Search Documents

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

Researchers with the National Institute for Occupational Safety and Health (NIOSH) have developed a training module to educate both new, inexperienced miners as well as veterans on important issues related to self-rescue and escape procedures. These include: (1) physical and environmental conditions that can be encountered in a mine after a major explosion, (2) knowledge of emergency meeting locations and escape routes, (3) the importance of using self-rescuers, even in seemingly clear air, to keep the lungs isolated from contaminants, and (4) why miners should not go off to look for others who are missing. In addition, the module may stimulate miners to think about and discuss mine explosions and the devastating effects of such an event.

May 1, 2009

By CIM CIM

Why Workplace Important! ?We need Diversity is to do more in the industry as a whole to encourage and support diversity. It has long been an industry of white dudes and we?re not going to survive if that?s how we continue to think.? ? Mark Scott, HR Superintendent, Vale Inco PURPOSE OF MINING FOR DIVERSITY ? Share best practices in the areas of HR Development ? Support industry in attracting, recruiting and retaining a diverse workforce ? Raise awareness of industry HR challenges and collaborate with stakeholders to develop sustainable HR practices

May 1, 2009

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Feb 1, 2009

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By P. A. Roberts

A modified in situ leaching method for extracting gold from oxidized gold ores using a non cyanide lixiviant is proposed. A non cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide bearing solutions into the subsurface. Oxidized gold ores are the initial focus because earlier research on the use of sodium thiosulphate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulphate breakdown. A reconnaissance research programme, involving ore characterization and hydrometallurgical testwork on samples from four Australian ore deposits and preliminary reactive transport modelling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulphate and ferric EDTA, and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples under anaerobic conditions. The ore characterization and reactive transport studies, suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Physical permeability enhancement could be achieved by blasting and/or hydraulic fracturing of the ore. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in place leaching? has been adopted for the proposed gold extraction system

Jan 1, 2009

By Daniel P. Lathrop, Leslie C. Taylor, William L. Fourney

Except when the target is on the surface, e.g. a tank track, the most important loading mechanism from a buried charge on a target above it is the impact of soil propelled at the target by the expanding gas from the explosion. Detonation of a shallow buried explosive generally yields an unstable interface between the rising soil and the air which appears to be the result of Richtmyer-Meshkov instability. Irregular “fingers” of saturated sand extend into the air above a more generalized dome of soil. These fingers move at a much higher velocity than the material between them at smaller stand off distances. As a result, the local load on the target at positions on the target at the same distance from the charge may vary by 50% or more from shot to shot or even within a single shot. This variation requires a large design safety factor to assure the integrity of design of mine-resistant vehicles.

Jan 1, 2009

By Ronald D. Boyer

"Early in the design stage of Meadowlands Xanadu, the client’s project director informed me that “after construction, nobody is going to come to Xanadu to see the foundations.” My response was, “Well, that’s good, because the only reason someone would come to see the foundations is if there is a problem with them.” The client’s real message was clear: the money for the project would be better spent on architectural design components and interior finishes that would attract high-end tenants and entertainment seekers. The foundations, however, were challenging. The sheer size of the Xanadu development, the varying depths to rock, the loading conditions associated with the different structures, and the construction sequencing required the use of multiple deep foundation types and specialty foundation contractors. Xanadu, when completed, will consist of over 2.5 million sq ft of entertainment venues, restaurants and retail stores; America’s first i n d o o r s n o w dome; North America’s tallest (287 ft high) Ferris wheel; and four parking decks. Finished grades for Xanadu were essentially within about 1 to 2 ft of existing grades at the site, except for a 5 acre wetlands area, which received about 8 ft of new fill. Before the current construction, the approximate 75-acre Xanadu site was occupied by the Continental Airlines (now Izod) Arena, on-grade parking lots and the wetlands area. The Arena property is part of the New Jersey Sports and Exposition Authority (NJSEA) Meadowlands Sports Complex, which also includes Giants Stadium and the Racetrack, and is located in East Rutherford, N. J. Subsurface ConditionsThe site subsurface conditions include fill materials underlain by organic silt and peat (former marsh deposits or “meadowmat”), varved clay, glacial till and shale bedrock. The Xanadu site had been a marsh until the Sports Complex was created by filling in the early 1970s. The fill consists of dredged materials from Lower New York Harbor imported by hydraulic pipeline from the Hudson River. The fill also includes “historic fill,” defined as nonindigenous material deposited to raise the topographic elevation of a site, such as construction debris and other nonhazardous solid waste, and was generally encountered in thicknesses ranging from 8 ft to 18 ft. Within the previously developed portion of the site, a layer of marsh deposits consisting of peat and organic silt was encountered beneath the fill in thicknesses ranging from two ft to seven ft. Within the existing wetlands area, the marsh deposits were up to 10 ft below existing grade. The varved clay stratum was six ft to 36 ft thick. The depth to shale rock increases from approximately 15 ft near the west side of the site to approximately 80 ft near the south side. Groundwater was tidally influenced and varied from about 6 to 12 feet below both existing and proposed grade."

