Search Documents

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

There are many different challenges when sampling mineral commodities. Sampling is part of many decision-making processes, from control of the number of drops of a reagent to all aspects involved in determining how much to pay for a mineral consignment. However, if all decisions must be supported by correct assumptions, or at least agreed terms, how can this be guaranteed? The main approach is to emphasise the importance of continuous surveying of sampling practices. If they are based on non-recommended protocols, this raises concerns. In addition, safety failures and lack of appropriate behaviour from the technical perspective can lead to disasters, both from the human and business perspectives. Impacts on safety and health are clearly unacceptable. It should be noted that imperfect safety and health practices in sampling operations have a strange correlation with incorrect sampling techniques. The commercial interface can also be affected. Companies have studied extensively the various aspects of measuring quality parameters for mineral commodities to understand the risks for investors and owners, and they take decisions that fundamentally respect the interests of parties in contracts and not result in losses. Every result should be obtained in defensible ways, and neither losses nor profits taken in indefensible ways. Most of such situations are related to bias; a significant systematic difference between a measured value and a reference value for a contractual quality parameter. Bias is always undesirable, because it always implies an incorrect advantage for one party and without doubt an undesired disadvantage for the other party. These situations are solved financially through a third-party arbitrator becoming involved in delicate situations, such as a commercial claim, but the outcome is always tangibly or intangibly bad for one of the parties. Another possibility is a permanent or temporary loss of precision. Poor precision, due its nature, generates reasonably balanced losses and profits, but it may hide out-of-control situations, generate instability and induce financial losses due to actions taken towards clearing commercial disputes involving interlaboratory programs, sample exchanges and duplicated sampling and sample preparation procedures, in the end wasting time and resources and creating a permanent source of commercial tension. While bias situations demand immediate adjustments for correctness, poor precision has to be understood as something that cannot be just calibrated out and is a situation that demands investment of time and effort. Precision optimisation has to take into account best practice for obtaining the required precision as well as cost/benefit analysis studies. Purchasers, engineers, salesmen and all personnel need to recognise that sampling is a major area to understand when taking decisions. The aim is to spread concepts that can really help, such as simple in-house actions to improve productivity and completion of surveys on commercial sampling operations, in order to ensure correct results are obtained and assertively take corrective actions, thereby establishing a healthy relationship with investors, suppliers and purchasers and in the process optimising the business.

Jan 1, 2008

By B. Thompson

"1. AbstractMagnesium alloys have been successfully recycled for decades and have won acceptance for use by die casters and most of the automotive industry. As the supply chain for magnesium and magnesium alloys continues to change, due to the consolidation of producers, it is essential that quality control methods be closely examined with each new supplier added. An examination of the various process steps that are needed to assure quality in the final product will be discussed thus giving a basis for the auditing of new magnesium suppliers.2. IntroductionMagnesium recycling in the past has been somewhat limited due to its use more as an alloying agent for aluminum based alloys and as a desulfurization agent in iron and steel than in more readily recycled structural products. Recycling efforts continue to improve as more production is finding its way into automotive structural components, hand tools, and a variety of computer and cellular telephone applications.With the closure of several large North American primary magnesium production facilities over the past decade we have only recently witnessed a tightness in supply that is driving magnesium prices significantly higher, nearly doubling the price in the last year alone. The rapid escalation in pricing will provide additional economic incentives to fully utilize recycling for the recovery of an even greater percentage of both old and new sources of magnesium scrap. Political pressure continues to intensify towards the secondary recovery of any and all recoverable resources of which magnesium recycling readily applies.Economics will also likely drive the development of new sources of magnesium production, both from primary and secondary production. As new sources of magnesium are offered to the marketplace the potential for product quality issues may increase. When considering any new raw material supplier a decision must be made as to the impact of defective material on the intermediate or finished product. Quality defects in magnesium ingot can result in a variety of appearance, corrosion, and even adverse structural effects in the finished product. The potential severity of the impact of defective raw materials on the finished product will determine and often justify a close look at any new supplier. An on-site audit of a new supplier of a critical raw material is often justified to ensure that an adequate quality assurance system is in place. We will now look at a number of key production points that should be examined during an on-site audit that have can have an impact on the overall quality of the finished product."

