Search Documents

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By Adrian J. Moore, Alan B. Richards

Airblast overpressure levels can commonly be increased by up to 20 decibels (dBL) by the effects of meteorology, due to inversions and wind shear. Existing atmospheric refraction models can provide a good evaluation of the effects of meteorology, but have been limited in the accuracy of their outputs by the accuracy of the meteorological data that is available for input. This paper uses case histories from open-pit coal mine blasting in the Hunter Valley area of Australia to provide examples of increases in airblast due to inversions, wind shear, and a combination of both. It gives details of our experience of the accuracy with which predictions and assessments can be made using meteorological data of various levels of accuracy, and on the design buffer that is required to prevent the exceedence of airblast limits. The accuracy of meteorological prediction and assessment will shortly be improved by the use of sounding equipment that gives continuous measurements of temperature and wind velocity at significant levels above the ground. The paper also gives details of an industry funded research project that aims to permit the effective use of this data at distances many kilometres (km) (miles) from the location of the sounding equipment, and to develop a short term predictive model that will permit the amount of meteorological reinforcement that will occur at firing time to be determined before a decision is made to tie up a shot.

Jan 1, 2005

By J R. Hernandez-Aguilar, C O. Go, C Acuna

The gas dispersion properties that are the subjects of this communication include three measured parameters, gas superficial velocity (gas rate), gas holdup and bubble size, plus derived parameter, bubble surface area flux. Over the past ten years sensors to measure these parameters have been introduced and those originating from McGill University are briefly described. The sensors have seen extensive use in plant campaigns and experiences on four cell types at three sites are discussed. The impact of frother in controlling bubble size by retarding coalescence is illustrated, introducing the need to understand chemistry/machine interactions in interpreting gas dispersion results. An increase in Sauter mean bubble size (D32) with superficial gas velocity (gas rate, Jg) was found, which followed the empirical relationship where Do ~ 0.5 - 0.6 mm and C and n are fitted parameters dependent on the system (machine and chemistry). Following this trend in Db - Jg, consistent bubble surface area flux (Sb) - Jg trends are also observed. The trend in Sauter mean versus number mean (D10) is used to help interpret the nature of the distribution; as the means approach numerically, the distribution is narrowing. Analysing gas holdup versus gas rate shows both a dependence on location in the cell as well as cell position in a bank, factors which must be accounted for when comparing data from different plants and circuits. The instrumentation and methodologies being developed are presenting new opportunities for incorporating cell hydrodynamics into metallurgical diagnostics. A case study at one plant serves as illustration.

Jan 1, 2005

By C J. Larder, S E. Turner

The concept of underground grinding is not new, but to a metallurgist and a mining engineer this could be considered unconventional. The idea of pumping a ground slurry several hundred metres from underground in a single lift could also be considered to present a daunting engineering challenge. Using a practical example of a mine in Australia where the owners have requested not to be identified, this paper challenges the conventional thoughts on these concepts and shows that with basic sound engineering practices the production of a ground slurry from underground could potentially provide significant operating cost savings. The supply of ore from the underground mine is currently drawn from depths approaching 800 m below the surface. The cost of hauling the ore to the existing underground crushing station located 500 m below surface has been steadily increasing. A number of alternatives to reduce the mining and processing unit operating costs were examined by Sinclair Knight Merz (SKM) and the mining company. The most radical of these is the use of hydraulic hoisting of ore at an increased production rate. Numerous questions were asked, such as: How does one get a SAG mill or an HPGR crusher underground? Where does one locate a grinding mill underground? Does the technology exist to pump the slurry to surface in a single lift? What will be the cost benefits? What are the risks involved? The study covered the two main technical issues underlying the potential benefits. Firstly, technical evaluations were undertaken on the pumping technology currently available for single and multiple lifts to surface. Secondly, the issues relating to the feasibility of delivering and locating a SAG mill underground were reviewed. Although the capital costs for this project are significant, the operating cost savings showed a potential payback period of less than two years, and furthermore provide the basis for an increased mine life, especially at lower metal prices.

