Search Documents

By Andrew K. hg` Officer, A. L. Griffiths, J. Andrew Hindmarch, Gert Wittneben

Durban Harbour in South Africa is one of the continent’s busiest ports however the harbor entrance is currently too small for the new generation of container ships. There-fore it is to be deepened and widened by the National Ports Authority in the near future. An existing immersed tube tunnel carrying major sewer, water and other utilities under the harbor first needs to be removed and replaced by a deeper 4.4 m ID ser-vices tunnel. Construction of the deeper tunnel saw the first use of a slurry machine in South Africa and was required to negotiate grades up to 20%.

Jan 1, 2007

By Emad Farouz, Roger Failmezger

"The proposed reconstruction of I-75 downtown consists of widening an approximately 2.46 Km section of IR-75 through the northern section of downtown Dayton, OH, USA. Bridge B-13 is a 9-span continuos prestressed concrete I-beam, 319.0-meter (1,048-foot) long bridge with a stub abutment on MSE walls for the rear abutment, and a stub abutment with spill-through slopes for the forward abutment. The piers in the river were located parallel to the Great Miami River, and are full-height reinforced concrete wallsPRESSUREMETER TEST PROCEDUREThe driller advanced either casing or augers approximately 1 meter above the pressuremeter test. Steel casing was used to advance borings performed in the river, and augers were used for borings on land. Mud rotary drilling with a large diameter roller bit was used to remove all of the gravel and cobble fragments inside the casing or augers.At the pressuremeter test elevation the driller used a 63.5-mm (2.5-inch) carbide button bi-cone bit, using a rotation rate of about 60 rpm, a mud fl ow rate of about 10 gallons per minute (40 liters per minute), and an advance rate of 6 to 10 minutes per meter (2 to 3 minutes per foot). To minimize vibrations, advance rates were slower where excessive cobbles were encountered. The 63.5-mm (2.5-inch) O.D. slotted casing pressuremeter was lowered to the test elevation, often requiring either pushing or hammering into the test zone. We believe that the test zone was not perfectly straight, or that gravel or cobble fragments jutted into the test zone and had to be displaced to advance the pressuremeter into the test zone. The slotted casing prevented membrane damage during insertion. A photograph of the slotted casing being lowered into the borehole is shown below.The pressuremeter was calibrated for system compressibility and membrane resistance. At full expansion of 800 cm3, the membrane resistance of the slotted casing was about 2.5 bars.Strain-controlled tests were performed using a Texam control unit with a monocell probe. Volume increments of 20 cm3 were injected into the probe and corresponding pressures were measured. Near the end of the elastic portion of the test, an unload-reload cycle was done. A creep test was performed for 10 minutes at the next volume increment. The test continued until either 800 cm3 were injected or the membrane burst."

Jan 1, 2007

By C. Phan

This paper outlines opportunities provided for enhanced management and process control by ISA PROCESSTM technology. ISA PROCESSTM technology has the core advantage of offering the potential for vastly improved electrode handling systems. This fundamental characteristic has enabled ISA PROCESSTM technology to develop management and process control systems that are modular, minimalist in their complexity and tailored to a tankhouse operating environment. A review will be presented on the current status of management and process control in ISA PROCESSTM tankhouses covering the central issue of electrode handling as well as electrolyte circulation systems, voltage monitoring, cathode plate tracking, and product tracking. Particular reference will be made of the recent development by Xstrata Technology (XT) and their technology partners, VRT Systems, of an Radio Frequency Identification (RFID) based solution for tracking ISA PROCESSTM cathode plates. The system encompasses fixed readers which identify plates passing through the stripping machines and the use of sophisticated tracking and database software enabling the development of cathode asset management and operational strategies. The performance of individual plates and batches of plates can be tracked through a full service history.

Jan 1, 2007

By R. G. B. Pickering

The South African narrow reef hard rock mining industry has been stuck in a time warp with relatively little change in the mining process in the last century. This paper presents a methodology on how to implement change in narrow reef hard rock mining. It then explores a number of technologies that have been introduced into this mining industry and the impact that they have had on the mining process. The author then presents his view on whether the defined change process has been followed and sets out to identify the most critical aspect of ensuring that change is successfully implemented. Future demand will also be speculated on.

