Search Documents

By Paul A. Lang

Jan 1, 2007

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By G. S. Ospanova

The results of complex processing sulphide copper ore and advantages of recovery of copper by vat and heap leaching, sorption, cementation and electrolytic solutions processing and utilization of waste material after heap leaching of copper for production of building materials were investigated. The combined chemical solvents with the additives of oxidizing agents are developed at the KazNTU. The solvents are inorganic or organic chemical reagents, which form complexes of Cu, Au, Ag, Pt, Ni, Sr, Co etc. Recovery of non-ferrous metals from solutions and purification of industrial waste waters is carried out on the base of using new synthetic and natural sorbents (from local raw materials) which are able to bind ions in both cationic and anionic forms depending on type of ligands and external conditions. Optimum parameters of copper sorption were determined. The developed wasteless technologies of copper extraction from sulphide ores with usage of new non-toxic solvents and accessible sorbents with full recycling of water are tested in pilot scale heap leaching, and are recommended as the ecological, economical and practical alternative to traditional methods.

Jan 1, 2007

By Robert Hopler

In part four, the instrumentation used to detect the vibrations from the 1876 Hell Gate (East River, New York) reef-clearing blast was discussed. The apparatus consisted of cups of mercury and microscopes or other magnifying instruments to detect ripples or waves on the surface of the liquid metal.

Jan 1, 2007

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By A. Robles-Vega

Personnel of Mexicana de Cobre, a subsidiary of Southern Copper located in Nacozari, Sonora Mexico have been working in the past few years on the development of a process to treat and manage, in an environmentally accepted practice, the residues and effluents generated during the process. To date, this team has been reviewing existing technologies and also has explored new alternatives. At the end of this phase, a novel, efficient and complete process has been configured which will be able to treat some solid and liquid streams such as Teniente converter dust, Peirce Smith converter dust, a Sb-rich precious metals slag, copper refinery electrolyte bleed, acid plant blowdown and an acid bleed of the precious metals plant. The process will consist of a leaching stage, followed by a very selective copper precipitation using novel technology which has been named as back reactions. After copper precipitation, impurities (As, Sb and Bi) will be precipitated mainly as arsenic trisulfide (As2S3) using H2S(g) which will be generated by means of a new process developed in our company. At the end of the process, small volumes of arsenic trisulfide will be vitrified and then disposed as a stable residue.

Jan 1, 2007

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By P. E. Walker, M. E. Reed, R. C. Sims, B. Snowdon, D. E. Fallas

An advanced Flash Furnace feed system is the key to improving furnace performance. Clyde-WorleyParsons has developed a revolutionary pulseless pneumatic injection feed system technology, capable of delivering a range of benefits to operators of Flash Furnaces. The solution was created by combining the pneumatic conveying and injection knowledge, expertise and technology of Clyde Materials Handling with WorleyParsons&apos; flash furnace process and operating experience. Optimal furnace burner performance requires the feed material to be presented to the burner as a stable, pulseless and accurately controlled flow, distributed evenly around the burner tip circumference. These simple requirements appear obvious, but are extremely difficult to satisfy in industrial environments and are not achieved by conventional feed systems. Our analysis of existing operating furnaces has identified the link between pulses in concentrate feed rate caused by conventional drag chain conveyors and rapid fluctuations measured in the furnace pressure. These fluctuations occur at a timescale close to the reaction shaft residence time and lead to unwanted instability in the primary furnace reaction zone - the flame. Through the use of the solution created by Clyde-WorleyParsons, it is predicted that the much more accurate control of feed rates achieved can lead to substantial improvements in furnace output, increased oxygen efficiency and better control of the composition of furnace liquids, such as matte, blister or slag. All these improvements lead to significant increases in smelter output and efficiency, and deliver high economic value compared to the cost of the feed system. Clyde-WorleyParsons&apos; solutions can be deployed on greenfield sites or retrofitted, and therefore, have the capability to improve feed control at both new and existing smelters. This paper will discuss the field test work undertaken to date, the impact of findings and the ongoing analysis of linkages between instabilities in the various components of conventional feed systems and furnace pressure stability.

