Search Documents

By A. K. Majumder

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of coal fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of coal fines. The results obtained from this study revealed that among the parameters studied, drum rotation and feed solids concentration play dominating roles in controlling the yield and ash content of the clean coal. Mathematical modeling equations that correlate the variables studied and the yield and ash contents of the clean coal were developed to predict the performance of an MGS under different operating and design conditions. The entire exercise revealed that the MGS could produce a clean coal with an ash content of 14.67% and a yield of 71.23% from a feed coal having an ash content of 24.61%.

Jan 1, 2007

By Jeffrey M. Listak

The Respiratory Hazards Control Branch of NIOSH routinely conducts laboratory and mine-site evaluations of dust control technologies. Gravimetric and instantaneous dust sampling instruments are used in these evaluations to measure and document dust levels to determine worker exposure. The Thermo personal DataRam (pDR) is an instantaneous sampler that uses light-scattering technology to provide relative measures of airborne respirable dust. The pDR can be used in active and passive modes to measure respirable dust levels. Tests were conducted to evaluate the sampling performance of active and passive pDR operation relative to each other and. against a gravimetric sampler (the accepted standard for respirable dust measurement). The purpose of the test was to determine if the pDR can be used effectively in the passive mode in higher velocity airflows (up to 5.1 m/s (1000 fpm)). Studies of the pDRs in both modes of operation were conducted in a controlled laboratory environment and in field situations. Dust measurements using pDR units in both modes of operation were recorded in ve¬locities ranging from 1.0 to 5.1 m/s (200 to 1000 fpm). Tests were conducted in ambi¬ent air and in air with the addition of moisture. Results show that, although the units measure different concentrations in their respective modes of operation as compared to a gravimetric sample, the relative readings can be corrected to yield accurate dust measurements.

Jan 1, 2007

By Z. Gostynski

The paper is a historical cross-section through a 28-year period of operation of the direct-to-blister Flash Smelting Furnace in the KGHM Glogów Copper Plant. It presents the origin of the furnace as well as the path of numerous changes and modifications both in technology and process introduced in the furnace in response to the production and cost-reduction challenges. The authors provide justification of the statement that continuous improvement of the "Polish" Flash Smelting Furnace has ranked it among the most modem smelting units in the world.

Jan 1, 2007

By H. Lowers, B. Van Gosen

The Iron Hill (Powderhorn) carbonatite complex is a 31 km2 alkalic intrusion located about 35 km south-southwest of Gunnison, Colorado. The intrusion has been well studied and described because of its classic petrology and architecture of a carbonatite-alkalic complex. The complex is also noteworthy because it contains enrichments of titanium, rare earth elements, thorium, niobium (columbium), vanadium, and deposits of vermiculite and nepheline syenite. In particular, the complex is thought to host the largest titanium and niobium resources in the United States, although neither has been developed. It may be economic to extract multiple resources from this complex with a well coordinated mine and mill plan.

Jan 1, 2007

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By O. Schnake, M. Isakson, C. A. Landolt

The paper presents the conceptual basis for the development of an Activity Based Costing system (ABC) for the analysis and estimation of process costs in mining and metallurgy. In particular, it discusses three major thrusts towards attaining increased efficiency in extraction and processing systems: (a) understanding the link between process and expenses, (b) identifying the chemical and physical factors that govern process costs and ( c) using process and cost models of the production systems. The authors have developed computer techniques to analyze data from conventional accounting and apply them to the development of process based ABC systems. The cost causing activities are linked to management units patterned after the organizational structure of the production system. All costs are associated with specific process functions such as charge preparation, smelting, refining, etc. The level of detail is determined by the quality of data available in conventional accounting systems. The system permits data analysis of historical cases and the projection of costs for new production schemes. Results can be presented in various levels of aggregation, following organizational and/or functional structures. The outputs of the system are tabular and graphical, typically following Pareto analysis concepts.

Jan 1, 2007

Building aggregates, basic materials for the construction industry, must be produced according to socio-economic and environmental sustainability principles, i.e. the three fundamental components of Sustainable Development. On this subject, an introductory discussion about the interpretation of these concepts in the field of mineral production and construction industry is first presented. As for the socio-economic aspect, aggregates are then illustrated as being essential resources for the development of the society, underlying that it is possible to understand their fundamental socio-economic role only through the analysis of the whole product life cycle, from production to end use and beyond. The same has to be done on the environmental side to assess the environmental impacts of aggregates: one should look for, not in the quarry phase only, but also in all the downstream activities of the construction process, including the use phase and beyond. Based on this approach, in the second part of the paper, the results of some investigations focused on eco-profiles of building aggregates, gathered through the application of LCA methodology are presented and discussed. In such a context, strengths and weaknesses of LCA indicators will be discussed, as well.

