Search Documents

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005

By J. H. Zietsman

Ilmenite smelting furnaces must be operated with a freeze lining of frozen slag to protect sidewall refractories from chemical attack by liquid slag. The process has two main control objectives: Firstly the slag TiO2 content must be controlled according to specification, and secondly a safe freeze lining thickness must be maintained. This text only concerns itself with the second objective. Freeze lining thickness cannot be measured directly due to conditions inside the furnace. It is therefore inferred from signals of thermocouples installed into the furnace sidewall. These signals are used as the 'controlled variables' in the freeze lining thickness control loop. The dynamic characteristics of these signals are the focus of this text. During this study a model of the process was constructed to study interactions between the slag bath and the freeze lining. This model was used to conduct simulation-type experiments to study the influence of various parameters (temperature, slag composition, ilmenite feed rate, reductant feed rate, power input, etc.) on the slag bath, freeze lining, metal bath, furnace wall and other parts of the process. In the case of the furnace wall, the modelling results were first plotted in the form of time-dependent isotherms. The dynamic thermal behavior of the furnace wall became evident from these results. To illustrate the dynamics of sidewall thermocouple signals, the results were also plotted as time lags between events occurring in the slag bath, and the time when a thermocouple registered a temperature change. The events studied included sudden changes in slag bath state (composition and temperature), changes in operating setpoints (ilmenite feed rate, reductant feed rate, power input), and operational errors (complete loss of reductant or of all feed). All of the result sets showed significant lags between occurrences in the slag bath and temperature changes in the refractory wall. The delays are such that it appears impractical to rely on sidewall thermocouple signals for warning of impending damage to the refractory wall, or for purposes of actively controlling freeze lining thickness. Some measures are suggested to improve the usefulness of these signals during furnace operation.

Jan 1, 2005

By P. Mills

The four top barite-producing countries in the world are China, India, Morocco and the United States. China is currently the largest exporter of barite followed by India. More than 95 percent of the barite mined today is used by the petroleum industry as driller’s mud. The rest is used in the industrial market and the medical field. Most of the barite mined in the United States is in Nevada. This year, mining activity has increased due to an increase in oil exploration/development. This was caused by an increase in the crude oil prices.

Jan 1, 2005

By Anish Kumar

Keywords: Ultrasonic velocity, Poisson?s ratio, Elastic constants A new correlation has been established between two independent elastic properties, ultrasonic shear wave velocity and Poisson?s ratio, in a wide variety of isotropic solid materials, such as pure metals, ceramics, polymers and intermetallics. It has been shown for the first time that Poisson?s ratio decreases with increase in elastic moduli, E & G and ultrasonic velocities. This new correlation between two independent elastic constants may lead to the reduction in independent elastic constants for isotropic solid materials from two to one, at least for a given alloy system with different microstructural conditions.

Jan 1, 2005

By Alexander Malahoff

Six active Kermadec Arc submarine volcanoes located between 34°S and 36°30?S were mapped and sampled by an interdisciplinary inter-institutional research team between April and July 2005 using submersibles Pisces V and Pisces IV aboard the mother ship the RV Kai?mikai-O-Kanaloa. The purpose of the expedition was to study the relationship between hydrothermal activity, formation of hydrothermal mineral deposits and the biodiversity of life associated with the hydrothermal vents. Of the volcanoes examined, all showed evidence of hydrothermal activity, plume production and helium anomalies. Only two of the volcanoes, namely Brothers and Clark, showed chimneys and surficial poly-metallic sulphide deposition. Hydrothermal venting at a water depth of 1700 meters within the base of the northern wall of the summit caldera of Brothers Volcano has produced a field of chimneys, some of them 5 metres high with black smokers venting. Temperatures of 300°C were measured within the active vents. Clark Volcano has a double cone summit at a water depth of 875 metres. The shallowest cone has a near-summit hydrothermal vent field with 5-meter high venting chimneys and smaller structures around the periphery. Water temperatures of 200°C. Geochemical and petrological analysis of the massive poly-metallic sulphide samples taken from Brothers and Clark show a diversity of mineralogy. This diversity is clearly a function of hydrothermal water temperature. Chimneys sampled from Brothers are pyrite and sphalerite dominant with lesser chalcopyrite. Sulphides from Clark Volcano tend to be barite rich with lesser sphalerite and pyrite. Sulphides from Brothers Volcano have a range in gold composition of 4 to 58 ppb with silver composition of up to 38 ppb. A mineral formation model for the volcanoes suggests hydrothermal fluid boiling within the volcanic edifice for those volcanoes with shallow summits and massive sulphide deposition with the edifice as well. Surficial deposits include native sulphur and lower temperature oxides. Only the deeper water Brothers Volcano shows massive sulphide deposition along the marginal faults of the caldera floor.

