Search Documents

By Franco Oboni, Iain G. Bruce

The design of tailings containment structures relies on well-understood engineering methods being applied consistently. Unfortunately, not all facilities are designed or managed to the same level of competency. To standardize procedures, the Mining Association of Canada (MAC, 1998) prepared a “Guide to Tailings Management.” It recommended review of designs and an assessment of the risks associated with tailings impoundments be implemented during all phases of amine life. This paper describes how the quantitative risk assessment (QRA) process can be used to define risks associated with the design, construction and operation of a tailings management facility. And it discusses how, once the risk tolerability curves (RTC) are defined for a project, they can assist the risk management (RM) process.

Jan 1, 2002

By Jens Kristen Laursen

In 1999, Molymex S.A. de C.V. (Molymex), Mexico. (a company wholly owned by Molibdenos y Metales S.A. (Molymet), Chile) decided to install the Haldor Topsrae Wet gas Sulphuric Aicd (WSA) process for cleaning of the 4-5% SO2 off-gas from their molybdenum sulphide master in Cumpas, Mexico to produce sulphuric acid. The decision to install a WSA plant was based on the successful operation of a WSA plant at Molymet's molybdenum sulphide roaster in Santiago, Chile since 1993. This paper describes the process layout of the Cumpas plant, the operating experience of the Santiago plant, and the, differences in. process design between the two plants. It will furthermore summarise the applications of the WSA process for other roasting plants and smelters within the non-ferrous. metals industry producing metals such as copper, lead, and molybdenum.

Jan 1, 2002

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By Michael J. Pyrcz, Clayton V. Deutsch

Strategic project decisions are based on the distributions global variables, for example, total mineable resource, or recoverable oil volume. These global variables distributions are very sensitive to the input one point statistic, that is, histogram and rock type proportions. Representivity in the one point statistic retains significance in all spatial models. Spatial sampling bias and nonrepresentative sampling complicate this process of building representative one point statistics. This work outlines the cause of bias, the inability of standard declustering to correct for this bias and two methods for correcting bias in the one point statistics: "trend modeling for debiasing" and "debiasing by qualitative data". An example is presented of each technique based on a poly metallic data set.

Jan 1, 2002

By T. Grammatikopoulos, A. McKen, O. Christiansen

Vanadium mineralization occurs in oxide-rich horizons within layered metagabbro zones of the Sinarsuk deposit, West Greenland. The main oxide minerals are vanadiferous magnetite and ilmenite, comprising 30% to 90% of the rock volume and the ratio of magnetite to ilmenite ranges from 3:2 to 4:1. Ore microscopy shows that magnetite and ilmenite vary between 0.2 mm and 4.5 mm in grain size, but locally they are coarser grained. Grains are subhedral to euhedral and annealed suggesting that they will liberate very well upon grinding. Electron microprobe analyses indicate that magnetite grains are homogeneous and have a vanadium content, in different mineralized samples, ranging from 1.93 wt% to 2.68 wt% equivalent V2O5. Ilmenite hosts abundant and variably sized hematite lamellae, and it has vanadium contents ranging from 0.32 wt% to 0.59 wt% equivalent V2O5. Preliminary beneficiation of two composite bulk samples shows the samples can be beneficiated fairly easily using low-intensity magnetic separation at a coarse grind (106 microns to 600 microns) to yield a vanadiferous magnetite concentrate. The presence of hematite lamellae in ilmenite prevents recovery of a satisfactory ilmenite concentrate. The most likely beneficiation flowsheet would encompass a primary mill (SAG or rod mill), which would grind to about 600 microns, followed by a rougher magnetic separation stage. The rougher magnetic concentrate would be reground in a ball mill until suitable liberation is achieved. The reground material would then be cleaned in further LIMS stages. However, further laboratory testing is required to establish the final beneficiation program. This work demonstrates the value of mineralogical investigation in guiding and explaining the results of beneficiation processes.

Jan 1, 2002

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By D. Anthony, R. A. Williams, R. Raponi

Barrick Gold Corporation in conjunction with SNC Lavalin Engineers and Constructors have developed basic engineering design for counter current decantation thickener (CCD) plants capable of processing 44 000 t/d. To achieve this throughput in a single train, the largest high-rate thickeners installed to date have been utilized in concert with large process slurry and solution transport systems. Process reliability and plant operability and maintainability have been carefully considered in order to develop a practical, yet cost effective design. The design also incorporates the challenges associated with installation of large equipment and structures in a remote location, with a climatically hostile environment, situated in a high seismic activity zone.

Jan 1, 2002

I have headed this paper with a question and for the impatient among you ûthe answer is no we have not run out of developments but, and it is a big æbutÆ, we need to be innovative and ahead of the game or ænoÆ will be æyesÆ before we know it.Why do I believe that our future lies in innovation? Thirty years ago, knowledge doubled every 14 years. It is now doubling every seven years. In 1965, Gordon Moore, one of the founders of the chip maker Intel, made an observation that growth in memory chip performance is doubled every 18 months which became known as MooreÆs Law. Now there is fibre law, where the transmission line capacity doubles every nine months and storage capacity, under disc law, doubles every 12 months. What does this mean? Well, firstly there is a massive rise in information flow and availability with no limits in growth for at least the next ten years. Secondly, unlike our grandfathers, we are most unlikely to be employed by the same firm for our working career - we may not even have the choice to stay with the same company. In a phenomenon Richard Foster and Sarah Kaplan (2001), borrowing from Schumpeter, termed æcreative destructionÆ, companies are unable to sustain market-beating levels of performance for more than ten to 15 years. In the 1920s the turnover rate of companies in the United States was 1.5 per cent, so a company could employ almost three generations from the one family. A company had a half life of 60 years. In other words, you could well be in the same working environment as your grandparents. Today the churn rate is estimated to be eight to ten per cent. A company has a half life of five to six years. So for large companies, as an employer or employee or as a contractor, your working environment has a 50 per cent chance of changing in five years. Innovation is the driver of this rapid rate of change. Innovation is not for the faint hearted (Cutler, 2001) but it is the core for success in the global economy. The rate of change in our world is not going to decrease. We must learn, not only to manage change, but to enjoy the process of changing û to ride the tsunami of the knowledge economy.