Jan 1, 2007

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By N. Dahata

B206 aluminum?copper alloy has a potential for wider use in the automotive industry due to its light weight and relatively superior mechanical properties as compared to aluminum-silicon alloys. The possibility of casting this alloy via Lost Foam Casting (LFC) has not been investigated in detail. Therefore, the effects of foam types (T170B standard untreated EPS and T175-brominated EPS), coating types (Styro Shield 5553 and Styro Shield 5554), copper level (4.5 wt % and 5.0 wt %) and titanium levels (0.5 wt % and 0.25 wt %) were related to fillability, microstructure and microporosity. The metal velocity in T175 EPS pattern was higher than that in T170B EPS pattern. For T175 EPS pattern, the total solidification time was 3% higher and the loss of temperature for decomposition of EPS was lower than those in the case of T170B EPS pattern. The grain size, porosity level and maximum pore size were quantified using Light Optical Microscopy (LOM) and image analysis. The casting with T175 EPS pattern showed larger grain size relative to that with T170B EPS pattern. The porosity level and the maximum pore size decreased significantly when the titanium level was increased from 0.05 wt % to 0.25 wt %.

Jan 1, 2007

By Dave P. Cooper, Tim D. Burgess, Dean H. Ambrose

This paper discusses the application of digital human models (DHM) to examine computer generated forces necessary to move specific joysticks by using roof bolter virtual operators to predict the forces experienced on the operator’s upper extremities. Using DHM and simulations of static movements, investigators analyzed predictions of joint moment and joint force effects on virtual operator’s right wrist, elbow and shoulder and compared them to different body dimensions and work postures. This study exemplifies the ease of estimating upper extremity loads on equipment operators using virtual operators and computer models of equipment and work environment. As expected, comparing results of percentage of joint force and moment reduction using the electronic control and of the mechanical control showed that the electronic control had lower joint forces and joint moments over the mechanical control. The average predicted value of the joint moment on the wrist was 1.84 Nm, elbow 7.85 Nm and shoulder 14.55 Nm and of the joint force on the wrist was 5.06 N, elbow 4.56 N, and shoulder 3.67 N. Because the data illustrates low-level forces to move a joystick, inadvertent actuation of the control is addressed. Regardless of the findings, research is still needed on joysticks in real world situations such as an epidemiological assessment of equipment operators in the field before final recommendations and conclusions can be drawn.

Jan 1, 2007

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development teamÆs processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement.TSG Consulting advocates a ætotal integrated system approachÆ to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By C. N. Harman, N. S. S. Rama Rao

Production of Ferro-alloys through submerged electric arc furnace involves use of electric power as one of the major inputs. Hence the production by this power intensive process can be made economically more competitive if the specific power requirement for smelting each ton of the product is brought down. This becomes all the more necessary where the power cost is comparatively high, like in India. Since the day FACOR started production of Ferro Chrome in 1968, briquetted chromite fines along with lumpy ores were used as feed. Subsequently the increase in the proportion of briquettes and reduction in lumpy ore helped in increasing the use of chromite fines and also brought down the specific power requirement. Meantime FACOR had been closely watching the technical development of use of sintered pellets in Outokumpu and SRC Processes which need still lower specific power. But the high capital requirement for a pelletisation plant kept FACOR from introducing pellets feed to their Ferro chrome furnaces. So this was postponed to be adopted in future. In February 2004 in the ?1st Ferro-Alloys India?, a paper [1] was presented by Dr. Amit Chatterjee. In the questions period after the presentation of the paper there came up a discussion in which it was revealed that with the Indian high grade chrome ores it was not possible to make sufficiently strong pellets, unless a larger percentage of bentonite is used as binder. This is because the Indian high grade Chrome ores have different mineralogy of gangue content compared to low grade ores in Finland and South Africa. Higher usage of bentonite gives rise to higher slag volume and this would result in increased specific power. Since FACOR had plans to go in future for sintered pellets feed, this gave rise to a doubt on success of pelletisation for Indian high-grade chrome ores. This prompted FACOR to take up experimental production of sintered chromite pellets and use of the same in one of their existing furnaces for production of high carbon Ferro chrome. The results are encouraging and are summarized in the paper.

