Search Documents

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

Traditional methods for calibrating the most customisable forms of GyÆs formula for the prediction of sampling variances involve a large amount of experimental work. This work is often extremely sensitive to outlier treatment and often relies on assumptions. A general methodology called æthe consistency methodÆ, however, has proven efficient in guiding these critical steps and adding objectivity to these subjective tasks. After a quick exposition of its principle, it is shown how it can also be used to reduce the amount of experimental work when dictated by budgets.

Jan 1, 2008

By Christopher Blazek

Presentation Overview ?2005 Train Derailments ?BNSF Investigation and Remediation ?BNSF Test Program ?Test Results ?BNSF Dust Control Goals ?National Coal Transportation Study ?Comparison of Different Topper Agents ?What Constitutes a Topper Program

Jan 1, 2008

By S Furman, M Caccetta, A Hacket, B McDonald, M A. Wells, D Lau

In 2004, the Western Australian Department of Industry and ResourcesÆ Burrup Rock Art Management Committee commissioned a number of independent scientific studies to evaluate the condition of rock art in the Burrup Peninsula near Karratha (Western Australia). These studies are evaluating the physico-chemical aspects of the effect of environmental modification on the visible appearance of the rock art. Because of the cultural significance of the sites, the research approach has been to employ non-destructive testing strategies and work in the field has progressed with respect for the importance of the area. This paper only reports the spectral mineralogy monitoring at each of the sites to evaluate whether changes in mineralogy are observed on rock surfaces. Reflectance spectroscopy is a non-destructive, in situ materials characterisation technique that provides information about the mineralogy. The minerals detected include haematite, kaolinite, chlorite, goethite, gibbsite and manganese oxides. Current results indicate that the surface mineralogy of the rock art has not changed in the last four years.

Jan 1, 2008

By Z. T. Bieniawski

Geomechanics signifies the science and engineering of soil and rock materials and of rock masses. It is a field of professional practice and research that draws heavily on the elements of soil and rock mechanics. Geomechanics contributes to a number of disciplines: mining engineering, civil engineering, geological engineering, petroleum and natural gas engineering, and engineering geology (including the elements of geohydrology and geophysics). These disciplines are involved in the design and construction of such projects as mines, tunnels, foundations for structures, excavated rock slopes, dams, shafts, boreholes, oil reservoir wells, underground storage facilities for oil and gas, and hazardous waste repositories. Geomechanics allows us to improve both our environment and our quality of life. In the context of this Handbook, the scope of geomechanics is discussed mainly from the point of view of applications to mining engineering. However, the coverage of the subject mate¬rial is so comprehensive that it is relevant to other disciplines as well. Section 10 covers the field of geomechanics in a structured fashion, beginning with the fundamental principles and leading into practical applications in mining engineering. Throughout the treatment of the subject, knowledge of geologic conditions is assumed since this is discussed in other sections of the Handbook. An important feature of this section is a series of practical examples illustrating the various aspects of geomechanics. Since geomechanics is concerned with both soil and rock mechanics, Chapter 10.1 introduces the fundamentals of soil

Jan 1, 2008

The type of population encountered in the sampling of coal, ores and other products of natural phenomena is one in which the variance within a cluster of elements generally increases steadily as the size of the cluster increases. To enable estimation of variances of stratified random or systematic sampling for such populations one must model the serial correlation function or alternatively, the variogram function. The author has postulated a specific symmetry of the serial correlation function which leads to expressions with rich theoretical and practical implications. These expressions provide a spatial correlation function which explains power law relationships often observed in studies of dispersion variances. They also enable straightforward calculations of sampling variances. The importance of the role of finite population size in the equations leads one to examine previously held concepts of ælargeÆ and æsmallÆ sample populations. The model based on the symmetry postulate is a fractal model with the serial correlation function of a hypothetically infinite population being of the same form as that developed by Mandelbrot for discrete fractional noise. Techniques used in fractal mathematics apply, including box counting and fitting of a dimension function. The paper establishes a framework for the understanding of this fractal theory and demonstrates how to calculate sampling variances from the model variogram using simulated data fitting the model.