Jan 1, 2008

By D A. Collins

The floatability methodology developed by the AMIRA P9 project through research contributions by the Julius Kruttschnitt Minerals Research Centre (JKMRC, Brisbane, Australia), University of Cape Town (UCT, Cape Town, South Africa) and McGill University (Montreal, Canada) has been successfully commercialised through JKTech. The methodology involves detailed flotation plant campaigns which require large quantities of data to fit models that can be used in JKSimFloat (a steady state simulator for the flotation process). The methodology to date, although widely accepted as the best flotation optimisation technology available, is limited to existing circuit optimisation and requires full plant or pilot plant data to calibrate new models. The floatability of new ore types cannot be characterised using this method unless a pilot campaign is undertaken. After reviewing a large database of existing industrial floatability data, a new methodology is proposed that involves a laboratory based flotation test procedure and review of the floatability database to characterise the floatability of new ores. The full methodology is labelled the floatability index test procedure (JKFIT). This paper outlines the JKFIT procedure and the results of applying this methodology to pilot plant data from a copper ore. JKFIT was applied to two different feed sizes (namely a P80 of 180 microns and 212 microns) of this copper ore. The results of applying JKFIT to this case showed that the metallurgical response (in terms of grade and recovery) from the full pilot plant survey data could be predicted well. Further validation of this methodology was conducted on a separate copper ore. The results from this validation also showed that the JKFIT test was able to be used to predict the full plant performance. The JKFIT test has the potential to become the 'drop weight' test of flotation which will improve the confidence in plant design flow sheet layouts, allow full orebody characterisation and prediction of key grades and recoveries before the ore enters the plant, and will provide an improved methodology for chemistry impact analysis on different ores.

Jan 1, 2008

By R Berry, N Bonnici, K Nguyen, S G. Walters, M Kamenetsky, C L. Evans

Mineral maps produced via optical and scanning electron microscope û mineral liberation analyser (SEM-MLA) automated mineral identification systems are being used to examine the relationships between mineral phases in spatially well-constrained samples of intact and crushed rock. The use of sophisticated image analysis software allows data pertaining to individual or groups of mineral phases to be extracted from the mineral maps. Analyses of the extracted data can be used to identify populations of phases. Data extracted from the images can be compared with mineral processing data, eg hardness, grindability, degree of liberation, from the same sampling intervals, enabling ore characterisation to be linked to processing behaviours in a spatially constrained, quantified manner that can potentially assist with mine planning and optimisation.

Jan 1, 2008

By Glenn K. Nolan

"Today, more than any other time in recent history, aboriginal communities are looking for ways to be understood as more resource development companies continue to explore and develop Canada's vast resource potential.Recent Supreme Court rulings have affirmed the need to engage aboriginal communities early on in resource development projects. There are many conflicting ideas on how, who, and when to engage. Given the large number of communities and varied cultures, each resource development company must equip itself with a better understanding of the people they are planning to work with.The lecture will begin with a basic historical perspective on treaties and the various societies across Canada. We will also explore the current situation many communities find themselves in today. Building a meaningful relationship with a community is the foundation for a lasting partnership. Every community is unique and every approach to engage communities must be just as unique. The lecture will outline some basic steps that can lead to a better relationship building process between the communities and companies."