Jan 1, 2009

By M Scoble

This paper is based upon the experiences of collaborating academics in two mining schools and their personal view of attempts to integrate the principles of sustainable development into mining education and research. In this quest, the concept of sustainable mining practices is proposed, not only relating to environmental, social and economic performance but also stressing mine safety and efficiency. These practices need to support strategies that enable flexibility and resilience within mine operations to counter recessionary cycles. Also, these counter-cyclical strategies are now imperative for sustaining mining education and research itself. There is a critical interdependence between these two different perspectives on æsustainabilityÆ. The paper concludes by demonstrating models of strategies that promote inter-disciplinarity, collaboration and networking for sustaining mining schools.

Jan 1, 2009

Oceana Gold CorporationÆs (OGC) Frasers underground (FRUG) transitioned into production in early 2008. The mine uses a relatively unique yielding pillars mining method that takes its lessons from empirical coal mining practices more so than hard rock techniques. Being a low-grade, flat-dipping resource hosted in the highly structured relatively weak Otago schist in central South Island in New Zealand, meant a number of iterations were undertaken to find the right mix of mining cost and resource extraction. Mining is on the down dip extension of the active Frasers open pit at the Macraes site (that extracts the full shear zone package at a head grade of 1.5 g/t). The challenges for the FRUG feasibility study team was to deliver an net present value (NPV) positive operation that would exist as a coproduct with OGCÆs other New Zealand operations, allowing it to make use of the high throughput low cost refractory ore treatment facility.Key factors in the successful project design were: Net capital costs kept to less than NZ$30 M by realising significant gold revenues from mine development from month four onwards. Virtually eliminating waste development by putting all key capital infrastructure in the low-grade ore adjacent to panels and maintaining the option of extracting this resource on retreat from the mine. Targeting a specific higher grade halo ore package within the entire mineralised shear zone. Applying a mining method that accepted a higher degree of dilution, ore loss and resource loss (in yielding and non-yielding pillars) to the flat-dipping resource. Thus providing an acceptable margin per tonne and resource tonnes mix, as the resource could not support a conventional low-cost caving operation, nor a higher cost room and pillar or open stope and backfill operation. 2008 has seen increasing tonnes and grade performance with a corresponding decrease in cost per tonne and cost per ounce as the mine has reached nominal capacity and is producing an operating surplus. The challenge will be to maintain and improve.

Jan 1, 2009

By Arsenio Enriquez, Adrian Deneys

"Rio Tinto through its subsidiary Kennecott Utah Copper Corporation (KUC) and Praxair have implemented the CoJet® gas injection system for copper anode refining. The system provides the capability to melt on average 60 to 70 tons of scrap copper per heat (with acceptable NOx emissions). The system has demonstrated the potential for tuyere-less sulfur and oxygen removal using coherent jet technology.This paper describes the process concept, system development, laboratory testing, implementation, current operation and ongoing developments."