Jan 1, 2008

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By R T. A MacGillivray, S B. Curtis

Bacteriophage (phage) are viruses that infect bacteria. Protein coatings on the surface of the phage particle can be genetically engineered so that they bind to inorganic molecules. The filamentous phage particle is about 930 nanometres in length and 6.5 nanometres in diameter and consists of a single-stranded molecule of DNA surrounded by five different coat protein molecules denoted P3, P6, P7, P8 and P9. Peptide sequences in the P3 coat protein that bind to sphalerite and chalcopyrite have been identified. The binding is selective; phage with specific P3 peptide sequences bind to minerals but do not bind to silica or to pyrite. Two peptide sequences in the P8 coat protein that bind selectively to chalcopyrite and pyrite have also been identified. The amino acids in the P8 binding sequences are hydrophilic and thus a coating of a mineral particle with phage having these peptide sequences may render the particle hydrophilic. Experiments are underway to confirm this. Phage are relatively easy to grow and are not living organisms requiring an energy source to maintain life. Phage can also tolerate a range of pH and temperatures. Given this, and the ability to indentify phage coat proteins that bind selectively to a variety of inorganic molecules, phage have the potential to be useful tools in mineral processing and waste treatment.

Jan 1, 2008

Mid-ocean ridges host approximately 65 per cent of about 100 known sites of high-temperature venting and polymetallic sulfide deposits; most of them are located at the East Pacific Rise (EPR), while more diverse mineralisation styles occur at the Mid-Atlantic Rise (MAR). Seafloor hydrothermal activity at the EPR are related to MORB while different substrates, including MORB and ultramafic intrusive rocks, are associated with æblack smokersÆ at the MAR. Depth of hydrothermal activity ranges from 0.7 to 4.3 km. High-temperature vents precipitating Cu-Fe sulfides (chalcopyrite and isocubanite, rare bornite), pyrrhotite, pyrite (¦ marcasite), and sphalerite, and low-temperature edifices precipitating marcasite (with pyrite), sphalerite, barite, andsubordinate chalcopyrite (pyrrhotite and isocubanite are absent) occur in both environments. There are considerable differences in Fe, Zn, Cu, Ag, Au and trace element contents in ores and in theFeS contents in Zn-sulfides in these deposits. Acomparison with anhydrite and sulfide minerals precipitating from modern black smoker fluids sulfide reveals many similarities but also some important differences. Fluids with salinity values above and below that of seawater at 400¦C down to 130 - 170¦C deposited sulfide minerals. Mantle-derived He prevails in fluids trapped by sulfides in EPR 9¦N and 21¦N hydrothermal systems. Hydrothermal fluids in MAR and back-arc systems are richer in radiogenic 4He. The sulfur isotope composition varies in the different hydrothermal fields and within zones of a chimney. EPR sulfides display narrower range of d34S values, while MAR and back-arc sulfides can bedepleted and enriched in the heavier d34S isotope. The most important finding is that fluid temperature, salinity, R/Ra ratios and d34S values ranged more significantly in the polymetallic sulfide deposits than when measured directly on venting fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008

By K-S Kim, C-Y Kim, D-G Kim

In tunnel construction or other underground construction, a detailed knowledge of the rock mass ahead of the face is essential for both safety and efficiency of work. Many tunnel collapses have been reported to occur because of lack of appropriate information, such as the geological conditions ahead of the tunnel face. One of the methods which can identify rock mass conditions is the application of drill monitoring data obtained from blasting drill holes, which can detect abrupt and unexpected changes in ground conditions, geological structure and the mechanical and physical properties of rock mass. This paper presents a new approach to how drill performance parameters can be used for prediction of geological conditions ahead of tunnel face. The predictions are based on monitoring the drill parameters of instantaneous advance speed, torque and tool pressure. In order to assess conditions ahead of tunnel face, tunnel seismic profiling (TSP) and a horizontal boring investigation were undertaken and the obtained data compared to the drilling data. The predicted results using drilling performance parameters correlated well with geological conditions ahead of tunnel face.

