Search Documents

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By G D. Cooper

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

By A. M. Esteves

This paper addresses the question ?What constitutes the right level of investment in community goodwill?? Mining companies are still grappling with this subject even though the business case for community investment has been accepted at a general level, as a strategy for competitive differentiation, risk mitigation and a desire to deliver - and to be seen to deliver - a ?net benefit? to affected communities. Gaining senior management commitment to long term social projects, by definition characterized by uncertainty and complexity, is made easier if projects are shown to benefit the site?s strategic goals. Case study research amongst mining companies, including interviews with social investment decision-makers, has assisted in developing a SI-DAT (Social Investment Decision Analysis Tool), a decision model for evaluating social projects in order to create value for both the company and community. Multi-criteria decision analysis techniques integrating business planning processes with social impact assessment have proved useful in assisting mining companies think beyond seeking access to required lands and peaceful relations, to how they can meet their business goals and contribute to regional development.

Jan 1, 2007

By Taehong Kim, Carl Pannuti, Nikolas Sokol, Walter Herrick

BACKGROUND This paper discusses work performed as part the rehabilitation of the gravity flow section of the New Croton Aqueduct (NCA) during an approximately two year period between 2004 and 2006. The goal of the project was to restore the gravity flow section of the NCA to optimal operating condition, extending the lifespan of this significant water supply for the New York City metropolitan area. Rehabilitation of the NCA was purposely scheduled before the completion of the new NCA Water Treatment Plant now under construction (Figure 1). The NCA is a 3.73 to 4.34 m (12.25 to 14.25 ft) diameter brick-lined circular andhorseshoe shaped water tunnel constructed between 1885 and 1891. The NCA conveys water for approximately 50 km (31 miles) by gravity and pressurized flow from the New Croton Reservoir in Westchester County, NY to distribution and reservoir points along its alignment, terminating at a distribution station at 135th Street and Convent Avenue in Manhattan, NY. Prominent features of the NCA include a large intake facility at New Croton Reservoir, 38.6 km (24 miles) of gravity flow horseshoe shaped aqueduct, 11.3 km (7 miles) of pressurized flow circular aqueduct, 2 siphons, and 36 open shafts and headhouse chambers which are used as sampling, access and blow-off locations. Until a partial inspection in 1982, the NCA had flowed continuously since its completion nearly 100 years prior. Flow tests have confirmed that the NCA can convey up to 12.7 m3/s (290 mgd) (Figure 2). Cover depths of NCA vary considerably, ranging from a few to hundreds of meters, typically of hard rock. Primarily mined using means conventional for the late1800s, construction of the NCA also employed cut and cover methods in several low-lying sections of the alignment, totaling approximately 1.6 km (1 mile). The NCA crosses through numerous lithologic changes, fault/shear zones and under several significant water bodies including the Pocantico, Saw Mill and Harlem Rivers and the Tarrytown Reservoir. The NCA passes under the Harlem River as a siphon at a depth of approximately 122 m (400 ft) below grade (Figure 3). Soon after construction the Aqueduct Commission Reports on the New Croton Aqueduct documented prominent defects such as large voids behind the lining. More recently, large-scale inspections of the gravity flow section performed during the 1990sand a 2004 inspection of portions of the pressurized sections of the NCA have revealed additional defects such as open and/or deteriorated masonry joints/cracks, leaks ranging from trickles to several liters per minute into and out of the NCA, missing bricks, formed openings, and in one place, a rupture through the liner with discernable

Jan 1, 2007

By Anthony K. Anyimadu, Chris M. Rule

Froth flotation is the primary mineral processing separation step employed in the beneficiation of PGM ore bodies. Anglo Platinum operates a significant portion of the total installed flotation capacity in the PGM industry, which is installed at 20 operating plants across the Bushveld. PGM flotation has undergone a considerable evolution in both the capacity of flotation cells employed as well as in the circuit design configuration over the past thirty years. Certain of Anglo Platinum?s flotation circuits have been in operation for a relatively long period of time, (in some operations installed equipment dates from the 1960?s) and this allows comparative operating performance between various equipment types and circuits to be evaluated. This paper summarizes some aspects of this experience. Research trends in flotation are continuously monitored to incorporate appropriate findings into existing and future circuit designs. Continuous evaluation and monitoring of flotation performance is undertaken to identify opportunities for increasing flotation efficiencies. Mineralogical and fractional analyses of plant composites and survey samples are analysed to interrogate speciation and association data. This analysis has enabled a better understanding of priorities and opportunities for improved metallurgical performance. These opportunities are divided into three improvement areas: stability, liberation, and fines flotation. The paper discusses these, as well as the circuit design improvements required to take full advantage of the opportunities identified.

