Search Documents

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

By John J. Sammarco

Miners depend most heavily on visual cues to recognize underground mining hazards; consequently, illumination plays a critical role in miners? safety. Some hazards are located in the miners? peripheral field-of-view (10 degrees to about 60 degrees off-axis) or on-axis (0 degrees). The objective of this research was to determine if there were visual performance improvements when using solid-state cap lamps with light-emitting diodes (LEDs) as compared to incandescent light bulbs commonly used in miner cap lamps. Recent research has indicated that an increased short-wavelength content of the spectral power distribution of LEDs relative to incandescent lamps improves peripheral visual performance for low-light (mesopic) conditions. The visual performances of nine subjects were quantified by measuring the subjects? speed and accuracy in detecting floor objects located on axis and at ±20 degrees off axis. The objects were located near field (1.83 meters) and far field (3.66 meters). Upon presentation of the objects, subjects would count and point to each object using a red-laser pointer. The object detection response time and number of missed objects were recorded. The results of the visual performance comparison for an LED, a prototype LED, and an incandescent cap lamp are presented. There we no missed objects when subjects used the LED-based cap lamps but, there were three missed object occurrences when subjects used the incandescent cap lamp. The mean detection time when using the incandescent cap lamp was 55.3% greater than the prototype LED cap lamp and 43.5% greater than the LED cap lamp. It can be inferred from this data that the spectral distribution of LED-based cap lamps could enable significant visual performance improvements as compared to incandescent cap lamps1.

Jan 1, 2007

By W. J. Vlasblom, A. M. Talmon, A. J. Nobel

In initial laboratory tests with a travelling submerged jet on artificially prepared clay it was found that the cavity depth is dependent on the stagnation pressure of the jet and the undrained shear strength of the clay. In addition, it has been observed that the increase in cavity depth with jet pressure is stronger at higher jet pressures. It is assumed that this can be explained by cavitation of the jet at higher jet pressures. At cavitation a cone of bubbles is formed around the jet, which reduces the exchange of momentum between the jet and the surrounding water. This results in a higher jet velocity and a higher stagnation pressure at a specified distance from the nozzle exit. In literature, no relation between the jet pressure of a free submerged cavitating jet and stagnation pressures was found. Additional tests were carried out to determine this relationship. Because practical dredging occurs at relatively large water depths, these tests were performed in a pressure vessel at different pressure levels. It is concluded that the efficiency of a jet (defined as the stagnation pressure at a certain distance divided by the jet pressure), for stand-off-distances smaller than 45 times the nozzle diameter, increases significantly by cavitation in comparison to the non-cavitating situation. However, the jet pressure required for a fully developed cavitation cone increases strongly with water depth. At dredging depths of 20 m and more, the necessary jet pressures are higher than normally applied in dredging practice. Thus in spite of the importance of cavitation in laboratory tests at atmospheric pressure, in normal dredging practice cavitation is of less importance.

Jan 1, 2007

Using a series-model of an automotive short range radar sensor (SRR) and a recently completed experimental radar system, field tests have been performed in a surface mine. It was examined, to what extent low-cost electronically scanning radar sensors can provide useful data for assistance systems on large scale mining machines. Simple sensors are useful for anti-collision safety zones or hopper car automation. The more complex and sophisticated experimental radar system using digital beam-forming can clearly detect and map the contours of trenches and slopes. The overall promising results refer to many more potential applications for electronically scanning radar in surface and underground mining as a reliable alternative to mechanical laser scanners.

