Search Documents

By F. F. Peng, Y. Xia

In modeling of hindered-settling bed separators, the published separation mechanisms are based on differences of particle density and size distributions, without the details of complexity of particles-liquid interactions. A fluid dynamic model for the separator is developed using Euler-Lagrange approach of Computational Fluid Dynamics (CFD). Fluid motion is obtained from solving the movement of liquid governing equations. The damping effect on flow pat-terns caused by the movement of particles resulted in liquid-particle coupling is included in the model. Effects of particle size, and particle density compositions, feed rate, feed water flow rate, upward fluidizing water flow rate, etc., are simulated in the 2-D separation model. Flow pattern effects on the separation of fine particles in the separators with center downward-flow and side cross-flow feed systems are investigated.

Jan 1, 2004

By K L. Brown

In the Waiotapu geothermal area only Champagne Pool, 109 ng/L, and Waiotapu Geyser, 7.6 ng/L, have dissolved Au concentrations greater than 5 ng/L and most springs have concentrations less than 2 ng/L. When Au concentration data are combined with other physico-chemical data from each spring including; pH, reduced sulphur concentration and temperature, the degree of Au saturation can be calculated. All samples sites except Champagne Pool, Waiotapu Geyser and the Artists Palette are under-saturated with respect to Au(s) by 1 to 3 orders of magnitude. This indicates that adsorption or co-precipitation or both are important processes depositing Au beneath hot springs. Deposition of Au by adsorption or co-precipitation beneath hot springs implies that dissolved Au may not have to reach saturation concentrations for ore to deposit. This interpretation is supported by the presence of substantial Au as sub-microscopic components within sulphide minerals in ore deposits and indicates depositional efficiency beyond that possible through precipitation of Au(s).

Jan 1, 2004

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in1994 initiated a dynamic shift in the ownership, management and development of the country?s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress?s Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since then there have been important changes affecting the rules of mineral development. These are: ?A drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully ?The globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists and ?The introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its regulations, the much publicised Broad-Based Socio-Economic Empowerment Charter, its associated Scorecard, and the Draft Royalty Bill.

Jan 1, 2004

The paper deals with the importance of design and of codes of practice in ensuring safe working conditions in mines. The design principles involved in the design process are dealt with, and the importance of a logical design process is emphasized. The links between the requirements for developing a code of practice, embodied in the existing guidelines for the preparation of such a code, and the design principles and process are considered in some detail. Finally, suggestions are included, which may provide improvements to the code and hence, ultimately, lead to further improvement in safe working conditions.

Jan 1, 2004

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004

By Francis R. McAllister

SYSTEM ENGINEERING Years ago, while attending Harvard's Advanced Management Program, Professor Robert Hayes introduced our class to the, then not-so-familiar, concept of systems engineering. First assignment-dinner at The Benihana of Tokyo Restaurant! Delighted, but a bit mystified with the assignment; we had dinner at Benihana. Back in class, Professor Hayes inquired about the assignment and persuaded us; that Rocky Aoki's business formula for Benihana was not necessarily Japanese cuisine, but rather the systematic way in which he moves more people-if you will, processes more people through his restaurants than his competition, by systematically linking all restaurant functions. For instance, the bar is a holding area in which patrons ideally wait no more, or no less, than 20 minutes. When seated, your table, which accommodates eight, is filled with eight even if you are a party of two. The Japanese chef is also the entertainment, and when, at the end, he cleans the grill, you are being subtly prompted that dinner is over. The bill accompanies ice cream, systematically delivered shortly thereafter. You are expected to pay promptly and depart, as there are eight more, mostly unacquainted, people who have waited 20 minutes in the bar, and who are assembled ready to be seated at your table. For me-this was electrifying. I understood the concept, concluded it was very powerful and felt prepared to conquer whatever, by means of its application. That was years ago and I can safely say I have yet to fully realize on the euphoria of that moment. Why? Well, I simply conclude: • The concept of systems engineering is simple and not revolutionary, but The application of systems engineering is far from simple and is revolutionary.

