Search Documents

By J D. Bryant

The Ernest Henry Copper-Gold mine, the third largest copper deposit in Australia, is located 35 km NE of Cloncurry in the Mt Isa-Cloncurry mineral district of NW Queensland. Ernest Henry Mining Pty Ltd (EHM), a wholly owned subsidiary of Xstrata Copper Australia, operates the mine. Approximately 10.2 Mt of ore grading 1.12 per cent Cu and 0.56 g/t Au were processed during the 2001 - 2002 financial year. The Ernest Henry plant produces copper-gold concentrate, which is trucked to Mt Isa for smelting. The Ernest Henry deposit is a member of the diverse Fe-oxide-(Cu-Au) class of deposits. The orebody is hosted within a sequence of moderately SSE-dipping, intensely altered Paleoproterozoic intermediate metavolcanic and metasedimentary rocks. Copper (chalcopyrite)-gold mineralisation occurs mainly within the magnetite-biotite-calcite ¦ pyrite matrix of a 250 m + 300 m pipe-like breccia body. The breccia pipe comprises two anastomosing lenses separated by a lower grade, clast-supported breccia zone. Several anastomosing brittle faults affect the macro-geometry of the orebody. Copper grade is proportional to the degree of matrix support in the breccia. The July 2002 Ore Reserve was 88.7 Mt @ 1.0 per cent Cu and 0.5 g/t Au. Resource estimation at Ernest Henry is based on a large database of predominantly diamond drill hole information. Drill spacing is typically 50 m + 50 m. Ordinary kriging is used to estimate Cu, Au, SG and IST (oxidation indicator) into model parent cells of dimension 20 m E + 20 m N + 16 m RL. The block model is comprised of five geological-geochemical domains represented by 3D wireframe surfaces. Zonal control, where samples and blocks are assigned the same domain number, is used to control grade estimation. The geometry of the domains defines hard grade boundaries across strike and soft boundaries along strike A Deep Drilling Project was initiated in August 2002 with the initial aim of testing the down-plunge extension of the orebody to a vertical depth of over 1 km. The encouraging intersections to date have resulted in a significant increase in the mineÆs open pit Mineral Resource together with the identification of an underground Mineral Resource. Added benefits of the project included an expanded and updated geological legend and an improved understanding of the host geological sequence.

Jan 1, 2003

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003

Quantitative probabilistic ecological risk assessment has been used to evaluate the likely effect on fish diversity and abundance of filtered and bioavailable metals in streamwater affected by acid drainage from the abandoned and remediated Rum Jungle U/Cu mine in the Northern Territory of Australia. The water quality was determined using monitoring data from a gauging station on the East Branch of the Finniss River, downstream of the mine site, and modelled assuming a number of potential water quality management options. The management options ranged from no action, through some flushing options to full catch and treatment of contaminated seepage from the waste rock heaps. The computer code AQUARISK was used to undertake the analyses. Critical criteria for contaminant water concentrations at the site, derived from probability density functions of available fish ecotoxicology data, were found to closely approximate the regulatory trigger values for the contaminants of concern. Modelled predictions of reduced diversity and abundance were also in good agreement with in situ biodiversity measures. Based on a reasonable target of 67 per cent species tolerance for this heavy impacted site, it was found that none of the low cost options for wastewater management was acceptable. Combinations of two of the options approached acceptability. Both of the catch and treat options exceeded the arbitrary acceptability target well. This implied that the more expensive option of liming to pH 10 might be unnecessary at this site. Thus, the use of ecological risk assessment modelling has proven useful in undertaking cost-benefit analyses for this site. The approach provides a management decision-making tool that can be economically used to link expensive on-site environmental engineering options with site-specific ecological goals rather than the previous nebulous aims of æreduced contaminant loadÆ or æimproved biodiversityÆ that often resulted in excessive expenditure without achieving successful environmental benefit.

Jan 1, 2003

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

Environmental and public concerns and the banned use of cyanide for the recovery of gold in some parts of the world have heightened the search for an alternative lixiviant to cyanide. Thiosulfate appears to be the most promising alternative to cyanide due to thiosulfate being non-toxic, relatively cheap compared to cyanide and generally gold recoveries are similar to those of cyanide. The most widely researched thiosulfate process is one where copper ions and ammonia are added to the solution. This paper reviews the leaching of gold in thiosulfate solutions and the contributions of the research at Monash University to the understanding of the gold oxidation reaction in thiosulfate solutions, the solution chemistry when copper ions, ammonia and oxygen are present, the influence of the changing solution chemistry on the gold leach kinetics, and the application of thiosulfate in the leaching of gold from ores. It is clearly shown that the gold oxidation rate is hindered in thiosulfate solutions. In the presence of copper ions the gold oxidation rate though is significantly enhanced and thus is why copper(II) is more effective than other oxidants in the thiosulfate leach system. The copper-ammonia-thiosulfate leach solution chemistry is shown to be very complex, especially in the presence of oxygen as the rate of thiosulfate oxidation increases and the majority of the copper ions are not maintained in the copper(II) oxidation state. The thiosulfate oxidation rate must also be maintained low as an intermediate thiosulfate oxidation product hinders gold leaching. In optimising the recovery of gold from ores with copper-ammonia-thiosulfate leach solutions it is important to evaluate and minimise any negative effect an ore may have on the leach solution chemistry and hence gold leaching.