Jan 1, 2005

By R Verreet

In April 2000 Mount Isa Mines installed hoist ropes of a new design on the double-drum winder at their P49 shaft. The ropes, CASAR Duroplast, were about three times as expensive as the previously used triangular strand ropes. The P49 shaft is situated at Mount Isa MinesÆ George Fisher Mine, located some 30 km north of Mt Isa. This shaft used the tried and proven 6 x 33 triangular strand style ropes. The rope life attained by these ropes at the time was acceptable due to many years of satisfactory performance. The following study indicates the improvement of service life using CASAR Duroplast rope in P 49 shaft, which depends on shaft and winder parameters of that particular shaft and cannot necessarily be generalised to other shafts.

Jan 1, 2005

By J L. Mauk

 Broken Hills is an adularia-sericite epithermal Au-Ag deposit, hosted in flow-banded rhyolites and overlying rhyolitic pyroclastic rocks in the eastern Hauraki Goldfield. The 7.1 Ma deposit was the largest producer of gold in the eastern Hauraki Goldfield, and was one of very few economic deposits hosted in Pliocene rhyolites. This paper presents the results of a recent study in the upper levels of the deposit. Maps and cross-sections constrain structural and lithological relationships, and the lateral and vertical extent of a breccia pipe û the major feature of the upper levels.   Previous studies in the upper levels of Broken Hills have shown that gold and silver values are concentrated around and within a large breccia pipe, mined by a series of æcaveÆ stopes and in veins. Contour diagrams of Au-Ag data from channel samples indicate that the breccia pipe was a major fluid channel-way for mineralising solutions.   The breccia pipe deposits are part of the dynamic geothermal system that formed the Broken Hills ore bodies; they developed as a result of hydrothermal brecciation in areas of structural weakness within a rhyolite pyroclastic unit that overlies a massive rhyolite lava-flow unit. The main breccia pipe begins near the rhyolite/pyroclastic contact, having the shape of an inverted, inclined cone, and consists of silicified breccia, stringers of quartz, and irregular patches of clay-altered country rock. Smaller zones or pockets of hydrothermal eruption breccia are silicified and contain low grade gold in the matrix and in the adjacent silicified wall rocks.   Quartz has been classified according to its physical characteristics as seen in situ and hand specimens indicate that vein definition decreases upwards, perhaps as a result of changing lithological conditions and/or increasing proximity to the paleosurface. Hydrothermal quartz is widespread as veins and as a replacement mineral, or lining fractures and cavities and overgrowing rock fragments. Breccias contain vein quartz, but some quartz veins cross-cut breccias, indicating that vein and breccia formation was relatively synchronous and overlapped in time.   Disseminated gold-silver mineralisation is associated with vein quartz and silicic alteration of the wall rock within the breccia pipe. The auriferous zones are highly irregular and erratic, and sampling results show a wide range of gold-silver ratios, suggesting that highly volatile physiochemical conditions prevailed during mineralisation.

Jan 1, 2005

By G. T. Lapidus, R. M. Luna-Sánchez

In the present study, a series of cyanidation experiments were performed on a bulk sulfide concentrate which contained silver in four distinct phases, to determine its extraction rate, varying the oxygen concentration. The results showed that three of the four phases were refractory, aguilarite (Ag,iSeS) being the only leachable phase, and that the effect of the oxidant concentration is minimal. Mathematical simulations were performed, adjusting only the Damkohler number to adequately fit the experimental data. This model, and the mechanism implied, was compared with that found for acanthite (Ag2S) in a previous study, and the differences between the two discussed.

Jan 1, 2005

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

This paper describes a steam outburst in a metal mine which occurred in December 1992 in Japan, resulting in two fatalities. The outburst occurred just after blasting in a heading face 600 m below surface (SL-50 m), 1664 m from a mouth of the mine. The scale of the outburst was large and the fragments of the outburst spread up to 34 m from the face, the total volume of the outburst was estimated to be 206 m3. The outburst materials were mostly clay originated from the typical surrounding rock of sulfide ore and basalt. The shape of the larger outburst fragments were slabs with a thickness of 10 to 20 cm. The victims were found in a main ventilation air shaft, 175 m and 380 m from the face, respectively. The mine mainly produces copper, lead and zinc. The face was ventilated by a 560 mm diameter duct with a fan and the strata temperature of the rock was estimated to be in the range of 120 to 140¦C. There is a famous hot spring near the mine. A thorough investigation into the unprecedented accident was made including an on-site inspection and investigation of rock characteristics in laboratories.