Jan 1, 2007

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By J. Roufagalas

Sustainable development requires that exploitation of environmental resources is such that it does not result in permanent damage to the environment. In many instances environmental damage is an external cost of the entity exploiting the resource. Ideally, the entity should be forced to internalize this cost. Various financial assurance schemes have been proposed to ensure that the entities fulfill their financial responsibility to restore the environmental dam-age. Prominent among these schemes are ?environmental bonding requirements?. A main issue with these financial assurance schemes is that many times the amount and duration of environmental damage is uncertain. That is, the cost of restoring the environment in the future may be unknown (or unknowable), and, furthermore, the extent of the damage may not be known for many years into the future. Nevertheless, bonding requirements have to be set in advance and the rules for returning the bond and absolving the entity of responsibility have to be specified ex ante. In practice, a problem of allocation of resources arises. To make sure that all external costs are internalized, in the face of uncertainty, will require a sufficiently (arbitrarily) large bond for a sufficiently (arbitrarily) long period of time. But such a requirement may prove too expensive and may result in not undertaking a project (even if, under certainty, the project may be profitable after internalizing all costs). This will result in a reduction in total welfare. Under present bonding requirements, firms are responsible up to the value of the bond. This results in an asymmetry: if environmental restoration is less than the bond amount, the firm has an incentive to restore and reclaim the bond; if the cost of the environmental restoration is above the value of the bond, the incentive is to forfeit the bond, imposing on the government/ society the excess cost. This also may reduce social welfare, at least on distributional grounds since the firm owners pocket the profits and the taxpayers foot the bill. The presence of uncertainty suggests that a fee based reclamation fund may be welfare enhancing. The thinking can be sketched as follows: All firms undertaking environmentally sensitive projects pay into the proposed fund. The fund examines the risks and sets the premiums at the level of the expected restoration costs (not the maximum!) plus administrative expenses. One advantage of the scheme is that this eliminates the asymmetry. Firms with restoration costs below expected end up subsidizing firms whose restoration costs were underestimated. In other words, the industry ends up internalizing the costs not internalized by the individual firms, instead of the taxpayers.

Jan 1, 2007

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By U. Heuer, B. Rathmann

Many mining operations have gained an impressive expertise in trouble shooting and maintenance with their existing fleet over the years. Whether it is an in-house maintenance group or an external service group - most of the systems weak points are well known and can be corrected by maintenance personnel. As some of these issues get more and more serious each year, too much time is lost in unscheduled downtime, often taking hours to be repaired and to find the failure with obsolete diagnostic tools (Fig. 1.). Many of the breakdowns result from failures that cannot be detected in advance. The maintenance system is much more reactive than preventative. The state of the art of mining equipment today uses advanced, efficient, and reliable systems for electrical drives, control and diagnostics of the machines. The demand for highly sophisticated solutions on such mining equipment is well known. Mining operators need to ensure the highest level of productivity, lowest operating costs, least maintenance and highest reliability in a drive system. The paper will introduce you to the state of the art of drives technology for dragline (Fig. 2) and shovel mining equipment (Fig. 3).

Jan 1, 2007

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

By A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate, while increasing it decreased the corrosion rate. Keywords: austenitic stainless steel, % ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentio-dynamic scans, microstructure, chemical analysis.

Jan 1, 2007

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007

By G. Récoché

For the African continent promoting a sustainable utilization of its mineral resources could be considered as a key determinant to fight against poverty. Sustainable development performance indicators for measuring the economic, environmental and social impacts of mining activity are necessary for drawing up policies and sectoral actions, identifying and controlling risks, identifying and implementing sustainable development actions, negotiating between stake-holders, improving mine production, etc. To respond to this need, the SIGAfrique Network proposed to develop a joint decision support tool entitled the African Mining Observatory (AMO) and, to this end, develops a system of indicators to be integrated within the SIGAfrique database. The development of both the OMA and the indicators is based on a participatory method within the working groups, which comprise experts/participants from the 13 SIGAfrique partner and observer countries (Guinea, Burkina Faso, Mali, Tanzania, Niger, Mozambique, Kenya, Uganda, Senegal, Angola, Madagascar, Ethiopia, and Mauritania).

