Search Documents

"These guidelines, implemented in 2003, were recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. The guidelines are applicable to public companies and their consultants reporting diamond exploration results.“The guidelines are referenced in the Companion Policy of NI 43-101 with a statement that disclosure regarding the reporting of diamond exploration sampling results should conform to them.”Reporting GuidelinesThe following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results.In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results.Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results.The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is:Uniform within the diamond exploration industry; Consistent with reporting from other industry sectors .Comprehensive .Unambiguous .The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation.The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation)."

Jan 1, 2003

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By Roe-Hoan Yoon, lsmail Yildirim, Jinhong Zhang

Inorganic fillers and pigments such as kaolin, diatomaceous earth silica, and talc were treated with various surfactants, and the changes in their surface properties monitored. When they were treated with a cationic surfactant, they became hydrophobic and the overall surface free energies were decreased substantially. The decrease in surface free energy was mostly due to the decrease in the acid-base component (ysab) of the surface free energy, indicating that hydrophobizing an inorganic pigment entails a reduction in ysab. It was found that the surface characterization technique employed in the present work was useful for studying the effects of using various other surfactants for surface treatment.

Jan 1, 2003

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003

By Cesimiro Fabian

The crystallite size of copper electrodeposits was determined by X-Ray powder diffraction analysis using a General Area Detector Diffraction Solution (GADDS) diffractometer. Crystallite size was calculated for copper thin films which were deposited on a 316 stainless steel rotating cylinder electrode (RCE) in the presence and absence of additive ?A?. The crystallite size was calculated from a corrected full width at half maximum (FWHM) of the [110] peak profile using the Scherrer equation. The test of significant difference on crystallite size was derived using Kruskal-Wallis method. It was found that in the absence of the additive the median crystallite size was 426, which decreased to 364 in the presence of the additive. As the additive degraded, the crystallite size increased to a size similar to that observed in the absence of additive.

Jan 1, 2003

By M. Barsky, A. Govorov, E. Barsky

A study was conducted to determine the structure and lifting capacity of a two-phase stream in a vertical pipe at different distances from the point of introduction of the material into the instrument. Stream velocity was set at 2.8, 4.0, 4.8, 5.6 and 6.25 m/sec to ensure separation regimes. It was found that the llifting capacity of the two-phase stream exceeded that of pure air by a factor of three or more, and that in a turbulent regime the velocity curve displayed marked deformation, becoming more rounded and tending towards a parabola. The following formula was obtained for entrainment of a given size fraction under turbulent, laminar and transitional particle flow regimes:

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

By Lanre Oshinowo

The trend in process engineering is to design compact, more efficient processes, there is the paramount requirement to get the job done right the first time going from the drawing board to full-scale commercial operation. To accomplish this goal, there is also the need for tools beyond the traditional engineering toolkit to evaluate designs through virtual prototyping, thereby reducing the risks associated with making design decisions. One of the most important tools that has recently come to the forefront of process design and development is Computational Fluid Dynamics (CFD). CFD has been used at HATCH to address the key process parameters that drive the design of hydrometallurgical unit operations. This paper will detail the role of CFD at HATCH in achieving a superior level of confidence in the process design of autoclave circuits. Specifically, the optimum application of multiphase modeling including hydrodynamic, heat and mass transfer to hydrometallurgy operations, the impact of non-Newtonian slurry rheology on autoclave performance, and the challenges of optimizing the mixing of key reactants into slurries in autoclave reactors, is discussed.