Jan 1, 2007

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the project's life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: How do mill lifters and liners really work and have an effect on grinding? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the æextremeÆ form the major observations and conclusions expressed in this paper are that: the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; the often promoted theory that balls impacting the ætoe of the chargeÆ is a dominant form of breakage is incorrect; and fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By M. Sagedahl

The off gas from a smelter is cooled and dust removed in an electrostatic precipitator before approximately 95% of the sulphur dioxide (S02) is converted to sulfuric acid. However, the tail gas may need to be polished to remove the rest S02 to meet demands. A flue gas desulphurization (FGD) system, as usually applied to S02 removal on coal and oil fired Power Station, is suitable for polishing tail gases from copper smelters. The ALSTOM Seawater FGD process makes use of the alkalinity in the seawater to absorb and neutralize S02. Before being returned to the sea, the seawater is treated to comply with environmental regulations. As the ALSTOM Seawater FGD process uses no reagent and produces no byproduct, it is extremely cost-effective for coastal installations. The first SWFGD plant started operation in 1968. Over 60 of these units have been installed worldwide. The ALSTOM Seawater FGD process removes S02 from flue gas flows corresponding to a total of 70,000,000 Nm3 /h. Suitable for thermal power stations, smelters and oil refineries, ALSTOM Seawater FGD plants efficiently treats flue gases in the range of 300,000 Nm3/h to 2, 700,000 Nm3 /h per FGD plant, containing 20 - 6,500 ppm of S02.

Jan 1, 2007

By A. C. Atenas

The majority of refineries that operate with traditional starting sheet technology ?starting sheet- uses a relatively low current density of 250 A/m2. Industrial tests at high current density with conventional technology were carried out in Refinery of Potrerillos, getting satisfactory results that are similar the results obtained with permanent cathode technology. The series of copper refining electrolyses electrolysis trials were carried out between 300 to 325 A/m2. Electrolysis conditions, in accordance with industrial practice, were kept constant in all sets of experiments and were as follows; 45 g/L Cu 2+, 210 g/L H2SO4, 62 °C, electrolyte circulation of 14-18 L/min. The same Dosing dosing of Additives additives used in permanent cathode technology was required in these tests. In general, only not importantminor operational modifications were necessary in comparison to normal practice in the Refinery to assure the good results. Different quality of starting sheet and anodes were examined. The test included starting sheets from smelter and laminated process. Results indicate that the charge physical quality of the electrodes and the control of the process during the two first days of operation are the keys to get the best results.

Jan 1, 2007

By Richard Arsenault

The production of oil & gas from wells requires method of flow from the producing formation into the well bore. Once the well is drilled it will have casing pipe installed to protect the integrity of the well formations and means of delivery to the surface. Once casing pipe is installed it will be cemented in by pumping cement through the annulus of the casing pipe down to the bottom of the well and allowed to flow outside the casing pipe up into the formation.

Jan 1, 2007

By J Vann

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and û importantly û metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These ægeometallurgical variablesÆ drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many ætraditionalÆ (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

By Ch. Roumpos

The present contribution investigates the way of applying benchmarking for large-scale open-pit mining operations based on sustainability indicators proposed by numerous institutions or groups of experts. These indicators have been developed taking into consideration the legal and regulatory framework that are in force. However, their scope is not only to declare the mining company?s compliance with all legal requirements but also to represent its economic, environmental, and social performance. In this way, sustainability indicators allow assessment of a company?s capacity to produce commodities, to meet the environmental quality requirements and to contribute to a long-term economic, cultural and social development of the local communities.

Jan 1, 2007

Things are going well in the mining and construction industries world-wide. So good are things that from April 23 to 29 more than 500,000 visitors involved in those two industries attended the bauma 2007 Trade Show in Munich, Germany. Bauma is an international trade fair for construction and mining equipment that took place at the New Munich Trade Fair Center. It is hosted by Munich once every three years. This year was the most successful bauma ever and further strengthened the shows position as the world leader in the field.

