 1824-25, and was used by the region's early explorers and trappers after that time. From the arrival of the Mormon pioneers in 1847, salt has been produced from Great Salt Lake, starting first with the collection of crude salt from along its shores, and later by boiling down the lake's brine to obtain crystalline salt. Since these early beginnings, salt production from the lake has become a substantial commercial enterprise. Since the early 1960s, research and development have led to the economic production of potassium sulfate, magnesium metal, chlorine gas, magnesium chloride products, and nutritional supplements. Many of the salt-production techniques and equipment that were developed prior to 1964 are still being used today. Sodium sulfate has been produced, but is no longer marketed. Morton Salt, Cargill Salt, and IMC Salt currently extract sodium chloride, which is precipitated during the early stages of evaporation when the brine concentration reaches saturation, or about 26 to 27 percent total dissolved solids. Magnesium Corporation of America produces magnesium metal and chlorine gas, and IMC Kalium Ogden Corporation produces potassium sulfate, as well as magnesium chloride brine and flake products. These salt, gaseous, and metallic products are processed from the sodium-chloride-saturated, high-magnesium-chloride brines, and from the potassium and magnesium salts that are precipitated from the lake brine after it has been further concentrated. One obstacle to salt production is the fluctuating level of Great Salt Lake. In 1983, the lake level began a dramatic rise from an elevation of 4,200 feet (1,280.16 m) to its historic high of 4.211.85 feet (1,283.77 m) in 1986-87 (uncorrected USGS provisional lake-level records). The State of Utah employed flood-control measures, including breaching the Southern Pacific Railroad causeway in 1984, and pumping lake water to a shallow basin west of the lake in 1987. During the high-water years, the lake's mineral-extraction industries faced many challenges including the need to raise dikes to prevent flooding of facilities, broken dikes which resulted in the inundation of solar ponds, and dealing with the lake's greatly reduced brine salinities which resulted in lower annual salt and concentrated-brine production. The years following the record-high lake levels have been a time of adaptation, innovation, and change for Great Salt Lake industries. After its solar ponds were flooded in 1986, AMAX, Inc. built a new solar-pond complex near Knolls, and used the concentrated brines from the West Pond, generated by the State's West Desert Pumping Project. Great Salt Lake Minerals built a 21-mile-long (33.8 km) open, underwater canal, called the Behrens Trench, to convey concentrated brines from a new, remote solar pond on the west side of the lake to the east side of the lake, to help increase its production of sulfate-of-potash. There were also numerous changes in corporate ownership and production-facility locations.

Jan 1, 2001