Search Documents

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

The copper electrodeposition from sulphuric acid electrolytes in the presence of Thiourea and Gelatin as additives was investigated by electrochemical noise and cyclic voltammetry in conjunction with the scanning electron microscopy technique. This study was oriented to examine the utility of using electrochemical noise "EN" technique to characterize the electrowinning process and the deposit structure morphology as compared to cyclic cyclovoltammetry "CV", an electrochemical method generally used industrially. Both EN and CV techniques were successful to reveal the effect of different concentrations of Thiourea and Gelatin on copper electrodeposition process. In this study, CV has detected an excess of Thiourea leading to porous deposit. While, the electrochemical noise analysis in the time domain (skewness and kurtosis parameters) as detected the presence of nodules and has given useful information concerning the morphology of the deposit closely related to the macroscopic and microscopic studies.

Jan 1, 2007

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By Lon Santis, David Leidel, John Tatom, Meredith Hardwick

This paper describes the development and methodology of the Institute of Makers of Explosives’ Safety Analysis for Risk (IMESAFR), a risk analysis software program for commercial explosives operations. IME is a nonprofit safety and security association devoted to the safe and secure manufacture, transportation, storage, and use or disposal of commercial explosives in the US and Canada since 1913. The software methodology’s basis is the U.S. Department of Defense Risk Based Explosives Safety Criteria Team’s Safety Assessment for Explosives Risk (SAFER) software. A diverse group of industry and government experts contributed to modifications to SAFER that reflect commercial operations. IMESAFR is intended to supplement the American Table of Distances (ATD) and offer standardized methods of managing risk from a wide variety of commercial explosives operations where the ATD does not apply. The modifications made to SAFER primarily involved the addition of commercial activities and potential explosives sites (PES). A review of commercial explosives accidents and operations over the last 20 years served as the basis for establishing probability of event values. An industry survey of commercial PES types in the U.S. and Canada was conducted to identify and address critical differences in commercial structures as compared to the military structures in SAFER. The paper concludes with discussion of the potential uses for quantitative risk analysis (QRA) and a description of other explosion effects software

Jan 1, 2007

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

By R. Tinsley

Project-finance risk assessment is mature and approached systematically. Mining industry due diligence remains fragmented with specialists addressing different aspects of the project such as reserves/JORC, environmental impact, commodity market, even financial analysis/ modelling. Each professional has a natural tendency to believe that the risk factors they have examined are the key ones necessary to be reviewed, as if their review will stand in isolation from others in the way a project materialises. By first laying out the project risk categories and risk matrices, this paper examines the due diligence process with a keen eye to the risk assessment and overlap/interaction. Some cross fertilisation of due diligence techniques from other industry sectors is placed into the mining context. Six case studies are then presented with regards to due diligence features in each project's feasibility review or financial information/ offering memorandum. A power case first shows the differences between the due diligence expectations of banks versus bond financings. Then some Australian and Indonesian mining development cases are analysed to see the due diligence learning points. Some of these were project/due diligence failures. The conclusion focuses on the value of a systematic risk assessment for project evaluation, all from the project-finance perspective.

Jan 1, 2007

By R. Boom, L. Holappa

In the present paper, microstructure changes of solid-state reduction of industrial chromite pellets and lumpy ore were investigated with SEM/EPMA. To simulate the reactions in the packed bed zone of the Submerged Arc Furnace (SAF), carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at 1500 °C. Scanning electron microscopy was used to observe and analyse the structure and composition changes of the chromite samples. It was found that reduction of lumpy ore generally took place slower than that of pellet. In all samples, chromite reduction proceeded faster in the outer part of the sample than in the centre part. The reaction mechanism is discussed on the basis of experimental results and earlier investigations. The possibilities to optimize the FeCr production process are also discussed.

Jan 1, 2007

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By M. Wu, X. Zhao

This paper presents an integrated pipeline transport system for thickened coal sludge, which combines pretreatment and pipeline transport with combustion techniques of thickened coal sludge. The pipeline can transport thickened coal sludge with a sufficiently high solids content (about72%?77%) and high apparent viscosity (about 1 000Pa?S?3,000 Pa?S) directly by pipeline having neither use for water nor an addition agent. The transport distance can be as high as 1 000 metres. In particular, the operating principles, key equipment and technical parameters of this integrated system are examined in this paper. The integrated system effectively causes no pollution to the environment because it is completely sealed, and conserves energy over traditional conveyer designs. Keywords: pipeline transport; integrated system; circulating fluidized bed boiler; thickened coal sludge; high solids content

Jan 1, 2007

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By K. H. Al-Rawahy

Appreciation and awareness of the unique nature of mineral investment and ultimate development of a mine are crucial in promoting sustainable development. Special characteristics of mineral development include high capital intensive, long pre-production period, high risk, and the unavoidable ?economic? depletion. This paper examines ways to integrate these unique attributes of the mineral industry into the educational process, so that a properly advised and knowledgeable culture in terms of a sustainable mineral industry can be developed. Specific approaches are investigated in order to achieve this objective. These include a stochastic evaluation of a mineral investment proposal, adding a premium to the cost of capital that is used for valuation process, and internalizing incidental costs to the private cost function, thereby realizing the true (vs. apparent) marginal social cost of the proposed development. Undoubtedly, a total evaluation of any mineral project that accounts for both tangible and intangible parameters will contribute to sustainable development objectives. By incorporating the practical application of apparent theoretical topics such as risk, probability, and externality, and their relevance and impact on mineral lifecycle (prospecting, exploration, development, exploitation, use, and ultimate disposal) into the educational process, it is hoped that a generation of technocrats and decision makers that are familiar with and concerned about sustainable development will emerge.