Jan 1, 2007

By D. Royston

Gold ores containing antimony suffer from poor recoveries of gold in cyanidation due to the impact of antimony on the cyanidation process. Techniques such as lowering the pH for cyanidation can improve gold recovery, nevertheless a limit can be reached where high cyanide consumption makes traditional processing uneconomic. The paper outlines a process for the pre-treatment of gold-antimony concentrates to remove the antimony resulting in a low-antimony content gold-bearing residue suitable for efficient treatment for gold recovery through cyanidation. This hydrometallurgical process produces a by-product credit of commercial grade antimony trioxide as Senarmontite that can significantly offset the cost of the pre-treatment.

Jan 1, 2007

By James Ludwiczak

This paper consists of the conduct of a forensic criminal investigation of the components, construction, use, and functioning of two suicide bombs. As the title states, the task was to form professional opinions as to whether the bombs would work, would cause property damage, and would injure or kill. The bombs were created and installed by a defendant in a Federal death penalty case where the defendant’s daughter was killed in a shootout with the West Virginia State Police. The two black powder bombs were placed under the front seats of the defendant’s automobile and were designed to function by the use of a toggle switch connected to the automobile’s cigarette lighter. The forensic work first consisted of an inspection of the remains of the wiring system and bombs at the Bureau of Alcohol, Tobacco, and Firearms Laboratory, in Ammendale, MD. This was necessary to determine and detail the wire diameter and lengths, the lengths and size of the wire used, the type of toggle switch used, the type of containers, the type of rocket motors used to initiate the black powder, the manufacturer and amount of black powder used in each bomb, and the type, wraps, and amount of duct tape used for the construction of each bomb. Using this data, tests were conducted by duplicating the wiring system and the two bombs to insure that the system functioned properly. Each bomb was duplicated and initiated to observe the violence produced when initiated in the open air. Duplicate bombs were placed under the seats of a similar type of automobile and initiated. The purposes of the tests were to duplicate the bombs, to observe the violence of the initiation, and to observe the damages to the automobile produced by the initiation.

Jan 1, 2007

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By R. J. Davidson

Arguments are presented in favour of a new interpretation of the chemistry pertaining to the dissolution of gold, when this takes place in typical gold plant leach circuits where calcium is present in solution. It is suggested that under these conditions the standard chemistry, as it applies in the absence of calcium, is no longer valid. Thus the concept of very soluble sodium and aurocyanide ionic species in solution is replaced by the presence of weakly soluble calcium aurocyanide, which is a covalent coordination complex that is non-ionic. Supporting evidence for this is provided and the implications that the presence of calcium in gold plant circuits may have for operational efficiency are discussed. In particular, because of the formation of this weakly soluble calcium complex, the addition of lime to the leach circuit is questioned. Arguments for the use of a sodium hydroxide/sodium carbonate/sodium bicarbonate buffer solution as a means of controlling pH and of increasing ionic strength in a so-called ?soft? leach are presented. Such a lime-free system, besides benefiting the leaching of gold, would have many downstream benefits in existing CIP circuits. Furthermore, the direct electrowinning of gold from the leach now becomes potentially feasible.

Jan 1, 2007

Introduction The science of geometallurgy requires that ore characterization be performed holistically, that is, with consideration of ore quality on plant performance and product quality. Geometallurgy, by definition, requires knowledge of geology, mineralogy, extractive metallurgy and pyrometallurgy. Examples of the ore characterization challenges for the geometallurgist in the production of iron ore pellets from low-grade Proterozoic iron formation are presented here. Ore Characterization Ore characterization, the quantifying of mineralogy, grain size and the texture of ores, is an often overlooked tool in improving process efficiency. Some mineral related problems are not unique to the production of iron ore pellets; e.g. the problems caused by expanding clays in flotation. The negative impact of carbonate minerals in the ore on pellet productivity and pellet quality are unique. The long and complex geologic history of Precambrian iron formations contribute to modifications of grain size and the introduction of complex textures.

Jan 1, 2007

By D. Bessinger, N. Rughubir

Exxaro Sands KZN produces?among other heavy mineral products?high titania slag, which is used as feedstock to the pigment industry. The titania slag is produced from the smelting of ilmenite in two 36 MW DC furnaces. In this smelting process carbon monoxide gas is produced. This gas is cooled, scrubbed and washed to remove entrained dust. This paper provides details on the gas cleaning plant system and the chemistry, mineralogy and size distribution of the particulate material contained in the off-gas stream. Characterization of the dust shows that is consists mainly of ilmenite, but with relatively high levels of SiO2and MnO. Smelting of the dust in a 500 kW DC furnace was carried out to investigate the potential for recovering valuable elements from the dust.