Jan 1, 2005

By J Zeni

In 2001, the Springvale Coal Mine determined a requirement for a 360 m deep vertical airway to ventilate ongoing underground longwall mining operations. The project, referred to as the Springvale No 3 Ventilation Shaft, was completed in 2003 - 2004 by blind boring a 4.25 m diameter hole from the surface to the coal seam at 360 m depth. The shaft was completed with a 3.5 m inside diameter lining made from a continuous watertight steel and concrete composite pipe. Presented from both the clientÆs and the contractorÆs perspective, the following paper describes the process of constructing a blind bored ventilation shaft for this application. Beginning with the clientÆs definition of the requirements and specifications for the shaft, the paper describes the steps followed by Springvale Coal prior to awarding the contract. Springv aleÆs process involved a thorough site investigation including procurement of geotechnical data for prospective contractors and the management of issues relating to safety, quality and the environment. The clientÆs view is followed by a description of the planning and works performed by their nominated shaft drilling contractor, Ardent Underground Pty Ltd.The contractorÆs description of the works includes the details of the blind shaft drilling and lining construction process used for this application. The design of the shaft lining installed at Springvale Coal was the first of its type to be used in Australia. The successful installation of a watertight composite shaft lining and the safety of the method, which did not require any personnel to enter the shaft or the mine, were among the positive outcomes from the project.

Jan 1, 2005

By D Cioclea, I Toth

Coal mining can lead to the occurrence of spontaneous combustion events. If these events are not prevented they can give rise to fires that have major adverse effects on the mine plan. After studying the chemical structure of coal, the theories of self-ignition and of the oxidation reaction of the organic compounds, two new technologies have been developed for fire prevention based on the inhibition of coal oxidation. The first technology consists of spraying water drops mixed with inhibiting substances into goaves. The second consists of the infusion of a mixture made of several chemical compounds. Tests performed in situ showed the new inhibition technologies to be highly effective even for longwalls mining coal with a high reactivity from the point of view of self-ignition.

Jan 1, 2005

By K. Häge

"Die Nachhaltigkeit der Braunkohlengewinnung in der öffentlichen Wahrnehmung wird nur weiter erfolgreich kommuniziert werden können, wenn durch konkretes Handeln glaubhaft gezeigt wird, dass die offenen Fragen fair und solide beantwortet werden. Dazu gehören insbesondere die neue innovative technische Lösung sowie das sensible Interessenmanagement. Die Braunkohlenindustrie hat gelernt, dass Offenheit und nicht zuletzt das beständige Bemühen um den Meinungsaustausch mit ihrem Umfeld wichtige Elemente sind. Der in Jahrzehnten erworbene Schatz an Glaubwürdig-keit ist eine Basis, auf der die Braunkohlenindustrie ihre Zukunft gestalten kann. Darüber hinaus sind politische Rahmenvorgaben erforderlich. Das öffentliche Interesse an einer sicheren und preiswerten Energieversorgung unter Einschluss der Braunkohle ist unverzichtbar. In diesem Kon-text kann dann die Braunkohle die an sie gerichteten Fragen der Ökonomie, der Ökologie und der Sozialverträglichkeit auch mit Hilfe von Indikatoren beantworten.ABSTRACTThe discussion of the sustainability of lignite mining can only be continued successfully if the indus-try acts in a practical manner and demonstrates trustworthiness by responding fairly and reliably to open questions. This includes new and innovative technical solutions as well as the sensitive management of interests. The lignite industry has learned that openness and the constant effort to exchange viewpoints within their environment are all essential elements. The credibility that has been gained over the decades is the foundation on which the lignite industry can build its future. Beyond that a framework of political guidelines is necessary. Public interest in a secure and inex-pensive energy supply that also includes lignite is indispensable. In this context, the lignite industry will then be able to answer the questions which are directed at them and concern the economy, ecology, and social tolerability also by indicators."

Jan 1, 2005

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

By D. A. Kramer

Ammonia, the principal source of fixed nitrogen, was produced by 16 companies at 31 plants in the United States during 2003. Fifty-five percent of U.S. ammonia production capacity was centered in Louisiana, Oklahoma and Texas because of their large reserves of natural gas, the dominant domestic feedstock. Production In 2004, U.S. producers operated at about 59 percent of their rated capacity. The United States remained the world’s second largest ammonia producer and consumer following China. Urea, ammonium nitrate, ammonium phosphates, nitric acid and ammonium sulfate were the major derivatives of ammonia in the United States, in descending order of importance.

Jan 1, 2005

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005