Jan 1, 2008

By Ali Kucuk, Bekir Karasu, Keriman Karaveli Pekkan

"Zircon (zirconium silicate) is the main opacifier of glossy, opaque, white colored, frit-based wall tile glazes. However, zirconia containing frits employed in the preparation of these glazes increase the production cost and therefore, limit zircon usage as a raw material at industrial scale. With the present study, it was searched whether borax solid wastes could be evaluated as a component in the starting relevant frit recipes. The wastes were obtained from Eti Maden Kirka Boron Company of Turkiye. Frit production, glaze preparation, application, and fast single-firing of glazed wall tiles were conducted under laboratory working conditions in Anadolu University, Department of Materials Science and Engineering laboratories. Beside standard tests applied to the final glazed wall tiles, color and gloss analyses of the fired glazes were conducted with a spectrophoto-meter and a gloss-meter. Characterization of these newly produced glass-ceramic glazes was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques. IntroductionFrits are the indispensable constituents of most industrial glazes which mature at temperatures below 1150 °C [1]. In the traditional opaque glazes used in wall tile industry, opacity usually originates through hardening of glass matrix by adding high amounts of zirconia containing frits into the glaze batch [2]. Nowadays, researches point out that certain type of glass-ceramic layers can be alternatively employed as tile coatings lowering the use of zirconia containing expensive opaque frits. A rather high crystallization capacity of glass- ceramic glazes due to zirconia presence in glass network makes them suitable candidate as a glaze coating with a desirable micro-structure. One of the best methods to obtain an opaque glaze surface is to induce a crystal phase in the coating, whose refractive index differs significantly from that of the glassy matrix. The opacity of such coating is determined by the diffusion, refraction and reflection of light through the layer containing emerging crystals, and the degree of opacity mainly depends on the size and quantity of crystals. The development of glazes not consisting of expensive or toxic components is of special interest [3]."

Jan 1, 2008

By Kathleen M. PH. D. Kowalski

This paper discusses human judgment and decision-making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision-making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behavior in underground mine fires. The authors assert that stress is one of the factors that decision-makers must contend with in most life-or-death situations. They suggest that a better understanding of individual's judgment and decision-making activities while under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers, and policymakers.

Jan 1, 2008

By J-H Shin, Y-S Jung, D-J Youn, G-J Bae

This research is to grope for a method to reduce high pore pressure taking place on tunnel shotcrete lining, especially in underwater tunnels, effectively by utilising a new concept of patternised pin drain. Accordingly, the patternised pin drain system is investigated numerically in order to confirm to the effect of reduction of pore pressure by the pin drain and its effective application. Installation of pin drain shows considerable reduction in the figure of pore pressure. It is found through 2D numerical modelling that the change of pore pressure, according to the shape and the location of pin drain, is sensitive by the sequences of the change of location > the change of length > the change of angle degree. In the results of investigation in 3D modelling, the pore pressure is the largest in the centre of the interval among pin drains, and it is possible to obtain an ideal degree of longitudinal angle and an interval by investigating pore pressure taking place on the lining.

Jan 1, 2008

By G Gibson

Realising that current roadway development performance levels were unlikely to sustain new generation high-capacity (15 Mt/a) longwall mines then being planned, the Australian Coal Association Research Program (ACARP) established a Roadway Development Task Group (RDTG) in 2005 to develop a research strategy targeted at improving roadway development performance in Australian longwall mines. The initial phase of the project identified a number of factors that differentiated best practice mines from others, and proposed a multi-faceted research strategy encompassing both short- and long-term research initiatives, including:conducting regular benchmarking studies across the industry to identify factors contributing to improved performance and to monitor performance trends,conducting regular industry roadway development operatorsÆ workshops to facilitate the transfer of successful roadway development improvement initiatives throughout the industry and facilitate networking between development practitioners,development of alternative skin reinforcement and containment measures that would eliminate the use of steel mesh and enable face support systems to be fully automated,development of automated bolting and mesh handling systems that would enable operators to be removed from the immediate face area,development of a body of knowledge of industry roadway development practice,development of a web-based information management system to capture and transfer emerging developments in roadway development practice and technology,reviewing the Australian civil tunnelling and underground metalliferous mining sectors to identify practices and technologies that could potentially be utilised to improve roadway development performance, anddeveloping a new generation high-capacity mining system capable of +10 metres per operating hour for 20 or more hours per day (CM2010). The paper reports on the progress of the above initiatives and outlines strategies to continue the pursuit for improved roadway development performance.