Jan 1, 2003

By Chris J. Martin, Nichola A. McKay

"In mid-2001, North American Palladium commissioned a new 15,000 tonnes per day milling and flotation circuit at their Lac des Iles Mine (LDI), one of only two primary platinum group element (PGE) producers in North America. The mill treats an ore containing 2.3 g/t PGE producing a concentrate assaying 300 g/t PGE, at a recovery of roughly 75%.Top-size control crushing is conducted ahead of semi-autogenous milling. A portion of the SABC circuit feed is crushed to –25mm to increase mill throughput. Product from the SABC circuit is fed to flotation. Flotation consists of roughing and scavenging, with the rougher and scavenger concentrates each being reground using vertimills. Cleaner flotation uses two stages of cleaning using mechanical cells, and a third stage using flotation columns, the column tails being scavenged using a bank of mechanical cells. Rougher concentrate by-passes the first cleaner circuit. Reagents added include amyl xanthate collector, dithiophosphate promoter, MIBC frother and a carboxy methyl cellulose-based gangue depressant.SGS Lakefield Research, together with staff at LDI initiated a structured plant optimisation program comprising on-site testing, bench-scale flotation and mineralogical analysis using QemSCAN. The objectives of the mineralogical studies were 1) to identify feed PGM, their size distribution and mineral associations, 2) establish relationships between the PGM mineralogy and PGM floatability, and 3) characterize the culprit silicate minerals diluting the final concentrate.PGM flotation response at Lac des Iles is clearly bi-modal in nature, with about 60% of the PGM floating quickly, to a high value rougher concentrate. The mineralogical work was able to explain the causes of the bi-modal PGM floatability, which in turn created new opportunities for the metallurgists to optimise the circuit."

Jan 1, 2003

By S Strohmayr, R Harvey, A See

Ernest Henry Mining Pty Ltd started production in August 1997. The Ernest Henry orebody consists of two distinct parts, a complex supergene ore zone overlying a primary ore zone. The economic copper minerals in the supergene ore were chalcocite, bornite, secondary chalcopyrite and native copper while the primary zone has only chalcopyrite. The variability of the supergene zone made concentrator operation difficult and predicting metallurgical performance using mineralogy essential to establish the capabilities of the concentrator. A paper presented at the 1998 Mine to Mill Conference entitled Mineralogy Controlling Metallurgy at Ernest Henry Mining (Barnes, Strohmayr, Brindley and Munro, 1998) presented the testwork and initial plant surveys that showed that the mineralogy of the ore controls the metallurgy of the concentrator. This paper presents the data obtained from the subsequent years of operation treating both the supergene and primary ore types. A review of the actual supergene mineral distribution in feed and subsequent recoveries compared to those predicted as part of the flowsheet design is also presented.

Jan 1, 2003

By S. Kelebek, A. Khan, J. Caceres, D. Beckett

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance (Figure 1). The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents (Figure 2)."

Jan 1, 2003

By Gunnar Nord

Shifting ground conditions when tunnelling often call for different methods of attacking the tunnel face. In order to overcome problems with local unstable soft ground in a hard rock tunnelling project the Boodex method offers a cost effective alternative. Boodex and variants of it is a combination of two well-known techniques, drilling with Boomer rig using Odex gear. It will give a steel lined hole ready for grouting and the steel pipe has a load bearing capacity that means that a spiling effect is achieved. In this paper the method and some applications will be described with possibilities and limitations.

Jan 1, 2003

By D. Whittles, S. Kingman, K. Jackson, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

The minerals industry contributes to the economic growth, prosperity and quality of life of nations, particularly in areas where there might be limited opportunities for employment in other sectors. However, notwithstanding their economic importance, the minerals extraction and processing industries are considered to have significant impacts on the surrounding environment. In recent years many mines have implemented modern monitoring technology and modelling of the monitored environmental parameters to provide scientifically proven indicators about the state of the environment. The flexibility required by the minerals industry to respond dynamically to a changing natural, social and economic environment has become a major consideration. Whilst the notion of continuous improvement is embodied within most environmental management systems, what is now required is a structured audit trail which tracks the flow of resources through the production process to the ultimate environmental impact associated with their consumption, transformation and disposal. Imperial College is coordinating an EC funded project, which is developing a methodology to minimise the ?full life-cycle? impact of metalliferous mining projects, adopting an integrated approach to production and process design, and the costs involved. In order to develop a life cycle assessment (LCA) system that will incorporate different types of data related to the minerals extraction operations, a data inventory was designed and coded in an object-relational database model. The calculation procedures accounting for the input/output balance of the alternative scenarios for mining production, processing, waste disposal, monitoring, and their financial implications are being programmed into a software system. This paper presents the rational and innovative aspects of this work. The methodology developed for the life cycle database is illustrated for the mining production and gaseous emissions components of the system.