Jan 1, 2007

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007

By T. Beamish, I. Vasilev, T. Nikolov, E. Marinov, D. Kirilov, P. Barrios

In April 2005, Umicore Copper de-merged from Umicore Group and created a new independent Copper company called Cumerio. As a separate company, Cumerio is a major European copper smelter and refinery and a leading producer of copper products such as wire rod, billets, cakes and specialty rod with a total production capacity of copper products in excess of 500,000 tpy with production plants in Belgium, Italy and Bulgaria. The Pirdop Smelter is the only state-of the-art smelter in South East Europe and it makes Pirdop the natural hub for the copper industry in the region. In order to be competitive in the international market the main challenges facing Cumerio are to maintain its low cost structure and to achieve higher production volumes while reducing its impact to the environment and striving for continuous improvement of the production process. Cumerio's state-of-the-art smelting facility in Pirdop has recently increased the anode production capacity to 250,000 tpy by the installation of the third evaporative cooler on the converters section that allows operating with three-hot converters. In April 2007 a general shut-down for repair and modification on the Flash Smelting Furnace and Waste Heat Boiler is envisaged. At this time a revamp of one of the existing Sulphuric Acid Plants is planned, resulting in a further copper capacity increase to 275,000 tpy with modest Capex. In 2005 Cumerio received from the Bulgarian Ministry of Environment and Water the Complex Permit under the EU IPPC criteria. Accordingly an Environmental Compliance Program was defined targeting a large reduction in the secondary emissions. The system will be commissioned in May 2007. In order to better integrate the smelter and refinery in Pirdop and to respond to the growing demand for cathodes in the region, a new state-of-the-art Electrolytic Refinery with an installed capacity of 180,000 tpy will replace the existing refinery. The new refinery is expected to be fully operational as from early 2008. This paper describes the challenges and the projects.

Jan 1, 2007

By S. Watkins, D. Apel, B. Gray, R. Moss

Currently, there are several techniques and technologies available which are used by mining industry in its attempts to remotely monitor the ground movements both at surface and underground mines. The currently available remote distance meters and distance change monitors mainly use phase change and time-of-flight techniques. The described monitor uses triangulation technique to track position of an optical spot projection and then image processing to measure mine wall movements. The system can be easily automated and poses no obstruction to mine traffic. The position of an off-normal laser spot will shift as the target wall moves. The described ground movement monitoring system has potential for superior accuracy and target monitoring can be made through air (gaseous) or other transparent media. The theoretical accuracy and range of this system depends solely on the resolution and focal length of the camera being used. The remote capabilities of the system make it uniquely suited to applications where monitoring is required in high-traffic, inaccessible, or unstable and dangerous areas of a mine.

Jan 1, 2007

By P. Goosen

The paper presents a basic summary of the approach to hydraulic scale-model tests as may typically be applicable to slurry flow situations. A case study is presented illustrating how hydraulic scale-model tests can be of significant benefit in evaluating the performance of novel or unproven slurry handling equipment. In this case the equipment tested was a fan-shaped expansion piece used to spread the discharge from a launder over the full width of a dewatering screen. The tests showed that the device did indeed distribute the slurry flow both in terms of volume and solids mass, but not perfectly uniformly. Unfortunately the equipment was not taken beyond the model test phase. The scale-model test approach did, however, prove to be very useful as it is considered to have provided a good indication of the expected performance of the full-size unit. Significantly, this was achieved at very low cost compared to the cost of installing the device into the proposed plant and having to later change it out for an alternative or live with the less than optimal performance. The paper illustrates the value that can derive from applying hydraulic scale-model testing techniques to evaluating the performance of new or unusual slurry handling equipment. There is particular value in situations that do not lend themselves to numerical modelling.

Jan 1, 2007

By Bernard H. Hertlein

The introduction of LRFD methods for structural design has been a gradual process by AASHTO, ACI, AISC, ASCE, and the FHWA, which has largely been ignored by the deep foundations industry. In 2007, however, the industry has been obliged to embrace LRFD for any deep foundations on projects involving federal funds. The authors are concerned that the risks caused by the need for, and the difficulty of providing, reliable quality assurance, will result in unnecessarily high safety factors that will defeat part of the purpose of LRFD. A primary attraction of LRFD for owners and engineers alike is that it promises more efficient design, and therefore cost reductions. Unfortunately, a key element of LRFD philosophy is often overlooked - that the applied safety factors can be rationally reduced, often allowing less material to be used, thus saving costs, but only if all the risk factors involved are identified and closely controlled. This means that both the quality of the materials and the quality of the construction work must be adequately monitored, and held to an acceptable standard. In the case of deep foundations, the soil in which the foundation is constructed is also a critical component that must be taken into account in the assessment of risk factors.

Jan 1, 2007

By V. G. Pienaar, B. M. Mbiya, P. T. Slatter

[a constant b constant cc onstant c' constant D pipe diameter (m) Dshear shear diameter (m) E error function fth theoretical friction factor F function F' function K fluid consistency index (Pa sn) kv valve loss coefficient L pipe length (m) n flow behaviour index N number of data points ?P valve pressure drop (Pa) Q flow rate (m3/s) Re Reynolds number Re3 Reynolds number (Slatter) V average velocity (m/s) Vann annulus velocity (m/s) x variable X number of independent variables y variable Y number of fundamental dimensions z variable µeff effective viscosity (Pa s) ? valve degree of opening d partial derivative ? fluid density (kg/m3) [ ] function]

Jan 1, 2007