Jan 1, 2008

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By S Meffre, S Golding, K Zaw, J McPhie, R James, S Suphananthi

The Chatree deposit is located in the central portion of Loei Fold Belt, which extends from Lao PDR in the north through centralThailand to Cambodia in the south. Epithermal gold-silver mineralisation at Chatree occurs as veins/veinlets and stockworks with minor breccia in volcaniclastic and volcano-sedimentary rocks of andesitic to basaltic andesite composition and Permo-Triassic age. This preliminary oxygen isotope study mainly focuses on vein quartz of Au-Ag bearing mineralization (Stage 2) and a few samples of late Stage 4 quartz ¦ calcite veins. Quartz from Au-Ag bearing mineralisation has oxygen isotope values ranging from 8.1 to 12.3ë with the lowest values generally occurring at the deeper level (140 m below the surface). The late barren quartz ¦ calcite veins (Stage 4) tend to have higher oxygen isotope values ranging from 11.9 to 12.0ë. The oxygen isotope composition of the Chatree ore fluids were calculated at 250¦C, 300¦C and 350¦C based on homogenisation temperatures of fluid inclusions. The calculated oxygen isotopic composition of the Chatree ore fluid ranges between -1 and 6ë that overlaps with both meteoric and magmatic compositions. This shift in oxygen isotope compositions may relate to processes such as water rock-interaction and/or mixing of meteoric and magmatic fluids. It is interesting to note that the lowest quartz oxygen isotope values are spatially more or less confined to the prominent structures in the centre of the major ore zones. These structures may have been acted as conduits for higher temperature magmatic fluids. The quartz oxygen isotope values increase outwards from the centre of the main ore zones to the margin of the pits possibly due to mixing of magmatic fluids with lower temperature meteoric water. Whole rock oxygen and hydrogen isotope studies are in progress to investigate isotopic trends in the wall rock away from the ore zone. The systematic variation of oxygen isotopes in quartz from the mineralised veins and adjacent wall rocks could potentially be used as a vector to ore. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Max Gwynn, Tony Suckling

"The new Wembley Stadium is the most spectacular soccer stadium in the world, built to the highest specifications, using the latest technology and offering visitors an unrivalled match-day experience. Wembley Stadium is the home of English soccer, dating back to 1918 when the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Empire Stadium, as it was originally known, was completed in 1924 in just 300 days and cost £750,000 ($1.4m). It was finally closed in 2000.The new Wembley Stadium, which opened in 2006, features fully covered seats for 90,000 fans and a striking arch that sits above the northern half of the stadium. With a span of 315 m (1040 ft), the 133-m (440-ft) tall arch is the longest single-span roof structure in the world. It supports the entire weight of the northern roof and 60% of the weight of the southern retractable roof. This means there is no need for columns within the stadium and ensures unobstructed views.Multiplex Constructions (UK) Ltd. employed Stent Foundations Limited to construct the £10m ($19m) foundations package for the new stadium. The scope of works for the foundation package included the design and construction of all foundations, including all main works piling, temporary works piles for the arch and roof, and tower crane piles. The scope also included trial piling and pile testing, setting out and removal of spoil.Piles were constructed by using bored cast-in-place techniques with both hydraulic and traditional crane-mounted rigs. Stent also installed sheet-piled walls at three locations to the site’s northern boundary. In addition to the main contract works, Stent constructed a £2m ($3.8m) contiguous bored-pile retaining wall within the demolition and earthworks package (Figure 1). This work was carried out as a subcontractor to Griffith McGee."

