Search Documents

By J. Yvon, Inna V. Filippova

"The aim of this work is to seek the inhibitors of the meteoric and bacterial dissolution of sulphides and gangue minerals to stop the undesirable chemical reactions during conservation of the flotation wastes. The approach of passivation of surfaces by chemical treatment of the solid phase is applied for this objective.The samples taken from different depths of an old French waste dump revealed the capacity of the flotation tailings to produce acid waters (pH 1.8-2.4) and to release heavy metals. Mineralogical studies show not only the product of sulphide oxidation, i.e. sulphates, but also the complex transformations of aluminosilicates in acidic liquid phase. The detection by XRD of aluminium hydroxides (gibbsite, boehmite) allows supposing the recrystallisation phenomena during tailings conservation.Comparative tests of the passivation of the surface of sulphide minerals and waste of flotation with using of conventional reagents (CaO, NaOH, phosphates) and original reagents for this purpose (alkyl dithiocarbamates) allow to identify the optimal treatment conditions and the efficient chemicals.Leach tests were carried out in percolation columns during 68 weeks. The normalised leaching tests according to French legislation were run to confirm the selected treatment conditions. The results obtained show that a single treatment with carbamate inhibits the oxidation of the pyrite and the other sulphides, and totally prevents the formation of acid waters (the stabilised pH was 5.3-5.8). Treatment of in situ drainage water allows to obtaining a total precipitation of heavy metals: the residual concentrations of Fe, Cu and Zn are lower than 0,1 mg/l.The passivation of sulphides is the result of the formation with carbamate (studied by IR spectroscopy and XPS) of organometallic compounds, which are stable in acid medium. The presence of thiuramdisulphide (product of alkylcarbamate oxidation) at the mineral surface stabilises the mixed adsorption layer and leads to a considerable reduction in the hydratation rate of surface by avoiding the corrosion of the pyrite. No aluminium was detected in leach solution with this treatment."

Jan 1, 2003

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

By Kenneth Etschlager

The ISEE Blast Vibration and Seismograph Section provides a forum for the discussion of issues related to vibration and noise from mine, quarry and construction blasting. The section began as a Technical committee in 1995 to promote the accuracy of blasting seismographs. Currently five subcommittees exist within the section: Seismograph Standards; Seismograph Testing and Calibration; Vibration Limits, Technical; Vibration Regulations; and Program and Communications. Foremost, the Seismograph Standards section wrote the first two technical standards adopted by the ISEE. The historical accomplishments, current activities and objectives of the section are discussed.

Jan 1, 2003

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By Y. Hwang, C Kang

To understand the effect of thermal loading from HLW on the groundwater flow nearby, the coupling of TH in an equivalent porous medium is studied. Results indicate that under given conditions the alteration of groundwater flow by decay heat is localized phenomena. More comprehensive studies are underway for THM coupling. Zum Verstandnis fur die Wirkung der thermischen Belastung von HLW in der Nahe von Grundwasserstrom, ist die Verbindung von TH in den entsprechenden porigen Medium erarbeitet. Die Ergebnisse zeigen, dass unter vorgegebenen Bedingungen die Anderung von Grundwasserstrom durch Zerfallwarme lokalisiert wird. Zusatzliche umfassende Arbeiten sind fur die THM Kupplung auf dem Wege. Pour comprendre l'effet du chargement thermique de HLW sur l'écoulement d'eaux souterraines tout près, l'accouplement du TH dans un milieu poreux équivalent est étudié. Les résultats indiquent que dans des conditions données le changement d'écoulement d'eaux souterraines par la chaleur d'affaiblissement est des phénomènes localisés. Des études plus complètes sont en cours pour l'accouplement de THM.

Jan 1, 2003

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

By Riqing Ye

Laser Engineered Net-shaping (LENS TM) is an emerging manufacturing technique that ensures significant reduction of process time between initial design and final components. The fabrication of fully dense parts with appropriate properties using LENS TM process requires an in-depth understanding of the entire thermal behavior of process. In this paper, the thermal behavior during LENSTM processing of 316 stainless steel was studied both numerically and experimentally. Temperature distribution and gradient in the fabricated 316 stainless steel part were obtained by Finite Element Method (FEM) simulation. The numerical results are in good agreement with the experimental observations. The numerical method may be used to optirnize process parameters and predict the thermal response of LENSTM fabricated components. Key words: Laser Engineered Net-shaping, Thermal Behavior, Finite Element Analysis

Jan 1, 2003

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By Adam Feiler, John Ralston

Optical reflectometry was used to study the attachment and subsequent detachment of silica particles (diameter 25 nm) from the surface of titanium dioxide wafers under well-defined hydro- dynamic conditions. Atomic force microscopy was used to measure the interaction between silica spheres (diameter 7 pm) and titanium dioxide wafers under the same solution conditions. In addition to repulsive electrical double layer forces, adsorbed polyphosphates provide a short-ranged steric layer that reduces the lateral interaction between the surfaces. The use of these two complementary techniques has given valuable insight into the process responsible for fine particle detachment and has particular application to surface cleaning.