Jan 1, 2007

Existing production facilities are constantly looking at ways to increase capacity. Many recent solutions have focused on the implementation of capital and infrastructure projects. It is accepted that capital expansions are frequently necessary for production gains; however, in many cases existing assets have the potential to deliver substantially better throughput than they are currently achieving. By focusing on automation of production control systems, production reporting and business processes substantial gains can be achieved utilising existing assets. This potential can be realised quickly and has been proven across several sites and industries. In the Pilbara region of Western Australia throughput gains of between two per cent and 25 per cent (translating to millions of tonnes per annum) have been achieved from existing assets using the methodologies discussed. The improvement process involves evaluating the entire production chain from the time the ore arrives at the plant to the time it is dispatched. A technical evaluation of the performance of the control system and plant automation interfaces to upstream and downstream processes is conducted. The relationship of these processes to the business systems and the human interface to the systems is reviewed to ensure a complete picture of the system is understood. Technical evaluation targets include: individual equipment operation, the engineering level of control systems, feed controls, etc; managing recirculating loads, surge capacities, dynamic inventories as well as management of in-feed systems and integration into yard and out-feed systems; and communication flow between control and other systems, data alignment between rail and shipping schedules, yard systems, sales systems and maintenance systems including such fundamentals as truck dispatch links to plant control. In parallel with the technical evaluation, business system evaluation takes place, including analysis of the operational systems, methods and personnel.

Jan 1, 2007

By M. H. Ali

Codelco, a multi-process primary copper producer, is undertaking a full life cycle inventory (LCI) of all its commercial products based on copper and molybdenum. During this work, many questions have surfaced regarding the contribution of process unit design to specific aspects of a product&apos;s LCI and, more importantly, how such designs could be improved using a life cycle perspective. Management strategy efforts were undertaken to improve the LCI footprint, however it was found that the corrective actions were almost impossible to apply at the operation level in plant, given the ongoing timing pressures of extractive mining, and costs saving priorities. Additionally, it was found that most of the important comparative differences between operations had structural reasons. In this circumstance, the LCI practitioner group from 1M2, and the environmental managers from Codelco, decided to shift its efforts to place the critical LC1 aspects to the design process of future developments. Hatch Associates has developed unique tools in their Sustainable Plant Design (SPD) package that compliment and enhance LCA methods; these effectively drive sustainability into the heart of the design process. By using LCA and SPD in a project design phase, you cannot only address potential hotspots, but also decide on materials, location and size of certain facilities to optimize for energy efficiency. Moreover, you can avoid the shifting of environmental burdens upstream or downstream within the plant and finally it is extremely useful in identifying opportunities for greenhouse gas reduction.

Jan 1, 2007

Palabora Mining Company is operating a copper block cave mine in the Limpopo Province of South Africa. The mine was developed in the late nineties with a target ore reserve of 220 million tonnes of carbonatite at 0.69% copper. At 30,000 tonnes per day the operation had an estimated life of mine of approximately 23 years. Cave induced open pit side wall failure occurred in late 2004 with 130 million tonnes of waste reporting to the bottom of the open pit. This failure resulted in potential sterilization and dilution of the ore reserve and subsequent reduction in life of mine. Physical and numerical modelling indicated potential losses of up to 30% of the original ore reserves. Cave Management tools based on throughput principles are utilized to manage the failed waste ingress and ensure an optimum life of mine. Extracting the maximum rate possible, as soon as draw points are commissioned, with the view of achieving the highest production in the short term, is any mining operation?s goal as more money is required sooner. This approach, of course, improves the cash flow but presents a risk in the cave propagation profile as overall draw control is compromised. At Palabora it is evident from a Mineral Resource Throughput Management (MRTM) point of view that maximum production in the short term is not the solution. If high production rates are achieved and the profile of the cave is not manage correctly, this results in failed waste reporting to draw points earlier with adverse effects on grade. This would effectively and significantly shorten Palabora?s Life of Mine. The applications of good MRTM principles are required to assist the value chain for sustained profitability. The process commenced with change management paving the way for a better understanding and a holistic view for all role players.