Jan 1, 2008

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By S. K. Kawatra

"A typical steelmaking facility produced 50,000 tons per year of slag in their hot-metal desulfurization process. This slag had a sufficiently high iron content that it could be beneficiated and recycled in a blast furnace, provided that the slag could be agglomerated into pellets suitable for use as blast furnace feed. In this work, beneficiated slag was agglomerated using both a conventional bentonite binder, and a fly-ash-based binder (FBB) that was formulated by the investigators. The FBB consisted of a combination of highcarbon fly ash with calcium hydroxide activator, allowing the FBB to exhibit binding properties when moistened. It was determined that beneficiated slag agglomerated with FBB had superior compressive strengths compared to slag agglomerated with conventional bentonite binder. The FBB is therefore a satisfactory method of binding the agglomerated slag. Since the fly-ash component of the FBB is commonly discarded as waste, this approach also provides a means for utilizing high-carbon fly-ashes that currently have very little commercial value.IntroductionIn 2006 approximately 72.4 million short tons of fly-ash were produce in the United States [1]. The majority of fly-ash which was used that year was consumed concrete, structural fills, and cement. It is also used in road base, aggregate, and other applications. However, 55.2% of the fly-ash produced in 2006 was not utilized and ended up being sent to a landfill. Essentially all of the land filled fly-ash could be a suitable binder for pelletizing desulfurization slag and other steel plant waste oxide materials. Fly-ash based binders (FBB) have been shown in laboratory studies to be suitable for producing iron ore concentrate pellets of equivalent strengths as those bonded with bentonite [2,3,4]. The utilization of highcarbon fly-ash within the market is important for reducing the volume of currently unmarketable and land filled fly-ashes. FBB would be a much cheaper alternative to the current bentonite binder or organic binders used for iron ore concentrate and would help to reduce pellet costs. Currently, transportation more than doubles the final cost of bentonite since it is produced hundreds of miles from the pelletizing plants, while fly-ash is produced from power plants located nearby pellet plants and steel mills. FBB’s also show promise for use in other high volume applications such as foundry sand mold binders."

Jan 1, 2008

By P G. Gaylard

P754 has been an unusual project in that its main aim was to develop a code of practice for metal accounting with the following key objectives:Development leading to an agreed industry standard at corporate governance level Significant improvement of the credibility of metal accounting from deposit to saleable product Development of guidelines for data collection, data analysis, reporting and audit A data analysis toolbox which provides go/no go testing for metal balance data Promotion of industry adoption of these guidelines to improve transparency and financial credibility. Over time, these guidelines may evolve into a code and eventually into a standard Develop and train engineers to become expert in metal balancing and reporting. Papers like this one and the workshop which follows this conference are part of promoting the code for adoption by industry. Developing a code of practice has traditionally been the provenance of professional bodies associated with particular industries û often on a voluntary basis. Given todayÆs industry pressures, it was felt that funding key input might accelerate the development process as well as offer opportunities to research some of the problems and to train some post graduate students in a difficult discipline. In fact, the project has brought together six industry sponsors from a wide range of process types, three research providers, and funded students in South Africa and Australia. The project has also attracted input from the financial community. A textbook to support the application of the code has also been written. The industry sponsors have made the Code and Guidelines available on request to help to facilitate its use by the mineral industry beyond the sponsor group. The Code and Guidelines have already been translated into Spanish and Portuguese which suggests that industry acceptance may happen quite quickly. The main thrust of the code is to integrate commercial and technical performance to a much higher degree. The Check in-Check out (CI-CO) method has been chosen as the vehicle for this combined approach. The mass and metal values used for CI-CO are 'absolute' and provide the basis of financial transfers. The CI-CO process occurs at each transfer of custody - whether between divisions within a company, or between companies. This approach means that measurement of mass and metal flows becomes the critical element of the process and that a quantitative knowledge of measurement accuracy and precision is also essential. This knowledge allows technical differentiation between differences which are within the expected margin of variation and those which must be formally identified as discrepancies and subject to a process of investigation and sign off. Hence, the application of the code for most companies should be more evolutionary than revolutionary, but with substantially more emphasis on measurement and definition of measurement error. Where this can be achieved, it should bring the mineral industry more into line with other industries competing for investment funds, community acceptance and future employees.

Jan 1, 2008

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008