Jan 1, 2007

By F. Parada

During copper smelting and converting processes, slag generated is pyrometallurgically cleaned and then disposed, containing around 1 % of this metal. However, important amount of molybdenum initially contained in concentrates also goes to the slag phase. Research on molybdenum recovery from water granulated slags using acid leaching at low temperatures was conducted to find an efficient way for molybdenum extraction with lower magnetite in the slag. However because of the high fayalite content high acid consumption was found. Molybdenum can be recovered from solution using ionic exchange resins, but high silica content interferes with extraction. Some studies addressed to minimize silica extraction as well as alternatives of selective silica precipitation in order to develop a technically feasible process.

Jan 1, 2007

By W. J. Adams

It is recognized that within life cycle assessment that the eco-toxicity potentials (TPs) derived for metals require additional research to improve their reliability. Current models used to develop TPs do not include important fate process for metals such as speciation and bioavailability. Toxicity potentials are standard values used in LCA to enable a comparison of potential toxic impacts between substances. Huijbrechts (2001) calculated toxicity potentials for 181 substances utilizing the USES model for six impact categories, i.e. freshwater aquatic ecotoxicity, marine aquatic ecotoxicity, freshwater sediment ecotoxicity, marine sediment ecotoxicity, terrestrial ecotoxicity and human toxicity (not considered here). Marine ecotox potential for metals is typically high using this approach, whereas most open ocean metal concentrations are very low. A sensitivity analysis of the USES-LCA model was undertaken using copper as an example. Results indicate: fate processes on the global scale are driving the marine water and sediment TPs for copper most; the second most important fate parameter is sedimentation from the water and burial in deep sediment layers; inclusion of speciation and bio-availability processes would be very beneficial; more accurate estimates of input parameters should be used, and the PNECwater and PNECsediment and all partition coefficients for metals should be updated in the model.

Jan 1, 2007

By Lawrence M. Zanko

Eighteen coarse taconite tailings samples were collected in 2000-2001 from five western Mesabi Range taconite (iron ore) operations located in northern Minnesota, i.e., EVTAC, Hibbing Taconite (Hibtac), USX Minntac, Ispat Inland (Minorca), and National Steel Pellet Company (NSPC), to test their physical, geological, chemical, and mineralogical properties [Zanko, L.M., Niles, H.B., Oreskovich, J.A., 2003. Properties and aggregate potential of coarse taconite tailings from five Minnesota taconite operations, Minnesota Department of Transportation, Local Road Research Board, St. Paul, MN, Report No. 2004-06 (also as Natural Resources Research Institute technical report, NRRI/TR-2003/44)]. The goal was to assemble a body of technical data that could be used to better assess the potential of using a crushed taconite mining byproduct like coarse tailings for more widespread construction aggregate purposes, primarily in roads and high¬ways. An important part of the mineralogical assessment included X-ray diffraction (XRD) analyses and microscopic (polarized light microscopy, scanning electron microscopy, and transmission electron microscopy, i.e., PLM, SEM, and TEM, respectively) evaluation of the size and shape (morphological) characteristics of potentially respirable microscopic mineral particles and fragments. Quantitative mineralogy, based on XRD analyses, showed that the dominant mineral in all samples was quartz (55-60%), followed by much smaller amounts of iron oxides, carbonates, and silicates. Specialized microscopic analyses and testing performed by the RJ Lee Group, Monroeville, PA, on both pulverized (-200 mesh, or 0.075 mm) and as-is sample composites showed that no regulated asbestos minerals or amphibole minerals were detected in the western Mesabi Range samples. A small number (26) of non-asbestos and non¬amphibole mineral cleavage fragments/mineral fibers were detected by SEM out of 1000 fields analyzed, but most were identified as min¬nesotaite and talc, silicate minerals common to the Biwabik Iron Formation. Amphibole minerals, absent in coarse tailings samples from the five western Mesabi Range taconite operations, were present in a single eastern Biwabik Iron Formation sample collected in 2003 for Lake County from the Cliffs Northshore operation in Silver Bay, MN. Importantly, the Superfund Method for the Determination of Releasable Asbestos in Soils and Bulk Materials [United States Environ¬mental Protection Agency (USEPA), 1997. Superfund method for the determination of releasable asbestos in soils and bulk materials, EPA 540-R-97-028, U.S. Environmental Protection Agency, Washington], as modified by Berman and Kolk [Berman, D.W., Kolk, A.J., 2000. Modified elutriator method for the determination of asbestos in soils and bulk materials, Revision 1: Submitted to the U.S. Envi¬ronmental Protection Agency, Region 8, May 23, 2000] failed to generate any protocol fibers, i.e., fibers longer than 5 µm and thinner than 0.5 µm, from either the western coarse tailings samples or the single eastern Biwabik Iron Formation sample. The combined findings suggest coarse tailings and other taconite mining byproducts should be treated with the same common sense safety and industrial hygiene approach practiced for all mineral-based materials that have the potential to generate respirable dust. © 2007 Elsevier Inc. All rights reserved.