Jan 1, 2003

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By Se-Won Chang

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese nodules on the Campbell Drift, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. During the research voyage SAA3 by R/V Tangaroa (TAN 9909) in July-August 1999, seafloor sampling and camera towing were conducted along the two transects across the known flow path of the Deep Western Boundary Current (DWBC) perpendicular to the lowermost margin of the Campbell Plateau and Bollons Seamount. The four major nodule facies, SHH (slope hydrogenetic nodules with high density), AHH (abyssal hydrogenetic nodules with high density), ADH (abyssal diagenetic nodules with high density), and ADL (abyssal diagenetic nodules with low density) were identified. Two additional minor nodule facies, SIB (slope irregular nodules with ice-rafted boulders) and SHB (slope hydrogenetic nodules with boulders and crust), of localized distributions are also identified.

Jan 1, 2003

By K Matsui, T Sasaoka, S Kubota, Y Yosh

A large amount of wastes from the preparation plant is produced. The properties of these wastes vary depending on the mineralogical contents of the mother rock in which the coal is embedded. The waste quality depends on the method of mining and cleaning. The waste mainly consists of clays, quartz, carbonaceous materials, mica, pyrites and so on. About 55 per cent of coal-ash is now utilised and the remains are disposed of at the disposal sites, however, the life of the disposal site is limited. Moreover, it is difficult to find new disposal sites. Therefore, it is requested that the percentage of the utilisation of the coal-ash be increased in every field in Japan. So, it is very much available if the injection material for natural/artificial openings can be applied on the cement that is added to flyash. Among the man-made pozzolans, a flyash is probably the most successful component used in grout injection. When flyash is added to Portland cement concrete, the same kinds of oxides as those of the cement are being added. As an injection component, flyash acts, in part, as a fine aggregate and, in part, as a binding component. However, there is not a substantial alteration of the properties of the original component. From these points of view, in order to clarify to what degree the flyash content affects the properties of the injected grout mixture; different combinations of flyash, Portland cement and water were considered by means of several experiments.

Jan 1, 2003

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003

By Andrei Kolesnikov

"The results of CFD modelling of complex heat transfer and fluid flow in DC electric arc furnace are presented. The model includes energy and momentum conservation equations for gas phase (freeboard), liquid phase (molten bath) and solid phase (walls and graphite electrode). Simulation revealed the temperature distribution in all elements of the furnace. The influence of the arc and melt resistance on the temperature distribution is discussed.Computational Fluid Dynamics (CFD) becomes a powerful tool for better understanding of the heta and mass transfer processes in industrial equipment. In current work commercial CFD software STAR-CD was used to analyse complex heat transfer in DC EAF, including forced and natural convection, conduction and radiation. The finite volume solver using body-fitted grid was used. The grids are non-staggered hexahedral grids and all variables are evaluated at cell centers. Steady-state calculations were performed with PISO algorithm. For the convective terms in equations the hybrid differencing scheme was used. An upwind differencing scheme was used for other terms. Conjugative heat transfer was taken into account in heat transfer calculations on gas-liquid and gas-solid interfaces. Radiation from the arc and inner surfaces of the furnace was calculated by a “discrete beam” approach. Source term in energy conservation equation was used to represent heat release in the zone occupied by the DC electric arc. The volume of this zone was calculated from semi-empirical equations. The Joule heat and heat due to chemical reaction in the melt were calculated through the source term expression in the energy balance equations for the slag and metal in the molten bath. The gas acceleration in the electric arc zone and stirring of the slag due to gas bubbles motion were accounted for by momentum source terms in the momentum conservation equations.All simulations were carried out using axisymmetric two-dimensional grid. The grid resolution was 20 cm per cell in most part of the furnace, except the arc region, where resolution was 5 mm per cell."

Jan 1, 2003

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors&apos; records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By J. E. Gebhardt, D. King

Field-testing of a new on-stream X-ray fluorescence analyzer was conducted in a copper concentrator. The evaluation of copper tailings and concentrate streams indicated a statistically acceptable correlation with laboratory chemical analyses. The new equipment employs a “components off-the-shelf” approach to minimize capital cost and maintenance issues and to utilize the latest advancements in X-ray fluorescence detector technology and computer capability. A general description of the system is provided, and performance of the analyzer measuring copper (Cu), iron (Fe), and molybdenum (Mo) is presented.

Jan 1, 2003

By R. Chiarizia

Third phase formation, i.e., the splitting of the organic phase in two layers, is a common feature observed, under conditions of high loading, for many solvent extraction systems of both analytical and industrial interest. Although this phenomenon has been investigated in a large number of works, a structural and physico-chemical description is still lacking. In this work, small-angle neutron scattering (SANS) data for the tri-n-butylphosphate (TBP)-n-octane,Th(NO3)4-HNO3 solvent extraction system have been interpreted using the Baxter model for hard-spheres with surface adhesion. The increase in scattering intensity in the low Q range, observed when increasing amounts of HNO3 and/or Th(NO3)4 are introduced into the organic phase, has been interpreted as arising from interactions between small reverse micelles containing three TBP molecules plus solutes in their polar core. This intermicellar attraction, under appropriate conditions, leads to third phase formation.

Jan 1, 2003

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003