Jan 1, 2007

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By B. Huffman

This paper examines several new trends in the design and application of linings for copper melting shaft furnaces including the use of large shapes, monolithic back-up linings and improved refractory engineering to significantly reduce refractory installation time, diamond saw blade costs, fuel and down-time. The net results are shown to be dramatically increased refractory service life, reusable safety linings, elimination of hot spots and lower refractory disposal costs.

Jan 1, 2007

By J Moncrieff, P Bellairs

The Black Star Open Cut is located immediately adjacent to the township of Mt Isa and is situated in the middle of extensive pre-existing infrastructure including two concentrators, two smelters, a wet fill plant and two shafts. At any one time there are in excess of 500 people working on the surface within an industry-accepted 600 m exclusion zone from Black Star blasts. Apart from the surface operations there are also the underground operations including the lead mine (closed in December 2005) and the Enterprise and X-41 mines that must clear for all Black Star blasts. The application of industry standard blasting exclusion zones (600 m) was risk assessed as imposing operationally prohibitive constraints which could cause significant business interruption due to the logistical challenges required to ensure that all personnel from surface plants were evacuated for each blast and potential for lost production whilst these personnel were not operating the plant. In was therefore an imperative for the blast exclusion zone to be reduced. This was achieved by the: use of a QA/QC team to ensure that relevant drill and blast implementation is within an acceptable tolerance (KPIs) from design; use of high-quality stemming material called HMR, which is a by- product of the concentrating process and is generally sized at -14 mm with very little fines; implementation of appropriate training and support to Black StarÆs own blast crews, reinforcing the need to achieve the designed amount of stemming in every hole; and provision of appropriate support from Black StarÆs management for additional resources to ensure that every blast achieves design within the KPIs but especially in high-risk areas. The blast exclusion zone was successfully reduced after monitoring the flyrock results from more than 176 blasts. Black Star Open Cut now maintains a minimum blast exclusion of 200 m in critical areas; however, general blasting currently uses a 250 m exclusion as this provides additional risk management whilst still minimising the logistics associated with clearing and securing the slightly increased area.

Jan 1, 2007

By I. B. Schalamuk, R. E. de Barrio, M. J. Pons, M. B. Franchini, L. Meinert

"Several Fe, Fe-Cu, and Cu-Ag prospects hosted by Mesozoic carbonate-rich sedimentary rocks that were intruded by diorite stocks define an approximately 20 × 200 km belt along the Andes Cordillera of southwest Mendoza province, Argentina (34°-36°S). This belt includes the Hierro Indio and Vegas Peladas Fe skarns, Las Choicas, and several other Cu-(Ag) prospects.The main features of the Fe skarns include: association with mantle-derived middle Miocene (~15-11 Ma) diorite stocks and sills; widespread alteration including epidote ± amphibole ± magnetite endoskarns, and zoned garnet (Grs0-66 Adr32.5-100) ± magnetite ± pyroxene (Di24-50 Jo2-9 Hd74-41) exoskarns formed from oxidized, saline, high-temperature brines (530º-660ºC; 60-70 wt.% NaCl equiv.); and magnetite-hematite orebodies associated with quartz ± epidote ± calcite ± actinolite formed at lower temperatures (290º-436ºC) from saline fluids (32-50 wt.% NaCl equiv.) of magmatic origin.West of the Fe skarn belt, the Valle Hermoso district covers more than 300 km2 and hosts several poorly known Cu-(Ag) prospects (estimated 30 Mt with 1.5% Cu and 20 g/t Ag). These prospects share many characteristics with the iron oxide copper-gold-type systems and manto-type Cu deposits of northern and central Chile. One of the prospects (Las Choicas) is located at the apex of a regional 015°-trending anticline, along the contact of stratified calcareous sandstone and limestone (Neocallovian-Oxfordian) with a diorite pluton. This pluton has positive Ta and Nb anomalies (on normalized diagrams) and a high Ti content, features uncommon in Miocene diorites associated with Fe skarns and of magmas derived from sub-arc mantle sources. Alteration at Las Choicas includes early widespread chlorite + calcite ± albite ± scapolite ± ilmenite or titanite ± apatite, and local actinolite ± hematite ± biotite alteration of diorite and sedimentary rocks along contacts. Later Cu mineralization (1%-10% Cu) is associated with calcite ± albite ± quartz alteration in fractures, vein networks, and crackle breccias. Mineralization is zoned from bornite ± chalcopyrite ± millerite with Zn, As, Mo, Ag, and U anomalies in the main orebody, through chalcopyrite-rich breccias with Zn anomalies, and chalcopyrite ± tetrahedrite vein networks with Sb, As, Ag, and Zn anomalies in the uppermost zone, to a Cu-depleted pyrite-rich envelope with Co anomalies, and finally to late, barren calcite veins in distal zones."