Jan 1, 2007

By K. Oishi

We have developed a 76Cu-3Si-21Zn alloy "ECOBRASS®" containing no lead. When 3% Si is added to a 78Cu-22Zn alloy, kappa and gamma phases participate uniformly in the alpha matrix. When being machined, stress concentrates on these hard phases, namely kappa and gamma, and thereby lowering the required cutting force and yielding segmentalized chips without lubricant. Kappa and gamma phases transform into beta phase under high temperature, which makes it easier to extrude and/or forge the alloy. When 0.08% P and 50 ppm Zr are co-added, the grains of ECOBRASS® castings are refined significantly to become as small as several dozens of micrometers. The grain refinement by the co-addition of P and Zr improves castability, tensile strength and elongation of ECOBRASS® castings. Meanwhile, the lead leachate from an ECOBRASS® water meter, field-tested in pH 6.8 drinking water for one year, was less than 5 ppb without correction. No indication of dezincification corrosion was observed, either. ECOBRASS® is equally suitable for rods, forgings and castings, and makes it possible to produce a complete set of plumbing parts (valves, faucets, etc.) by its own. This way, not only improving recyclability, ECOBRASS® also realizes size and weight reduction due to its good corrosion resistance and high strength.

Jan 1, 2007

The blasting of the 2190_6095 stope at Kimberley Nickel MineÆs Sally Malay operation in Western Australia is an example of what can be achieved with electronic detonating systems when a drill and blast engineering team is faced with complex blast geometry and a major pump station in close proximity to the stope. Using Dyno NobelÆs HotShotÖ system, the engineering team successfully designed and initiated the 36.5 Kt stope firing, with a powder factor of 0.35, resulting in no damage to the pump infrastructure, better fragmentation of the ore and less overbreak in what had previously been a geotechnical and geometrically challenging stoping environment. This paper will discuss the design parameters used for this stope blast as well as the benefits the operation found in using precision detonator timing in this 252 hole shot over two levels using a combination of up and down and slashing rings that were initiated in four different directions.

Jan 1, 2007

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By D Craw

The Hyde Macraes Shear Zone is a mineralised low-angle shear within the Otago Schist traceable for ~30 km with a NW strike. It is been actively mined along 12km of this strike, producing >6 Moz of gold. The shear zone consists of greenschist facies rocks with a mineralogy only subtly different from that of the host schist. Pervasive fluid flow has occurred along grain boundaries and within microshears which have been enhanced by the deposition of hydrothermal graphite. We model the development of these microshears using a threedimensional numerical code. For an inhomogeneous initial rock with lithostatic fluid pressures and a dynamic permeability deformed under dextral non-coaxial flow, deformation is distributed into weak shear bands. Graphite deposition and associated reaction-softening has a dramatic effect on the development of model shear zones. Graphite is deposited into a shear band, weakening it and further localising the deformation into that shear band, producing an anastomosing and interconnected shear zone structure such as observed in the HMSZ. The degree of graphite precipitation and graphitic-induced weakening are varied in the models. More graphite precipitation with a low degree of reaction-softening results in more diffuse shear bands. In contrast less graphite deposition but with a high degree of reaction-softening more leads to the development of more focused shear bands. Graphite deposition has clearly controlled the formation of the HMSZ structure, and is an important indicator of potentially mineralised structures elsewhere.

Jan 1, 2007

By M. Matsuda

The Hitachi refinery of Nikko Smelting & Refining Co. Ltd. began its electrolytic copper refining operations in 1911. In December 2002, the refinery changed its operation scheme by introducing the ISA permanent cathode technology for the first time in Japan. The change resulted in higher productivity, better cathode quality, and lower operational costs. The operation has been continuously improved to reach a 20% higher production capacity than the original one. For the electrolyte purification process, the Hitachi refinery has developed a new process for removing impurities. The process involves As, Sb and Bi adsorption from the electrolyte by means of chelating and ion exchange resin. The new resin process will achieve higher efficiency in removing impurity.

Jan 1, 2007