Jan 1, 2002

By P. Bousquet

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian mining industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (e.g., pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2002

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By K Osman, P Bennett

The mining of an underground orebody requires development both in waste and ore before stoping commences. Regardless of what metal is being extracted, the waste development is minimised to reduce the cost per unit of metal mined. At the Western Metals Zinc Kapok mine site, reducing the cost per tonne of lead and zinc mined is paramount. Decline waste development costs can be minimised by methods such as increased gradient or reduced drive size. Ore development will also involve some mining of waste. The degree to which waste mining can be minimised will depend on the thickness and dip of the orebody. The drive geometry will also determine the percentage of waste within the face. It is by mining methods such as resue mining that selective mining may be used to maximise the amount of metal mined and reduce waste dilution. Resue mining can be used around a set of selection criteria established by the mine site. These selection criteria will determine how resue mining can be applied to the mine site. Selection criteria include firing times, number of headings available, acceptance criteria for percentage lost metal, dilution and most importantly operator acceptance. The single pass or two pass resue mining method should be chosen depending on the site acceptance criteria and selection criteria. The Western Metals Zinc Kapok mine site has established a set of parameters which accept the two pass resue mining method for the mining of the ore drives. The blasting results from a single pass resue method were reviewed during more recent trials in a single heading. Through a comparison of results, the parameters allowed the decision to determine the applicability of resue mining and its current form to Kapok. This paper outlines the parameters set by the Kapok mine site, reviews these in relation to the two forms of resue mining and examines the criteria which make this mining method applicable for Western Metals Zinc.

Jan 1, 2002

By Brian Stump, Chris Hayward

Blasting operations at one copper mine are studied in detail to examine the relation between blast design parameters and near-shot, in-mine, and regional seismic and acoustic observations. Five observational experiments, namely collection of blast design data, near source recordings, GPS synchronized video, near mine recordings and distant regional observations were performed during one week in August. A variety of seismic and infrasound instruments were installed near the shot, on the perimeter of the open pit mine, and at several locations up to 500 km distant. Time tagged video recordings were taken of several shots. Three shots were used in the preliminary analysis, a 350,000 lb pattern with long delays, a 60,000 lb pattern with short delays, and a 256,000 lb pattern with short delays. Maximum peak-to-peak amplitudes of the seismic signals in the mine are not a simple function of the total size of the shot, but are related to the pattern timing. Peak pressures have a less clear relation to peak pressure but match the relative amplitudes of spectra modeled from the pattern design. The predicted spectrum based upon a simple impulse model fits the observed spectrum for ground acceleration measured near the pattern and explains why in this case a pattern of 60,000 lb results in the same seismic disturbance as the 350,000 lb pattern.

Jan 1, 2002

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Simon C. Dominy, Alwyn E. Annels, Mark A. Noppé

Abstract - Mineral Resources and their subsequent conversion to Ore Reserves are of key importance to mining companies. Their reliable estimation is critical to both the confidence in a feasibility study, and also to the day-to-day operation of a mine. Together with sampling, assaying, geological and other errors introduced during interpretation and estimation, additional errors are likely to be introduced during the application of technical and economic parameters used for conversion of resources to reserves. There is thus a requirement for high-quality interpretation and estimation to be supported by high-quality data. Any company expecting to make sound investment or operational decisions must base this on both relevant and reliable information. An Ore Reserve statement generally contains a single set of grade and tonnage figures without a discussion of the potential inherent errors in these estimates. Some sensitivity studies may be run, but confidence limits are rarely quoted and, if they are, often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. Mineral Resource and Ore Reserve estimates thus carry certain errors leading to uncertainty and risk; some of these are unquantifiable for various reasons, for which the operator should be aware. This paper presents a review of the potential sources of error that might occur during a resource estimation program, which are carried through into the reserve estimate. A number of methods are discussed that allow the estimator to be more transparent about the inherent risks in his/her estimate. Emphasis is placed on data quality, and the requirement for strong quality management to be linked to continuous improvement.

Jan 1, 2002

By J. Kemeny, K. Girdner, M. A. Lowery

A strategy for proactive blast planning to improve the postblast fragmentation size has been implemented at the Phelps Dodge Morenci Mine. This strategy was developed in specific phases that include stabilization of blasting practices, systematic changes in blast design and quantification of the size distribution of blasts. Implementing this new strategy would not be possible without an accurate method for quantifying the postblast fragment size distribution. The Split image processing system is now being used to assess fragmentation size using muck pile digital imaging taken on a daily basis and an online fragmentation analysis system installed at the primary crushers. Drilling and blasting variables and fragmentation size are entered into a database, spatially evaluated in a geographic information system and subsequently utilized for mine planning purposes. Using this strategy, significant improvements have been made in postblast fragmentation and continued improvements are expected in the next several years.

Jan 1, 2002