Jan 1, 2008

In 2006, a total of 4,573 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 30.7% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,042; 44.7%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=368; 8.0%), followed by Texas (n=342; 7.5%).

Jan 1, 2008

A new national-scale geochemical survey is under way inAustralia with the aim to provide energy and mineral explorers with state-of-the-art precompetitive data and information about the continentÆs potential resources. This low-density geochemical survey will provide a national geochemical data layer using consistent sampling medium and sampling, preparation and analytical methods. Large-scale geochemical patterns thus revealed are expected to point to new areas of exploration potential. The project is funded under the Onshore Energy Security Program. It is hoped that this new national geoscience dataset will help make Australia a more attractive destination for energy and mineral exploration investments. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Rostami, D Tadic

While hard rock tunnel boring machines (TBMs) have an established track record in the tunnelling industry, accurate estimation of TBM performance for each specific project remains critical. Machine performance prediction is required to assist planning activities, including costing and schedule preparation, machine specification and effective planning of maintenance and repairs. In addition, monitoring machine performance during the construction period is required to assess and manage excavation progress, and to achieve optimal advance rates based on specific geotechnical conditions exposed during excavation. TBM performance analysis can also contribute to the development of more accurate performance prediction models for future applications. Rock mass characteristics play a dominant role in machine performance. This paper offers a review of the impact of rock mass characteristics on TBM penetration rates for two specific tunnelling projects. A discussion is provided on the results of statistical analysis of available field data, including geological back mapping, rock properties and measured rates of penetration (ROP). The analysis offers a comparison of the achieved and predicted ROPs to provide a better understanding of the influence of rock mass properties on the performance of hard rock TBMs. A new rock mass adjustment factor is introduced to enhance the accuracy of an existing prognosis model for use in jointed rock masses.

Jan 1, 2008

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

By J F. C L Costa, J C. Koppe

The goal of this study is to characterise co-processed clinkers by identifying the most common minor elements, their distribution in the clinkers and possible effects on the mineralogical properties of the same. The results show the presence of an elevated content of transition metals, especially manganese concentrated in the matrix (up to three per cent) of the clinkers. Anomalous concentrations of arsenic have also been detected, especially at silicate crystal edges. The results indicate that the tracer elements can perfectly be associated to the mineralogical characteristics of the clinkers.

Jan 1, 2008

By M. L. Baharani

Looking for an idyllic paradise that has investment and business potential as spectacular as the stunning views of mountains, the rich Ganesh Himal zinc-lead deposit exposed between 4,050 m and 5,000 m is the answer. Arising from the sea floor in a span of 55 million years, the enchanting Himalayas had remained one of the most potent factors influencing the Asian region. The challenges of the mighty Himalayas notwithstanding, it continues to provide opportunities for the humankind in optimum usage of the natural resources and sustainable development. Optimal management of natural resources in mountain areas through decision support tools offered by remote sensing will go a long way in realization of the Ganesh Himal Zinc-Lead Project. The authors have a real life endeavor spanning over 37 years in developing a mining industry in a mountainous region of Nepal and an attempt to integrate with the development of other natural attributes of the region. With rapid acceleration of science and technology, humankind has acquired power to transform his environment countless ways and on an unprecedented scale. While mineral resources are the pillars on which we have built industry and infrastructure, industrial countries in the North have been in the forefront of technological advancements, the developed countries of the South have been at the receiving end of exploitation of mineral resources worldwide. A relationship with natural environment, re-crafted by the civilizing impulse, to meet human demands are upcoming challenges for management of natural resource in sustainable manner for a livable world.

Jan 1, 2008

By John Brulia

It has been said that the only thing that remains constant is change. After more than 33 years in the explosives industry, I do not take any exception to that adage. I have seen changes in people, changes in ownership of companies-both small and large, domestic and international; changes in products; changes in the way we use products; changes in the way we handle products; changes in regulations; and last, but not least, changes in our perceptions of threats to our industry.

Jan 1, 2008

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008