Search Documents

By N. Saldía, C. Riveros, R. Hills, S. Barrera

The transport of tailings composites provided by different sources is a field of study where a limited amount of research has been conducted. Nevertheless, such systems are important sources of operational difficulties, especially in the case of high clay content tailings. The case presented in the present paper consists of a free surface flow pipeline transporting a composite of two different tailings with high clay content. It has presented operational difficulties such as partial blockages and upstream box and air intake overtopping events. In the present paper, the causes of these difficulties are identified. These include lack of complete mixing of the different tailings, multi-layered flow with low velocity and high yield values with high frictional losses. The pipeline characteristics and performance are analysed in three stages: design, initial operation and enhanced operation, the latter accomplished by means of increasing turbulence in the box located upstream from the pipeline. The last section of the pipeline and another distribution pipeline system located downstream from the pipeline have performed well. The cause of different behaviour of both systems is also assessed.

Jan 1, 2007

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By J. Nelsen

Social License to Operate continues to emerge as a paradigm fundamental to sustainable mineral resources development. It relates to a set of concepts, values, tools, and best practices that represent the view of reality held by each participant (industry and stakeholders). It enables a forum for negotiation through which all parties involved are heard, understood and respected. The exploration phase of the mine life cycle is generally the initial contact with local communities and forms the cornerstone for effective communication and trust building. This paper presents the development of a mineral exploration template, based on field studies, aimed at assisting exploration personnel to establish effective communications and engagement with local communities within a process to build a Social License. The template aims to provide practical assistance in conducting situational analysis - a process of examining and mapping a situation, its elements and their relations - in order to acquire knowledge and understanding of a project, locale and region. Situational analysis is the ?full situation of inquiry?, going beyond just ?knowing the subject? to being fully situated. It forms the initial foundation for a planning process presented in the paper that prepares for a strategy of initial engagement and consultation.

Jan 1, 2007

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007

By R. Graeme, J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona Project, located in Hualgayoc, Cajamarca Department, Perú, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, Project development occurred against the backdrop of a Presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as unprecedented demand for engineering and technical skills. Project “Lessons Learned” are outlined and discussed in the context of an evolving strategy.

Jan 1, 2007

By F. T. Cawood

This paper focuses on the role of the coal mine surveyor at the start of the 21st century. It demonstrates that surveyors must look beyond their legal appointment and pursue opportunities to add value at an operational or corporate level of the company. It also exposes the shortfall of statutory appointments in defining the surveyor?s role in terms of key business drivers of the company. One such an opportunity is the potential role of the surveyor in mineral accounting and quality assurance to meet mine requirements, market specifications and standards pertaining to corporate governance and reporting. Finally, some thoughts are expressed on what can be done to elevate current practice to best practice and how to achieve this goal

Jan 1, 2007

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By K. Krishnapisharody, S. Clark, M. Barati

Different gas purging methods to metallurgical baths have been applied to date, among which are top lancing and bottom blowing through tuyeres or porous plugs. Among these, the porous plug bottom blowing technique has shown higher efficiency in gas utilization than tuyeres and top blowing, due to smaller bubble size and lower liquid velocity. However, the studies related to bottom stirring of metallurgical baths are limited to slag-less or thin slag-covered melts. In particular, there is no examination of stirring ability in conditions similar to Falconbridge's Slag Make Converter, where the bath is covered with a thick slag layer and a stream of solids is charged on the bath from top. This study was undertaken to investigate the application of gas purging through a porous plug in stirring in and melting of the solid feeds. The spreading behaviour and melting time of a solid layer forming on a plume created by stirring were calculated using the existing models. The results show that formation of a thick solid layer, specifically in areas beyond the plume region is very likely. Nevertheless, the thickness of the layer and melting time do not appear unreasonably high. It is predicted that by proper controlling of gas flowrate and plug configurations, successful solid charging through the mouth can be practiced.

Jan 1, 2007

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By G W. Scott, R C. Johnson

Hypogene alteration zones have been described as a precursor to high-grade haematite deposits in Australia, Brazil and elsewhere. This alteration is described as being below or distal and is typically magnetite-carbonate-silicates reflecting Mg - Fe metasomatism. This paper describes, without genetic implication, the mineral zonation and possible structural control on mineralogic variation within the Tilden Mine, a concentrating grade haematite deposit in Michigan, USA. In contrast to the high-grade deposits, these variations are not peripheral to the orebodies but are the ore. The deposit occurs within the Negaunee Iron Formation, along the southern margin of the Paleoproterozoic Marquette Range Supergroup basin. The regional structure is a fault-bounded west plunging syncline within the crustal scale Great Lakes Tectonic Zone, which forms the boundary between Archean granite-greenstone and gneissic terranes. Local structure consists of second-order anticlines and synclines with variable northwest and southwest plunges. The interaction of sedimentation and diagenesis within growth fault controlled basins, along with a possible metamorphic and/or hydrothermal overprint has resulted in a complex series of ore types. For modelling purposes, the deposit is divided into geologic domains based on both lithology and metallurgical response in the laboratory and in the plant. Mineralogic variation is recognised within individual mineral grains; at blast pattern (10 - 15 m) and development drill hole (100 m) scales.