Jan 1, 2004

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004

By S. Afshar, C. Allaire

Several studied have recently shown that the use of non-wetting additives is not always a sufficient solution to improve the corrosion resistance of refractories against molten aluminum. Once in contact with liquid aluminum, the coarse aluminosilicate aggregates, which do not benefit from the protective effect of non-wetting additives in the matrix, may be corroded. In some cases, the corrosion of aggregates, especially those containing a significant amount of free silica and/or alkalis, promotes corrosion in the surrounding matrix. The present work explores the possibility to protect the poor corrosion resistant aggregates via a lining procedure. A slip casting method, using either alumina or celsian-like composition based slurries, has been applied for lining of a series of aggregates. The results from this study show that such linings may prevent efficiently the corrosion of aluminosilicate aggregates. This work also analyzes the effects of firing temperature and lining quality on the corrosion behavior of aggregates

Jan 1, 2004

By J. R. Mattern

The engineering geology of the Rio Tinto Borax Boron Mine creates challenges in providing practical slope design recommendations to mine planning engineers. Low strength sedimentary units interbedded with very low strength lakebed clays surround the orebody. Faulting has offset and juxtaposed these units into variably adverse orientations, while groundwater is compartmentalized both vertically and horizontally within fault blocks. A collective program of geologic data collection, geomechanical strength testing, geologic modeling, slope depressurization, confirmation of underground stope locations, and documentation of slope behavior provides vital information for design investigations and sensitivities. Analysis results lead to risk assessments and operational procedures that add value to the business by optimizing slope configurations and minimizing risk.

Jan 1, 2004

North American Coal is a subsidiary of NACCO Industries. Originally founded as Cleveland and Western Coal in 1913, North American Coal took its present name in1925. Today, North American Coal is one of the 10largest coal producers in America, mining about 32Mt/a (35 million stpy). The company mines primarily lignite for electric utilities. Its current operations are in North Dakota, Texas, Louisiana, and Mississippi. In addition, North American Coal’s Florida operation provides dragline mining services for quarries that produce more than 18Mt/a (20 million stpy) of limerock. With more than 1.8 Gt (2 billion st)of bituminous and lignite coal re-serves in the United States, North American Coal constantly seeks new technologies to keep its operations modern, productive and cost competitive.

Jan 1, 2004

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

German manufacturer DBT signed a contract to supply a sixth automated-plow long-wall system to Shenyang Coal in Liaoning province in northeastern China. This most recent order occurred just weeks after DBT signed a contract to deliver a fifth automated-plow longwall system to Datong Coal in Shanxi province. The plow will go into service at Shenyang Coal’s Hongyang Mine. Mining conditions at the mine, coupled with DBT’s advanced automated-plow technology, means that the system has the potential to become one of the world’s most productive thin-seam longwalls.

Jan 1, 2004

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By D R. van der Meulen, P Ande, D J. Lunt

Pressure hydrometallurgy is becoming an increasingly common unit operation in the treatment of gold and base metal ores and concentrates. The design of an adequate and appropriate pilot-scale testwork program is, therefore, essential in order to minimise the risks associated with developing a project in which autoclaves form a key part of the operation. This paper identifies the approaches that have been taken in the piloting of oxidative and pressure acid leach operations. Particular emphasis is placed on the determination of scale-up ratios between the pilot and commercial plants and the pilot-plant run durations. The issues, both metallurgical and project-specific, that can impact these key parameters are reviewed.

Jan 1, 2004

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By Winfried Rosenstock

AEBT has been available for a couple of years and is successfully applied in Australia. Up to now it was mainly used in coal surface mining at the Australian East- Coast. Presently, the proved results reach ~ 50 % reduction of Drilling & Blasting costs and a productivity increase of between 10 and 20 %. In 2003 it was for the first time used in surface metal-mining. The mine features for the time being an extremely difficult geological environment and had above to be carried out in the transition level waste/ore. Reductions of wall control, powder factor and vibrations were the main target.