Jan 1, 2005

By Elli Nurminen

Keywords: Thermal conductivity of sulphates, flash smelting, heat recovery boiler, flue dust Accretions and build-ups in metallurgical heat recovery boilers decrease the efficiency of the heat transfer and may cause process shut downs. Transient plane source method (Hot Disk) has been applied to measure the thermal conductivities of the Copper Flash Smelting flue dusts. Thermal conductivities of copper, iron and zinc sulphates, and process flue dusts were measured. The results indicate that all the components are effective thermal insulators, having a thermal conductivity of less than 1 W/mK. Decreasing dust layer porosity has an increasing effect on thermal conductivity. Insulating layers on the boiler walls decrease greatly the heat transfer efficiency of the boiler. The gathered information will be used in CFD-modelling of the process, and in the process control.

Jan 1, 2005

By W. Dalmijn, H. de Ruiter

"The decline in students for mining and metallurgical engineering in the last few years has lead to the closure of many university departments in all first world countries around the world. Three independent studies carried out in Europe, Australia and North America indicate that during the next decade the demand for mining, minerals processing and metallurgical engineers will be significantly higher than the supply. Demand for engineers will increase even more because many of the professionals in industry are about to retire within the next 5 years. Meanwhile mining is a growth industry, minerals demand continues to increase in line with the growth in World GDP, as illustrated in the Graph at the end of the paper."

Jan 1, 2005

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

A research project was commissioned by the Australian Coal Association Research Program (ACARP) to improve the understanding of tailgate strata mechanics and to provide a more rigorous engineering basis for tailgate support design. A deformation mechanism termed æskew roofÆ was defined which relates the regional influence of differential horizontal strata movement (shear) about longwall extraction to gateroads. Confirmation of the mechanism was achieved by field investigations which included measurement of the shear displacement along weak interfaces. Under geological and mining conditions where the skew roof mechanism operated, strata units were found to move progressively further towards the goaf with height into the roof. 3D numerical modelling was used to assess the major geotechnical factors controlling the mechanism and to determine appropriate support strategies within a æskew roofÆ environment including the role of cables versus standing supports. The skew mechanism is considered relevant to; all roadways in the vicinity of longwall extraction including the faceline itself, chain pillar design, and support design.

Jan 1, 2005

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By Kresho Galovich

Quinsam Coal Mine located in Vancouver Island, BC, Canada is mining the No. 1 coal seam at the 2 North/3 North mine and the No. 3 coal seam at 4 South Mine. This paper describes its geology and structure, mining and processing, development and depillaring practices as well as methods of roof supports under various geological conditions.

Jan 1, 2005

By S. Siddiqua

Diffusion is known to be the main transport mechanism of contaminants in fine-gained soils. To date, it is still common practice to estimate contaminant migration in the Bangkok Clay by means of pure advection models. A series of experiments with various chemical species was performed to determine transport parameters such as the diffusion coefficients and the distribution coefficients. The soil used was saturated undisturbed Soft Bangkok Clay. Column experiments were utilized in a number of laboratory tests involving advective-diffusive migration. Effective diffusion coefficients of different ions were back calculated from the test results. The distribution coefficients were determined from the results of the column tests and batch test. The results indicate that the evaluated parameters are in the range of values obtained from other researchers on similar kinds of soil. Based on this results contaminant migration by diffusion in the Soft Bangkok Clay can now be performed.

Jan 1, 2005

By Dan Brown

This paper provides an overview of the advantages and limitations of continuous flight auger (CFA) and drilled displacement (DD) systems compared to other deep foundation systems, along with a summary of important considerations for selection and design. Geotechnical and project considerations are described which favor the use of CFA and DD piling, and also which may be problematic for this type of construction or which may limit the practicality and competitive advantages. A brief summary of design methods for axial and lateral loading is included.