Jan 1, 2007

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By A. D. Thomas, K. C. Wilson

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sub-layer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By understanding the ore breakage characteristics and utilising comminution circuit modelling, the benefits of SAG mill feed size manipulation can be readily assessed. This paper looks at the benefits and problems of total secondary crushing of mill feed and advocates partial secondary crushing as a means of improving grinding efficiency for certain hard ores. Case studies are reviewed for new and existing SAG mill circuits.

Jan 1, 2007

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in1983 with the formation of De Beers Marine. Full-scale commercial mining commenced around 1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geo-survey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. DeBeers operates across the entire value-chain spectrum from geology and geo-survey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in DeBeers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities are also available to support R&D and projects activities. Hydro transport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet-pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By H. Walqui, G. Rajala, G. Suardini

The Empire mine began operations on 1963. Low grade Magnetite ore is processed to produce iron pellets for blast furnace feed. Three expansions were added to the original plant and several equipment upgrades have been completed to improve the plant performance as the ore characteristics have been changing through the life of the mine. Size reduction is carried out by two grinding stages, the first one using autogenous grinding and the second one using pebble mills. Pebble crushing is also used to break the critical size fraction and increases primary grinding capacity. This paper describes changes in the configuration of the grinding circuits that have helped increase plant throughput and reduce power consumption by more efficiently utilizing assets available. Understanding the different components of the size reduction circuits and plant sections has allowed shifting part of the load from one section of the plant to another without affecting plant throughput.

Jan 1, 2007

By K. C. Sole

In most copper solvent-extraction operations, an important consideration in choice of extractant is the requirement for high selectivity of copper over iron. Ester-modified aldoxime extractants presently offer the best Cu:Fe selectivity. In some plants, however, the process feed liquors contain significant amounts of manganese but little iron. Although manganese is not chemically extracted by oximes, trace amounts are carried over to the electrowinning circuit by physical entrainment. This may result in anodic oxidation of manganese which, in turn, can cause oxidative degradation of the organic phase when returned to the solvent-extraction circuit in the spent electrolyte. Many of these operations prefer to operate with higher levels of iron reporting to the advance electrolyte, as appropriate control of the Fe(II)/Fe(III) couple will ensure that manganese remains in the benign Mn(II) form. A new reagent, LS 4202, designed by Cytec, now offers the possibility of tailoring the iron co-extraction, so that appropriate Cu:Fe selectivity can be achieved in the solvent-extraction operation to maintain an electrolyte Fe:Mn mass ratio of >10:1, while retaining the other benefits offered by ester-modified aldoximes. The results of an integrated solvent extraction-electrowinning pilot-plant trial are presented, in which the performances of the conventional extractants ACORGA® M.5774 and LIX® 984N are compared with LS 4202. The Cu:Fe selectivity is demonstrated, along with results on the transfer of other impurities to the advance electrolyte.

Jan 1, 2007

By D MacKenzie

The Rise & Shine Shear Zone is a shallow-dipping Cretaceous late metamorphic shear zone formed in a compressional environment. The Shotover mineralised system is dominated by normal faults with well-defined vein systems that cut across Miocene schist folds and faults related to the inception of the Alpine Fault. Despite the geological differences between these mineralisation systems, they share many common features of hydrothermal alteration that have resulted in disseminated gold in altered sheared schist. The most distinctive feature of both systems is the abundant ankeritic carbonate that has formed from decomposition of metamorphic chlorite. Excess iron from this alteration reaction combined with hydrothermal sulphur to form sulphides that host the disseminated gold. The chlorite decomposition reaction was reversed in the latter stages of both mineralisation systems, and this was accompanied by further gold emplacement in the Rise & Shine system.   Both alteration systems involved initial decomposition of metamorphic albite, followed by deposition of albite as a vein mineral in the latter stages. The fluid flow that yielded the disseminated gold was controlled by microshears that pervade host schists, in strong contrast to many Otago Schist vein systems where host rock alteration is absent. The ankeritic alteration in the Shotover and Rise & Shine mineralised systems has increased the volume of mineralised rock, and may have made suitable targets for large-tonnage, low grade gold deposits.

Jan 1, 2007

By J. A. L. Napier

The evaluation of stress distributions and deformations in the vicinity of tabular mine layouts has been carried out routinely for many years using the displacement discontinuity boundary element method (DDM). In this approach, mine layouts are approximated as irregular shaped planar cracks (or slits) where the ?width? of the crack, corresponding to the excavation height, is assumed to be negligible compared to the in-plane, lateral dimensions. Early implementations of this approach have employed square element tessellations with constant displacement discontinuity component values. This is generally restrictive when considering the analysis of irregular pillar layouts or the intersection of fault planes with excavations. This paper describes a general revision of this approach in which triangular or quadrilateral element shapes are introduced in conjunction with higher order variations of the displacement discontinuity shape functions. This facilitates an accurate evaluation of detailed stress and displacement components close to excavation surfaces and allows the investigation of local damage and failure behaviour associated with particular geological structures such as weak parting bands or weak layers. A method to embed these features in an efficient and accurate multi-level solution scheme is described. This formulation can be extended to allow the analysis of shallow-depth pillar layout problems, facilitating the assessment of the interactive response and stability of shallow depth pillar layouts. A simple deformation model is introduced to facilitate the assessment of pillar failure and bursting potential in shallow mine layouts. The computational techniques described here have been implemented in a computer code called TEXAN (Tabular EXcavation ANalyser) and are illustrated by the simulation of a particular multiple reef pillar mining problem in a shallow depth platinum mine.

Jan 1, 2007