Jan 1, 2004

By Alan Campoli

Approximately 100 million fully grouted rebar roof bolts are installed each year in the United States, 80% are B-Series (5/8 inch fully grouted rebar in a one-inch borehole). The lesser used more expensive A-Series (3/4-inch fully grouted rebar in a one-inch borehole) maximizes resin performance. Standard B-Series provides only 60% of the pull out resistance of A-Series. The Eclipse System was developed by Minova USA Inc. and marketed with Excel Mining Systems to improve the performance of B-Series. A 1/8-inch offset bolt head combined with a specially formulated Eclipse Lokset resin cartridge results in increased mixing efficiency and more uniform resin anchorage. Over two million units have been sold to date; the majority of these Eclipse bolts have been sold to coal mines in the Illinois Basin. Pull testing has demonstrated that a Grade 60 Eclipse bolt provides equal or superior pullout resistance as compared to a Grade 40 No. 6 rebar. Short encapsulation pull tests have yet to consistently demonstrate the superior pullout strength of Eclipse to standard B-Series, however 12 inch Eclipse grouted columns have successfully held in excess of the bolt yield load. The successful substitution of Eclipse bolts for A-Series has significantly reduced the primary roof support costs by approximately $0.18 per foot of bolt. Recent over coring analysis of various anti-gloving methodologies performed in New Zealand has confirmed the superior mixing of the Eclipse system (5).

Jan 1, 2004

By Ronald D. Mariani, Gregory E. Mahoski

BACKGROUND The steel and iron ore industry has had a long history of an adversarial relationship with its union and workforce. The Empire Mine during its first 40 years of existence was no exception. The "we-they" mentality went hand-in-hand with the normal by-product of an adversarial relationship, grievances and arbitration. This relationship was considered the norm and it was not until the late 1970s that consideration was given to changing this relationship. At this time the industry was involved in a fight for existence and the economic pressure demanded increasing productivity to lower cost. The challenge to survive highlighted the fact that an adversarial relationship was not conducive to attaining the needed gains in productivity. The first formal attempt to change the way we worked came in the 1980 Labor Agreement which provided for the opportunity to utilize Labor Management Participation Teams (LMPTs). LMPTs were established at the Empire Mine and they functioned for a couple of years. The teams spent most of their time working on creature-comfort issues and steered clear of dealing with productivity issues. Mine shutdowns had occurred in Michigan resulting in large layoffs, and the union was trying to add jobs and was not supporting teams that could increase productivity and eliminate jobs. When the 1986 labor negotiations began, the local union pulled their support of the LMPT process. Other initiatives were negotiated over the years to foster a change in the culture but, as with the LMPT program, they did not produce the desired culture change. It became abundantly clear: you cannot negotiate a culture change.

Jan 1, 2004

By Emmanuel N. Zevgolis

After the Krupp-Renn process was shown to be unsuitable for treatment of the Greek nickeliferous laterites, the LM process was developed. It involved roasting reduction up to metallic iron in a Rotary Kiln (R/K) and smelting in an Electric Furnace (E/F). Ferronickel (with 15% Ni) produced in the E/F, was upgraded to 90-95% Ni in an 02 converter. Raw Ni was then electrolyzed to pure Ni. The LM process was not applied for very long however, due to various problems. So, the Larco process was developed, i.e., pre-reduction in R/Ks, smelting of the calcine in E/Fs for ferronickel production (15% Ni) and enrichment to 20% Ni, in an O2 converter. Until now, many technological improvements have been invented and applied or adjusted to the process, which have made it a fully reliable and competitive one. sohe of the improvements were the invention and application of a new granulation process for liquid ferronickel, the modification of the existing R/Ks, E/Fs and converters and the design of new ones, and others that are described in the paper. Keywords: Ferronickel, metallurgy, laterites, LM process, Larco process

Jan 1, 2004