Jan 1, 2007

By R. Ramirez

Atlantic Copper Refinery (Huelva, Spain) has operated the ISA permanent cathode technology since 1995. The current production rates are 260,000 t/y cathodes and 730 t/y anode slimes. These slimes undergo an atmospheric leaching in which their copper content is reduced from an average value of 24 % to 16 %. In June 2005 an optimization study of the leaching conditions was carried out aimed at lowering the copper content in the slimes to less than 8%. At the same time, a new mixer (Outukumpu Technology GLS-mixer) was installed in one of the three leaching reactors. As a result of the improvement of the leaching performance and to prevent the return of tellurium to the tankhouse, a cementation plant was commissioned in July 2005 to ensure a Te content below 50 ppm in the Cu-rich leachate. This paper describes the results of the improvement of the leaching conditions and the operation of the new tellurium removal plant.

Jan 1, 2007

By R. von Gal

Hazelett Strip-Casting Corporation has been producing the Hazelett® twin-belt casting machines for copper casting since the mid-1960s. The first commercial casters were developed for copper alloy strip and anode plate. In 1968, development work was started to adapt the twin-belt caster for copper bar casting to be rolled in-line into wire rod. Since then, 36 casters have been sold as part of the CONTIROD® system for the production of a substantial portion of the world's copper rod supply. A unique feature of the twin-belt caster is the mold's ability to comply with the size and shape of the cast bar as it shrinks during solidification. Maintaining contact between the mold and the bar provides a high rate of heat transfer as well as other benefits, including the prevention of surface imperfections caused by remelting in the mold. This paper will give an overview of the continuous evolution of the twin-belt caster technology with an emphasis on recent developments in compliant mold technology for copper casting.

Jan 1, 2007

By W van Drunick, S Naik

To date, Anglo Research has carried out several projects, based on the techniques developed in the AMIRA P9 (AMIRA International Limited), to develop comminution and flotation models for several Anglo Base Metals and, to a lesser degree, Anglo Platinum flotation plants. Plant optimization is thus achieved through steady-state sampling, model-fitting and simulation using the JK SimMet and JK SimFloat software packages. The surveys can vary depending on the needs of the plant/client. The survey can therefore include as little as a single piece of equipment, an entire milling/flotation circuit, or a complete circuit from primary comminution to final flotation concentrate (i.e. the ?integrated survey?). The presence of the AR team on-site usually precipitates in face-value observations that can lead to initial improvements. This stems from the knowledge-sharing on best practice that exists in parallel with the surveys. Numerous (reasonable) changes can then be simulated, thus indicating the optimization step most likely to result in the best efficiency improvements. The simulations can include changes in the flowsheet, ore characteristics, mill loads, grinding media size, change in grind, flotation residence time, air hold-up and several more. Plant surveys can result in process changes that provide the plant with either: higher plant tonnage, improved plant grind, additional flotation recovery and/or improved product grade. The additional benefit of performing an integrated plant survey is that the effects of an optimization change in the comminution circuit can be simulated using the flotation model. This paper describes a number of case studies where individual and integrated plant surveys were conducted by AR for Anglo Base Metals.

Jan 1, 2007

By William Yutmeyer, Meredith Hardwick

Since 1996 there have been at least two teams formed within the U.S. Government to develop a consistent set of risk-based standards to be used to govern safety. The first of these was the Risk and Lethality Commonality Team which developed risk criteria associated with protecting personnel during launches at the national test ranges. The second team titled the Risk-Based Explosives Safety Criteria Team (RBESCT) is the subject of this paper.

Jan 1, 2007

By M. Zhang, M. Menabde, R. Middleton

Whilst mine planners almost universally assume deterministic forward commodity prices when undertaking valuations of mining projects, historical data well demonstrates that those prices are quite volatile. This paper seeks to understand and quantify how this forward price uncertainty will impact mining project valuation. This paper will also present a way of computing an upper bound on the expected Net Present Value (NPV) of a mining project given forward commodity price uncertainty.

Jan 1, 2007

By Jim Daly

The word “Enron” has taken on a totally different meaning since its leaders were caught juggling the books, President Clinton’s reputation was destroyed not by what he did but by how he tried to cover it up, Martha Stewart spent time in prison for not being honest. Our society is tolerant of mistakes we humans make but has become very critical about what we do following those mistakes. The blasting industry is in a similar position. We have all heard the stories of the tree stump that came down through someone’s roof, of the windows that were broken, of the casualties that occurred when a blast was not properly guarded. What was done following these incidents? In the mind of the public, not enough.

Jan 1, 2007