Search Documents

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By I. Fafoutis

Laboratory column studies were conducted in order to assess the effectiveness of slag and red mud reactive barriers for cleaning up leachates generated at mining and waste disposal sites and loaded with copper and manganese. Solutions containing the metals of concern were prepared by dissolving the required quantities of CuSO4?5H2O and MnSO4?H2O in distilled water so that Cu concentration was 100 ppm and Mn 20 ppm. Flow rates of 25 mL.h-1 for Cu solution and 75 mL.h-1 for Mn solution were used in order to simulate aquifer water velocities of 1 ft/d and 3 ft/d respectively. Solutions were pumped upflow, in Plexiglas laboratory columns filled with each reactive medium, using peristaltic pumps. Measurements of middle and outflow column pH, redox potential, conductivity and elements concentration were performed to provide information regarding removal mechanisms for both elements and exhaustion/inactivation rates for each reactive medium. Both reactive media showed fairly good removal efficiency over the period studied. Copper was mainly removed by precipitation and formation of Cu(OH)2 while removal of manganese was due to precipitation of Mn(OH2).

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By A. V. Tarasov

Regeneration of carbide waste from hard-alloy (sintered carbide) manufacture is an important scientific and technical objective aimed at improving the degree of recycling of rare metals (W, Co, Ta, Ti, Nb). Currently, the degree of recycling of those metals does not exceed 25% to 35% of their total production even in industrially developed countries. This is attributed to a significant extent to the substantial drawbacks of the technologies applied for their processing (environmental pollution, limitations to the use of regenerated products for important applications, sophisticated equipment to be used). An innovative environmentally sound technology has been developed in the Institute of Metallurgy of the Russian Academy of Sciences (IMET RAN) for processing of carbide waste of WC, TiC, TTC and other carbides using asymmetric alternating current of industrial frequency (the electrolyte used for this purpose is nitric acid solution). The current efficiency under optimal conditions is as high as 96% to 98%. The process has been tested on bench scale. The following commercial-grade products are obtained: pure ammonium paratungstate, tungstic acid, cobalt oxide, titanium dioxide and tantalum-niobium concentrate. The total metals recovery is 98% to 99%.

Jan 1, 2006

By E. Özberk

Uranium minerals are often associated with iron minerals, and during the hydrometallurgical processing of the uranium ores, iron plays several significant roles. The presence of Fe(III) in solution promotes the oxidative acid leaching for the recovery of uranium. The control of the distribution of impurities in milling and refining is also affected by dissolved iron. When rejected from the process streams, iron usually collects other impurities and contributes to the stabilization of the wastes for final disposal. These roles of iron, as they relate to current uranium processing operations, are discussed in detail, and some broad and historical perspectives are also presented.

Jan 1, 2006

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Jae-Woo Ahn

Waste acids containing phosphoric, acetic, nitric and hydrofluoric acid were produced during the etching process of liquid crystal display and semiconductor manufacture. In recent years, the attention on the treatment of industrial waste acids has been increased considerably according to the reinforcement of the environmental regulations as well as the implementation of the economic considerations about the waste acids. Fundamental studies on the separation and regeneration of the mixed waste acids were conducted using Cyanex 923, Tri-octyle phosphate and 2-Ethylhexyl alcohol as an extractant by solvent extraction. It is considered that the extraction of liquid crystal display waste acids with Cyanex 923 and Tri-octyle phosphate, semiconductor waste acids with 2-Ethylhexylalcohol is applicable for the separation and recovery of acid. Finally, the acceptable recycling process from the multi-component waste etching acids was proposed.

Jan 1, 2006

By D. J. H. Walker, W. H. Gibson

The inclination of any pit wall composed of stacks of benches is limited by the overall quality and structural complexity of the rock mass in which the slope is situated. For a bench stack angle that satisfies the stability criteria, various combinations of bench height, bench face angle and berm width can be used in the slope design. The bench face angle and berm width geometries must be chosen to fit the bench stack angle but must provide a berm that will be capable of catching the volume of failed wedge material from the bench faces above. Other considerations for bench height and berm width are equipment size, ore selectivity and blasting design. This paper studies the effects of different slope configurations on slope performance as it relates to wedge stability, volume of rock safely contained on berms, and rockfall. Optimisation of the geometry is carried out based on the need to minimise the volume of failed material which limits the effectiveness of the berm. This will reduce the number of rocks that can continue to fall further, reaching geotechnical safety berms or pit ramps, that put safety of personnel and equipment at risk. For general study it is most effective to investigate and compare the performances of each of a wide range of geometrical combinations of bench height, bench face angles and berm widths that fit a variety of different bench stack angles. These analyses were conducted for a predetermined bench stack height and three different bench stack angles.