Jan 1, 2007

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By D. P. Fenton

The Phelps Dodge El Paso Rod Mill produces approximately 2.4 million pounds per day of copper rod from a casting and rolling operation. The newly formed rod is treated to remove mill scale and oxides using a sulfuric acid and hydrogen peroxide solution which is bled periodically when the copper concentration reaches 30-35 g/L. The bleed solution is heated to 75° C to destroy the residual peroxide. Copper is then recovered in a 270 cell EMEW electrowinning plant. Clean acid is also regenerated in the EMEW plant and is returned to the rod cleaning circuit. The EMEW plant commissioned in January 2006, has two operators and replaces a copper sulfate plant with fourteen operators. The EMEW plant has a capacity of 1700 kg/day of cathode copper at 2.1 kWh/kg copper deposited. The electrowinning plant operates in closed circuit with the rod mill returning up to 2600 kg/day of sulfuric acid resulting in zero discharge. Use of dimensionally stable anodes (DSA®) ensures that the acid quality is maintained in the closed loop operation. The operating conditions, performance and plant experience of the EMEW copper and acid recovery plant are discussed.

Jan 1, 2007

Ravensthorpe Nickel Operation (RNO) is a major new mine and processing plant currently being constructed by BHP Billiton in a ?green field? site near the small town of Ravensthorpe, about 150 km west of Esperance and six hours drive from Perth in Western Australia. Ensuring that the project has a positive overall impact on the surrounding region and that this extends well beyond the life of the operation will be a major challenge for RNO, state and local government, and the local community. For the last two years, the Centre for Social Responsibility in Mining (CSRM) has been assisting RNO management and the RNO Community Liaison Committee to develop a community sustainability monitoring framework for the project. This paper reports on the process that was used to develop the framework, describes the main elements and briefly discusses key learnings from the exercise.

Jan 1, 2007

By S. Garcia, J. Gebhardt, D. McBride, A. Hernandez, A. Esplín, M. Cross

The Minera Yanacocha operation consists of several heaps interconnected with ponds and gold recovery plants and presents various operating challenges. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters and inventory issues. An integral component of the process water/mass balance is a model of each heap that describes heap behavior based on the individual characteristics of the heap. The heap models are linked to a mass balancing program in order to track flows and concentrations throughout the circuit. A case study of the process heap model is presented for the La Quinua heap, including results for the normal base line operation and several operational problems such as loss of solution flow to the heap (i.e., pump failure), increased flow to a section of the heap (i.e., pond volume control), effect of significant rain events, and impact of a change in material properties (i.e., change in ore type). The impact on heap operating efficiency is discussed with regard to effects on recovery and gold solution grades.

Jan 1, 2007