Jan 1, 2003

Marble has been recognized as a valuable natural resource ever since ancient times. Due to its peculiar aesthetic and technical characteristics as well as the lithotype uniqueness, it has widely been appreciated over the past centuries. In present times its production and demand are enjoying an increasing trend, with comparatively high market prices. All this considered, marble can be included among these natural resources whose exploitation provided, and still provides, an important contribution to the growth of the economic system. Nevertheless, there is at least one more important reason that makes marble a valued resource. For ages, marble represented one of the most important raw materials for sculpture sand architectural masterpieces, which constitute part of the cultural heritage of mankind. With this in mind, the value of marble is strictly related to its extraordinary capability to preserve cultural heritage and therefore to convey civilization from past to future generations. In other words, the role of marble should be recognized as being of the utmost importance in order to attain an overall objective of ?cultural sustainability?, that is, the assurance of the inter-generational flow of the cultural heritage capital. To achieve this sustainability goal, the priorities should be to protect and preserve the world?s artistic and architectural historical heritage, which require restoration works. In this field, a very il task is entrusted to the extractive industry: this industry, in cooperation with historians, art experts and public authorities, is in charge of detecting and supplying historical stones for restoration purposes, taking into consideration that, in order to restore a monument in a correct way, the same lithotypes the monument was made from are needed. These marbles are often no longer in production, so that it becomes necessary to find the location of the original quarries, as only there is it possible to extract even the small quantities of stones that are needed. In this case, the stone, located in its geological context, could have such valued characteristics as to be considered an important public asset and consequently a resource to be preserved and protected even beyond the market conditions. This important task should be carried out by the public administration through a targeted intervention of territorial planning and monitoring, which could include the support for the specific extractive activity.

Jan 1, 2003

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By V. N. Kazakidis

With increased levels of automation, capitalization, and empowerment of citizens, the traditional axis of labour versus capital or national government versus capital, upon which the allocation of benefits from a mining project was traditionally based, has shifted primarily to a capital versus community axis. In light of this paradigm shift, it is critical for the sustainability of mining that economic indicators be considered at the pre-feasibility, feasibility, and permitting stages of a project. Such indicators should emphasize the ?ripple effect? of the economic impact of a capital-intensive mining investment on a region due to outsourcing, as well as the diversified spin-off opportunities and the technological advances that can be exploited by local communities.

Jan 1, 2003

By L. H. Michaud

"Albian Sands Energy (ASE), an oil sands surface mining and extraction operation, is currently undergoing start-up and is scheduled to ramp-up to full production by mid-2003. Startup includes the selection and implementation of over 75 IT systems or computer applications which include: engineering applications; systems required to control mining activities, maintenance, the processing plant and utilities; and also systems required to run the company, such as human resources, finances and inventory/ warehousing.This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in ASE’s approach to identifying system requirements is the development of a business activity model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been led by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that do not meet the company’s expectations. To ensure a more positive outcome, ASE believes that it is imperative that the company’s technical and business people be closely involved in the selection process.Integration of the IT systems is also key, including linking all applications through a data warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company"

Jan 1, 2003

By Ramon V. V de Araújo, Roberto B. E Trindade, Pablo R. Fica-Piras

"Lead has been reported to affect blood vessels and kidneys. It also produces adverse effects in the mental and physical development of children and nervous system of adults. It is also considered as a possible cause of cancer. Because of all these threats to the human life, the reduction of its environmental occurrence, by means of recycling, is an important additional advantage to the usual ones derived of the procedures of the secondary metallurgy: lead can be recycled several times maintaining its characteristics equivalent to the primary one.Furthermore, this way of producing the metal avoids the environmental impacts of primary lead melting. Also, as an additional advantage, it triggers the metallurgical process with a raw material in what we observe higher lead content than in the natural ores. Some of the potential sources for these purposes are: ashes, slags, electrode residues, anodic muds, spent electrolytes, solid and liquid wastes, industrial or automotive catalysts, worn-out or obsolete equipment components and/or final consumption products.About 40% of world’s lead production comes from automotive batteries, mainly composed of four parts: plastic box, electrolyte (diluted sulphuric acid), contacts and connectors of Pd-Sb and plates (PbSO4, PbO2 and PbO). The plates represent 75% of the total mass. Metallic parts can be melted at moderate temperatures and then refined. The remaining fraction, constituted by the non-metallic portions, can be recovered by hydro and electro-metallurgical routes. These routes are preferred instead of pyrometallurgical ones due to the ultimate emissions of lead particulates and sulphur dioxide.The principal constituent of the residual paste of batteries is the lead sulphate. In this process, the paste is treated in two stages: in the first, lixiviating with Na2CO3 (desulphurization of the paste), obtaining PbCO3 and Na2SO4; in the second, the lead carbonate is lixiviated with HNO3, producing Pb(NO3)2, soluble, that can be converted to metallic lead by electrolysis. The reaction of PbSO4 with Na2CO3 in aqueous solutions is fast: the global rate is limited by the diffusion of the carbonate ions inside the reaction medium."

Jan 1, 2003

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003