Search Documents

By John J. Sammarco

This report (Safety File Guidance 6.0) is the eighth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [5.1System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By D. R. Tesarik, F. M. Jones, J. B. Seymour, L. A. Martin, T. J. Williams

Determining backfill stress is an important part of evaluating mine safety, whether personnel are working in proximity to backfill or in other areas of the mine where backfill is an integral part of regional support. To assist in determining stress in backfill more accurately, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Placer Dome, Inc. (Turquoise Ridge Mine), Peabody Energy Co. (Foidel Creek Mine), and Hecla Mining Co. (Lucky Friday Mine) used temperature readings recorded by thermistors to correct for the influence of temperature on stress data. These thermistors were positioned in the stems of earth pressure cells installed in backfill. Corrections were then calculated and compared using four different methods: polynomial equations fit to temperature-versus-stress plots before the pressure cells were loaded by overburden, a factor provided by the manufacturer, a theoretically derived factor, and a linear correction factor based on information collected during periods when no mining was taking place. To evaluate the accuracy of these methods, corrected stresses were calculated using each method and results compared to cumulative stresses caused by blasting at one of the mines. Results indicated that only a small percentage of the temperature effect on stress was corrected using the factor from the manufacturer because that factor accounted for only the pressure transducer and not the entire instrument body. Stresses adjusted with a linear correction factor based on information collected during periods when no mining was taking place were the most accurate. Stresses recorded at two other mines were corrected using the theoretical method and the polynomial equations method; the two methods produced similar results. For some time intervals, the results were identical.

Jan 4, 2006

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By Elaine Cullen, Launa Mallett, Mike Jenkins, C. M. K. Boldt, Thomas Camm

The material in this Information Circular was presented at the National Institute for Occupational Safety and Health’s (NIOSH) open-industry briefing held during the 2004 Northwest Mining Association conference in Spokane, WA. The open-industry briefing discussed results of recently completed and on-going mine safety- and health-related research conducted at NIOSH’s Spokane and Pittsburgh Research Laboratories on the human side of mining—the miner. The first paper sets the stage for what mining has achieved and what we mean by “getting to zero.” The second paper, “Help Experienced Miners Become Great On-the-Job Trainers,” distinguishes between experienced miners and trainers. This paper provides some key concepts for turning great miners into great trainers. “The Power of Story-Telling in Getting Through to Miners” explains the history and importance of stories in the culture and training of miners. Finally, “Understanding Self in Stressful Working Environments,” describes the personal and social aspects of the working environment, much of which parallels familial theories. The downward trend of deaths in U.S. mining has been remarkable. The number of miners killed or injured each year has decreased steadily over the past 100 years. Some charts show these trends overlain with important events such as World War II and the Mine Safety and Health Act. However, this downward trend in mining fatalities has flattened out. How can you get to zero accidents? Do you concentrate on technological advances and equipment maintenance to avoid malfunctions? Do you concentrate on developing work processes and organizational structures that minimize risk? Do you combine them and take a systems approach that links one to the other with an evaluative loop? Safety efforts in mining have used all of these approaches. What more can we do to get to zero? Getting to zero will require two objectives: A clear and unshakeable belief that it can be done and attention to the human side of mining. Getting to zero is not a new idea; it has been used by mine companies and safety professionals for years as the safety goal. But getting to zero is not so much a physical goal as it is a belief that there are no insurmountable barriers to achieving the goal.

Jan 3, 2006

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of light-scattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2006

By E. Nejati, S. Khoshkooei, V. Firouzdor, M. Akbari, F. Khomamizadeh

In this study the effects of Si content on mechanical and thermal fatigue properties of Al-Si casting alloys were investigated. Repeated heating and cooling cycles were applied on the samples at 230°C to develop thermal fatigue cracks. Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy. Thermal fatigue behaviors were improved successively by increasing of silicon content up to 7wt%. However, addition of more than 9wt% silicon decreased the thermal shock resistance of the alloy. Silicon contents of about 9wt% presented the best mechanical and thermal fatigue resistance in the alloy.