Jan 1, 2005

By Joseph T. Duncan, Syd Peng, Larry G. Stolarczyk

The mining business has numerous risks: equipment availability, labor disruptions, foreign exchange rate, etc., but one of the more important risks is assessing the geology. Improving the “intelligence” of geology can and will have significant positive effect on reducing mining risk and thus enhancing operational and financial performance. The use of the advanced Radio Imaging Method (RIM-IV) on coal seams and ore bodies can create useful two-dimensional (2-D) and three-dimensional (3-D) high-resolution images that provide mining engineers with additional intelligence to better plan and improve operations. Improved operational performance will reduce costs and enable mining companies to meet market and financial commitments. For the past decade the underground coal mining industry has been moving toward “super panels” in long-wall mining, and “super sections” for room-and-pillar mining. These mining conventions employ wider faces, longer gate roads, greater room-and-pillar density, and an increased scale in the amount and complexity of mining equipment. An obvious economy of scale exists: amortization of setup investments over greater volume of coal enables mine management to reduce fixed cost per ton. Restricted by equipment considerations, face widths have currently reached about 1,100 ft. Wider longwall panels are planned, with 1,400-ft widths, but this requires an incremental step in hardware that the original equipment manufacturers will soon bring to market. However, longwall panel length has not yet reached its limits, with some panels planned up to 25,000 ft. While longwall panel length is generally dictated by reserve size and extent, practical restrictions in mine planning also include seam thickness, ventilation requirements, or restrictions involving methane drainage. Super panels have certainly enabled the industry to keep pushing the limits of productivity improvement. However, important considerations in mine planning, now and especially in the future, will be driven in large part by geological factors. While larger developments improve productivity and capture economies of scale, the fact that super panels can contain at least four times the area or coal volume means that the probability of encountering serious anomalies is at least four times greater than with the “conventional” panels. Given the increased probability of encountering anomalies, improved assessment of geology is important for super panels and super sections. Proper due diligence requires a thorough and competent evaluation of a mining property and its ore reserve. Using improved geostatistical techniques is most important, and improving the base data for the analysis is equally important. The old cliché “garbage in, garbage out” certainly applies. Also, the quality of coal reserves is (or has been) declining, so, in the future, mining will be in deeper and most likely thinner seams—and these seams appear to contain greater anomalies that threaten efficient operations. To counter the impact of reserve deterioration, the industry is moving toward greater use of geophysical tools and services. Fortunately, tools such as the Radio Imaging Method™ (RIM-IV) system have been improved and can provide the industry with enhanced 2-D and 3-D images of coal seams and ore bodies. To identify and profile the best areas of a coal reserve, geologists, engineers, and mine managers need greater intelligence in the form of RIM-IV tomographic maps of longwall panels and room-and-pillar sections. These images have enhanced the understanding of in-seam features, which in turn has improved operational plans and performance.

Jan 1, 2005

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By M Ben, P de Donato, M Kongolo

The extensive literature on sulfide flotation indicates that pyrite poorly floats under alkaline condition. Xanthate concentration has a positive effect on pyrite flotation, but above a pH of 11, pyrite seems to be strongly depressed, independently of the concentration in xanthate. In this investigation, aeration and xanthate concentration effects were studied for pyrite flotation conditioned at pH 11 with lime. Results presented in this paper include surface infrared analyses and pulp chemistry measurements which have showed that aeration had a dual effect on pyrite flotation. It induced pyrite surface activation by oxygen, and oxidation of ferrous iron to ferric hydroxides or oxyhydroxides species. It also favoured dissolution of CO2, leading to calcium carbonate precipitation and adsorption onto pyrite surface. Both CO2 dissolution and ferrous oxidation generated protons and decreased pulp pH. Pyrite flotation was observed to be effective with a statistical monolayer of xanthate that could be adsorbed as mixture of dixanthogen and metal-xanthate complex. Non-floated fractions showed high amounts of carbonate, and presence of hydroxyl iron sulfate (Fen(OH)m(SO4)p, xH2O) which have inhibited the hydrophobicity effect of adsorbed xanthate. Environmental desulfurisation could be improved by aeration control causing pyrite oxidation and pH decrease to reach optimal flotation condition with a relatively low xanthate concentration.

Jan 1, 2005

By Ajay Mahajan, Manoj Mohanty, Vishal Gupta

Modern coal processing plants utilize multiple cleaning circuits to efficiently beneficiate different size coal fractions of run-of-mine coal. An older plant optimization approach is to maintain average product quality from individual cleaning circuits at the same level as the given product specifications for the overall plant. However, many past studies indicate that the equalization of product quality approach fails to produce the maximum plant-yield. A newer approach, known as equalization of incremental product quality, requires that the incremental product quality obtained from each circuit be maintained at the same level to satisfy the overall plant product quality. This approach ensures the maximization of plant yield while satisfying a single product quality constraint. However, while dealing with multiple product quality constraints, this approach by itself may not be sufficient to obtain the desired maximum yield. For the simple reason that the dirtiest particle (or group of particles) with respect to one quality constraint may not be the same particle (or group of particles) with respect to another quality constraint, the mass yield versus product quality relationship generated by equalizing different incremental product quality may not be exactly the same. Therefore, an additional search technique has to be utilized to determine the global-maximum value of plant yield. Thus, the main objective of this study was to utilize an emerging optimization technique, known as genetic algorithms (GA) to maximize plant yield while satisfying multiple product quality constraints. The maximum plant yield obtained from this approach was nearly same as the maximum yield obtained by the incremental product quality approach while satisfying one specific product quality constraint. The GA was applied on a coal preparation plant that utilizes four circuit operations - heavy medium bath, heavy medium cyclone, spiral and froth flotation. The results showed that using GA as an optimization process gives 2.56% higher yield that will result in additional revenue generation of $5,120,000 per annum than average product quality approach.

Jan 1, 2005