Jan 1, 2007

By M. Kirsten, W. H. Botha, M. H. Fox, J. A. Moolman, A. J. Lathwood

Water is a valuable and in many areas a scarce resource. Governmental legislation regulates the environmental impact of water usage and wastewater disposal through the issue of licenses. These requirements mean that hydrometallurgical refineries must ensure that water consumption and water disposal is managed on a continuous basis in order to prevent the repeal of their operating license. Water balances are often overlooked during the design of a hydrometallurgical refinery. Recent changes in environmental legislation have forced both design engineers and operational management to review water use and disposal within these processes. Unlike concentrators where water can easily be recovered by recycling from tailing dams, water introduced into hydrometallurgical refineries becomes contaminated with soluble metals and thus requires pre-treatment prior to disposal. This paper discusses the various concerns that need to be considered during design and operation of hydrometallurgical refineries with respect to the water balance.

Jan 1, 2007

The VoD of non-ideal explosives depends on the charge diameter and the thickness, strength and sound velocity of the confiner. VoD measurements are made to evaluate explosives for development, quality control and prediction of field performance. In testing, the container is part of the explosive system and affects the measured VoD. Pipe testing in cardboard tubes delivers the best guide to unconfined critical diameter and minimum VoD range, but the thickness of the pipes affects the result close to critical diameter, even in emulsions. PVC pipes are not good for unconfined test work because they provide relatively strong confinement. Care must be taken to select pipes with constant relative pipe area across the range of diameters. Where pipes are used to evaluate the effect of confinement, the ratio of the wall thickness relative to the thickness of the detonation driving zone in the explosive needs to exceed 0.5 to create full confinement and the ratio of the detonation velocity to the confiner wave speed must be considered. Estimates for critical thicknesses are provided from Non-Ideal detonation models. The relationship between confinement modulus and VoD is discussed and indexes are suggested for quantifying the explosive performance.

Jan 1, 2007

By M. Gruber-Pretzler

Technical Sn- bronzes tend to form both macrosegregations and microsegrega¬tions during DC-casting due to the particular thermodynamic properties and kinetics of phase transformation. As a result a heterogeneous cast microstructure forms that is some¬times a reason for a decrease in workability. The extent of macrosegregations in DC-casting can effectively be influenced by casting parameters like casting velocity, primary cooling or inlet geometry which in fact change the relative flow between the melt and the forming solid. In order to understand the influence and interaction of the related phenom¬ena, simulation methods are applied. The solidification of the strand as well as the forma¬tion of macrosegregation are simulated with a two phase volume averaging model. The velocity field of the melt flow is explicitly calculated by solving the corresponding mo¬mentum conservation equations. Within the mushy zone the local formation of microseg¬regations in the presence of feeding flow is estimated. The thermodynamics of the Cu-Sn system is accounted for and it is distinguished explicitly between interface and average concentrations. To investigate the influence of feeding flow on the formation of mac-rosegregations, a study has been performed. Based on this result, the phenomena of mac¬rosegregations are described in a detailed discussion.

Jan 1, 2007

By J. Engel

The talc deposit in Gemerská Poloma lies 350 to 400 m under the surface; the whole deposit is located at the highest-level drinking-water-source protection zone, therefore, opening in this mining area (a well, a ramp) requires higher investment, operational and water protection costs. The adit, outside the mining area, with a length of 4200 m, rising with a gradient of 3? and a diameter of 10.3 m2, allows free passage/runoff of mining-water through the adit, and guarantees low costs for transporting produced material and equipment. This solution is in total less demanding from both investment and operational point of view.

Jan 1, 2007

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007

By Issa S. Oweis

Two Towers are currently under construction in Central Moscow in the Russian Federation. Building A is a 96 story tower and Building B is a 65 story tower. The columns in both structures bear on a thick concrete mat that is supported on drilled shafts, 1.5 m in diameter. The shafts derive their capacity from weak limestone with layers of marl. Assigned allowable shaft loads were initially based on rock strengths that were later verified by load tests using the Osterberg Cell. One of the load tests was carried to near failure which allowed refining socket friction values that were later used in the design of Building A. All shafts were advanced using an auger and concrete placed in the dry. Grout tubes were placed with the reinforcing cage which allowed grouting of the limestone in contact with the shaft. Load sharing between the shafts and the mat was approximated using published methods as well as site specific finite element analysis. This paper covers the methodology of design, analysis of the Osterberg results to derive non-linear stiffness of the rock and differences between finite element analyses and results by approximate methods.

Jan 1, 2007

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007