Jan 1, 2006

By J. A. Jr. Carpenter

Expanding world economic prosperity, probable peaking of conventional petroleum production in the coming decades and environmental concerns require efforts to increase the efficiency of, and the development of alternatives to, petroleum-based fuels used in automotive transportation. In January 2002, the U.S. Department of Energy (USDOE) and the U.S. Council for Automotive Research (USCAR) of the "Big Three" traditionally-USA-based automakers, DaimlerChrysler, Ford and General Motors, formed the Freedom Cooperative Automotive Research (FreedomCAR) Partnership to fund high-risk, high-payoff research into advanced automotive technologies with the potential for eventually lowering the USA&apos;s nearly complete (95%) dependence on petroleum, 55% imported, for its transportation fuels. FreedomCAR replaced the Partnership for a New Generation of Vehicles (PNGV) which existed from 1993 to 2001. In January 2003, the energy-supply industry joined with the FreedomCAR Partnership forming the FreedomCAR and Fuel Initiative (FC&FI) to develop the technologies needed for the mass production of fuel-cell vehicles using hydrogen as fuel and the infrastructure needed to deliver the hydrogen to the consumer. The goal is to enable the automotive and energy-supply industries to make commercialization decisions in 2015 on large-scale introduction of such vehicles and on developing the infrastructure beginning in 2020. In addition to work on fuel cells and hydrogen infrastructure, the FC&FI conducts research on technologies with the potential for nearer-term energy efficiency and environmental benefits, such as new engine concepts, lightweight materials, and engine-electric hybrid propulsion systems. Lightweighting is seen as crucial for shorter and for longer term benefits because hybrid and fuel-cell powertrains are expected, at least in the early stages of adoption, to be heavier and more costly per unit of power than the standard internal-combustion, gasoline- or diesel-fueled powertrains they replace. Research and development (R&D) on casting of aluminum automotive components were major parts of the PNGV and R&D on casting of magnesium automotive components have been and are so under FreedomCAR. This presentation will review those efforts.

Jan 1, 2006

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

Caterpillar said it will produce a Cat line of ac electric drive mining trucks. The world’s largest manufacturer of mining and construction equipment said the addition of an AC electric drive truck line will provide its customers with products to fit key applications. “We are very proud of the strong leadership position that Caterpillar has attained with its mechanical drive trucks, and we will continue to invest in strengthening that position,” said Chris Curfman, president of Caterpillar’s Global Mining Division and Caterpillar Inc. vice president. “We also recognize that there are unique applications that would make the addition of ac electric drive an important and attractive complement to our current truck line.” This is the largest investment Caterpillar has made in mining trucks in its history.

Jan 1, 2006

By Jannie S. J. van Deventer

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push towards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Geopolymers derived from coal ash can exhibit superior mechanical properties and chemical stability when compared to ordinary Portland cement (OPC). The use of waste-based geopolymers can also result in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the encapsulation of mine tailings, immobilization of heavy metals and back-filling of mines due to their chemical stability and resistance to acid attack. A key attribute of geopolymer technology is the robustness and versatility of the manufacturing process; it enables products to be tailor-made from a range of raw material sources (waste and/or virgin) with specific properties for a given application at a competitive cost. Despite these key technical and environmental attributes, it is the ability to add significant value to coal ash or and/ or metallurgical slag waste streams which drives the commercial development and uptake of the technology.

Jan 1, 2006

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By Pinakin Chaubal

An analysis of the blast furnace and the low-pressure shaft DR furnace is carried out by redefining the reaction zones. The concept of a characteristic reaction gas temperature (CRGT) is introduced and the two reactors are compared and contrasted using some recent process developments with an aim to develop a platform for further synergistic innovations.

Jan 1, 2006

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006