Jan 1, 2003

By B Watson

The ConSep ACACIA Reactor is a device, which utilises a high intensity cyanidation process to achieve very high, usually near total, recovery of gold from gravity concentrates. The process utilises a fluidised bed and a chemical oxidant to enhance the gold dissolution kinetics to the point where the bulk of the dissolution occurs in a few hours. For convenience and security, most plants operate a 24-hour turn around. The product from the process is in the form of cathode gold ready for smelting by traditional means. The ConSep ACACIA Reactor performs a two-fold role. Firstly it increases gravity gold production, leading to a decreased CIP feed grade. Secondly, it removes slow leaching components from the plant leaching circuit. This two fold benefit leads to the following efficiencies: enhancement of the dissolution kinetics; enhancement of the adsorption kinetics; reduction of the gold load reporting to the carbon; a significant reduction of the ægold in circuitÆ lockup; and removal of slow leaching entities which can also result in a lowering of the required cyanide concentrations in the leaching circuit and a subsequent reduction in overall cyanide consumption. The above benefits are discussed in this paper, with a particular focus on the ConSep ACACIA ReactorÆs role in removing slow leaching components, with data generated over a 21-month period. Improvement in overall plant recovery via removal of slow leaching gold species is achieved in two ways. Firstly, some of the slow leaching entities, successfully leached under intensive cyanidation, are not always fully leached under plant conditions. This results in a lowering of the solid tailing. Secondly, the faster leaching kinetics achieved in the plant as a result of the removal of slow leaching entities results in faster and more complete adsorption of the dissolved gold onto activated carbon. This results in a lowering of the solution tailings. The construction and operation of the ConSep ACACIA Reactor is simple. Apart from the reactor body, which is a proprietary design, all components of the system are æoff the shelfÆ or specific to the siteÆs requirements. In operation of the fully automated version, a PLC controls a series of valves and pumps but except for a daily changeover process the only operating component for the bulk of the time is a relatively small solution pump. The process can be totally automated giving the security of a æhands freeÆ concentrate handling process up to the point where the product is presented as cathode gold. The ConSep ACACIA Reactor was developed by Anglogold Australia (formerly Acacia Resources) for Union ReefÆs Gold Plant and has been in production since February 1999. It has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, as of June 2003 there are eighteen full installations of the processing plant installed at mines owned and/or managed by Anglogold, Newmont, Placer Dome, Independence (formerly Lonrho), Sons of Gwalia and Harmony.

Jan 1, 2003

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By N TassT, J Cyr

At the East Sullivan site, wood wastes covering the abandoned mine tailings impoundment prevent sulfide oxidation by creating an anoxic environment. The addition of coarse ligneous wastes and their high permeability favour infiltration, resulting in a water table rise that maintains most tailings under water saturation and thus provides an additional protection against sulfide oxidation. Moreover, high infiltration allows a more rapid flushing of acid prone groundwater generated prior to the cover placement, which could cause acid mine drainage over a long period of time. Finally, the pore-waters under the cover are characterised by a strong reducing potential, high alkalinity, and near neutral pHs. These conditions favour sulfate reduction and base metal precipitation as sulfides and as carbonates. Pore-water composition monitored from 1992 to 1998 showed a significant Fe2+ decrease, following cover placement. Thereafter, the restoration strategy capitalised on the alkaline and reductive properties of the waters underlying the wood-waste cover. An original treatment of acid effluents, based on the recirculation of water discharging around the impoundment through the organic cover, was implemented. In 2002, the recirculated water from May to October had a mean pumping rate of 240 m3/h, for a total volume of 800 000 m3. Data gathered near the dispersal zone from 2000 to 2002 show that despite the recirculation of acid water (pH ÿ3), the pH decreases by only one unit from 7 to 6, during the recirculation period, ie from May to November. However, alkalinity decreases from 800 to 100 mg/L-CaCO3. Despite this decrease, the alkalinity is back up to 800 mg/L-CaCO3 the following May, thanks to sulfate reduction. From 2000 to 2002, Fe2+ concentration in the pore waters near the dispersal zone is maintained below 2 mg/L. Evolution of surface water quality suggests that the contaminated groundwater flush is completed in the north and north-west area of the impoundment; the east sector is under recovery, while the south sector remains the most problematic. A wood-waste cover, besides limiting sulfide oxidation, can fill the role of alkaline reducing barrier for the treatment of these acidogenic waters, until a balance between acidity and alkalinity in the effluent is reached.

Jan 1, 2003

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By J Krahn

In designing climate exposed soil structures such as caps and covers over mine waste it is necessary to include the wetting and drying influences of the local climate in order to accurately predict the net water, vapour and oxygen fluxes across the ground surface and through the base of the covers. The most advanced evaporative flux modelling tools currently available to practitioners have been limited to rigorous one-dimensional models (ie SoilCover) or semi-empirical two-dimensional models (ie Hydrus-2D). It is common practice to use the rigorous one-dimensional evaporative flux model results to develop a surface boundary function that can then be applied within a saturated/unsaturated two-dimensional model. However, this is not an ideal situation and results in a further approximation of the real system being modelled. This paper will highlight the use of a new modelling tool, VADOSE/W, which brings existing, rigorously formulated evaporative flux theory into the familiar setting of a two-dimensional model. The model is enhanced for simultaneous two-dimensional oxygen gas transport analysis, which has direct application in the mine waste industry. A key focus of the paper will be addressing the limitations of one-dimensional analysis for cover systems on sloping and hummocky terrain.

Jan 1, 2003