Jan 1, 2007

By Patrick E. Durnal, Henrik Dahl

"A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM + Harris) designed the $779 million seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofi t was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with the support of various consultants. MARINE FOUNDATION RETROFIT SCOPEThe retrofi t design of the submerged foundations included:??A total of 476 tension and compression micro piles (290- 1140 kips or 1290-5071 kN) installed through cored holes through the underwater bells at 31 pier locations??Fourteen 126/150/164 inch (3.20/3.81/4.17m) diameter CISS (Cast-in-steel shell) concrete shear piles (1160- 2660 kips or 5160-11832 kN) installed through new precast concrete pile cap extensions??Twelve CIDH (Cast-in-drilled-hole) shear piles (1060- 2130 kips or 4715-9475 kN) with 150 inch (3.91m) diameter steel shells to top of bedrock and 30 ft (9,14m) long and 11 ft (3.35m) diameter rock socket installed through new precast concrete pile cap extensions The specifi ed post bid test boring revealed deeper bedrock at one pier location allowing deletion of the rock socket. Thus 15 CISS and 11 CIDH shear piles were installed at 11 pier locations - 9 piers with 2 piles and 2 piers with 4 piles. Cut off elevations for the shear piles ranged from 46 ft to 60 ft (14.0m to 18.3m) below mean sea level and cut off for the micro piles was 8 ft to 46 ft (2.44m to 14.0m) below mean sea level. Almost all foundation retrofi ts required work under limited headroom conditions. Underwater construction connections required innovative design details and construction techniques for each pile type. The 11 piers had 22 precast concrete pile cap extensions installed in pairs and connected by either tremie concrete closure pours or by large pipe struts. The precast pile cap extensions were strapped underwater using large steel bands wrapping around the belled piers with grouted annulus. The precast pile caps were founded with 14 inch (355mm) diameter steel pipe piles, which were either support piles or seismic tension and compression piles. The seismic piles were connected in grouted corrugated steel pipe sleeves cast into the new concrete pile caps."

Jan 1, 2007

By P. De Kock

Strategic mine planning is concerned with the decisions that determine the value of the business, while tactical planning deals with the tasks to realize that value. When tasked with formulating a strategic mine plan, the mining engineer often turns to commercially available software. However, these software packages have limited applicability to the RBM situation. Adopting a simpler, back to basics approach founded on a deep understanding of the economics of the orebody has the advantage of providing a clear logic to guide tactical planning. By creating a coherency between strategic mine planning, and tactical planning the likelihood of successfully executing the plans and attaining the value promised by the strategic plan is increased. This paper describes the reasons why RBM embarked on a strategic mine planning process, the rationale of choosing the process, and the process itself.

Jan 1, 2007

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007

By Pieter de Waal

The use of valuable minerals is a necessity to maintain a modern society. Not only the iron, aluminium, coal and oil that are used in large quantities, but also the uranium, copper, vanadium, tungsten, antimony and many others play an essential role in the bigger picture of our modern civilisation. Minerals occur in a form and in places determined by a long history starting at the dawn of creation. Over billions of years the elements have combined in wondrous combinations and structures. They have been broken up by massive explosions, movements in the earth's crust and erosion by wind and water. They have been restructured and recreated in even more configurations by the application of heat and pressure, leached by and exposed to new chemical compounds. The result is that most valuable minerals are found in impure form and mixed up with other, less useful waste material. 2. Mineral Beneficiation The processes used for the purification and enhancement of an ore, to satisfy the needs of downstream applications, are collectively referred to as mineral beneficiation. Mineral Beneficiation starts in the mine where only that portion of the ore, that can be economically processed, is selectively extracted. It may also include ore blending, to ensure a more consistent feed to the following stage of valuable mineral recovery. The next stage in mineral beneficiation is the liberation of the valuable minerals from the gangue. This is achieved by blasting, crushing, milling and grinding down to an adequately fine grain size to facilitate good separation. Separation can be achieved by a variety of different techniques. ?Screening coarse from fine particles is an easy method if the valuable mineral is dominant in a certain screen fraction. ?Magnetic separators can differentiate minerals on the basis of their difference in magnetic susceptibility. ? Electrostatic separators differentiate on the basis of electrical conductivity. ? The differences in density are exploited in spirals and jigs. ? Particular surface properties provide a separation technique in flotation. ?The selective sorption properties of a collector medium are another option.

Jan 1, 2007

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007