Jan 1, 2006

By Jonathan A. Paul

The most profitable companies in the world recognize that a huge competitive and financial power lies in their intangible assets. The competition to be in command of raw materials and markets is now waged more and more over the exclusive rights to new technology and ideas. The value gained from mining the innovation in your organization and protecting your intellectual property can be enormous. This paper will address the following topics: ? Understanding the connection between your competitive position and intellectual property ? Determining the value of your current portfolio and strengthening protection ? Converting knowledge into assets and adding value to the operation ? Litigation strategies to enforce your position and achieve your business objectives The presentation is designed for company executives and government managers who need to know how to identify and address core intellectual property issues that arise in the minerals, metals and materials extraction and processing industries.

Jan 1, 2006

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By P. Sotiropoulos

In the framework of the Specific Programme: ?Promoting Competitive and Sustainable Growth? a detection system was designed and developed in order to provide an added value service beyond standard instrumentation. In the hydrocarbon industry it will be possible for the first time to detect in a pulse regime, two types of radiation emissions using a single device. This means that any saturation of hydrocarbons can be detected, irrespective of the degree of formation water mineralization, which is a major limitation on currently available neutron-gamma tools, where the formation water has a low mineralization.

Jan 1, 2006

By Min Xiaobo

As for treatment of zinc-containing wastewater, traditional SRB (Sulfate Reducing Bacteria) process was used, however, there exist two defects, like toxicity of heavy metal ions and high effluent COD (Chemical Oxygen Demand) value. In this study, a new technique, called ISIS process (Immobilized SRB sludge beads with Inner cohesive carbon Source), in which SRB sludge is embedded in carrier of PVA (Polyvinyl Alcohol) with carbon source that adsorbed on certain material, is put forward for the first time to overcome the two defects existing in traditional SRB process. Furthermore, it has been shown that compared to traditional SRB process, ISIS process increases average zinc removal rate up 30%, average sulfate reduction rate up20%, and decrease average effluent COD value to meet discharge standards. If activated carbon is selected for carbon source adsorption and fixing material, and PVA for immobilization material, the zinc removal rate can reach above 98% under the conditions of 35 and pH 6. Meanwhile, the mechanism of zinc removal has been determinated according to the results from SEM (Scanning Electronic Microscope) and XRD (X-Ray Diffraction).

Jan 1, 2006

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By M. Potesser

In the primary and secondary copper industry the anode furnace is the most important process step in the refining procedure to reach an enhancement in value and quality of the copper by a selective oxidation and reduction. By combining the advantages of the conventional tilting hearth anode furnace and the benefits of the drum type anode furnace a new aggregate was developed and patented. The cross-section of the furnace is elliptical and the whole unit is tiltable. During the melting period, the contact surface between the burners and the bath or the scarp is enlarged - an increased energy input is the consequence. For the refining period the furnace is rotated, whereby a high bath level is guaranteed. Due to the longer residence time of the gas in the copper melt, not only the gas consumption is reduced but also the efficiency/quality of the refining process is improved. This investigation shows a metallurgical comparison between the new anode furnace concept with the elliptical profile/cross section and the conventional, tiltable hearth anode furnace as well as the drum type anode furnace. The CFD modeling of the currents in these different furnaces delivered helpful data to compare the geometry of the different furnaces. The investigation covered the refining of blister copper from primary metallurgy, from secondary metallurgy as well as from a mixture of both copper melts. The paper underlines the possibilities for a reduction of the tap-to-tap time and for an increase in production capacity, which can be achieved by applying the new furnace concept in comparison to the conventional furnaces.

Jan 1, 2006

By W. Keilich

A methodology of subsidence prediction using the Distinct Element code UDEC has been developed as an alternative for subsidence modelling in the Southern Coalfield, New South Wales, Australia. The models have been validated by comparison with empirical results and observed caving behaviour. At this stage, modelling capability is limited to flat lying terrain. It is planned to apply the methodology to areas of high topographical relief to investigate the mechanics of valley closure.

Jan 1, 2006

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By Dallas Grubbs

Agenda ?Growth Projections ?Economic Indicators ?Mining Equipment Growth ?Tire Supply ?Michelin Actions to Increase Capacity ?Michelin?s Challenges & Recommendations

Jan 1, 2006