Jan 1, 2009

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By M A. Lund, C D. McCullough

In Australia and worldwide, open cut mining has become increasingly common over the last few decades through changes in excavation technology and ore economics. However, such operations frequently leave a legacy of open mine pits once mining ceases. Pit lakes will then form in mine pits that extend below the water table when dewatering operations cease. Pit lake waters are typically contaminated with metals, metalloids, saline or acidic/alkaline and rarely approach natural water body chemistry. Physically, pit lakes have unique bathymetries, are often strongly wind sheltered and have very small catchments. Nevertheless, pit lake waters often constitute a vast resource but of limited beneficial use (due to water quality issues); with a potential to contaminate regional surface and ground water resources. Water in pit lakes has the potential to be useful for a range of purposes in the Australian context of characteristic hot, dry climate and relatively few natural water bodies. Consequently, pit lakes can be seen to represent either a significant liability or a water resource to mining companies and regional communities. However, the lack of knowledge on pit lakes continues to hinder their proper management. This paper summarises the limited information currently available on water quality associated with Australian pit lakes. Information on pit lake occurrence, distribution and water quantity and quality is not nationally collated and requires immediate and ongoing attention from both mining companies and regulating authorities. Lack of a readily available database for pit lake occurrence, distribution and water quality fails to realise the potential for these water resources by both mining companies and Australian communities. Lack of access to pit lake quantity and water quality data may also lead to failure to manage this significant source of mining environmental risk.

Jan 1, 2009

By G A. Blengini, S V. èolar

The minerals industry is faced with choices beginning in the exploration phase and extending over the life cycle of the mine. Firms examine the technical feasibility of alternative actions and typically rank them based on economic performance. Increasingly firms also consider alternativesÆ contribution to sustainable development. There are many visions of what a sustainable future should look like and much debate about what should be sustained. Sustainability is a process, a series of incremental actions, and each alternative course of action has the potential to further progress toward one or more sustainability goal. However, because it is not possible to sustain everything everywhere simultaneously, trade-offs and choices inevitably have to be made.Sustainable decision making before investment (ex ante decisions) should incorporate a broad suite of quantitative and qualitative information. One approach is to utilise an integrated sustainability assessment (ISA) framework that supplements traditional technical and financial tools with other tools such as objectives hierarchies (OH) and life cycle assessments (LCA). OH is a problem framing method that captures stakeholder and decision maker interests, objectives and values. LCA addresses material and energy flows, and environmental impacts. The outputs of these tools can be combined with additional qualitative measures and analysed using multi-criteria decision analysis (MCDA). MCDA models facilitate comparison of different alternatives on the basis of a set of criteria and indicators. Some can incorporate information on risk attitudes and preferences ( multi-attitribute value theory models) and others uncertainty about outcomes (multi-attribute utility models). Studies have been published describing and comparing tools for minerals sector decision analysis. Our paper extends this literature, discussing how a combined OH-LCA-MCDA can support ex ante sustainability assessment by incorporating preferences, risk attitudes, and monetised or non-monetised social and economic variables, in a manner that captures their inherent complexity. We also discuss how such a combined model would support trade-off analysis.

Jan 1, 2009

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009

By Markus A. Reuter, Jacob Wood, Robert Matusewicz

Over the last 20 years, significant improvements in copper smelter productivity have been realized through the advent of continuous smelting processes. This progress has until recently however, not been carried through to copper converting. Peirce-Smith converting has been widely used by the copper industry for 100 years but is limited by its batch nature in achieving large scale of production. A logical next step is therefore copper converting on a continuous basis with its inherent environmental benefits. A number of continuous converting technologies are currently in use or being developed within the copper industry, the majority of these operating with calcium-ferrite slags. A notable exception however is the Ausmelt Continuous Copper Converting (C3) technology which has focused on operation with ferrous-calciumsilicate or loosely called olivine type slags. This paper discusses the merits of the Ausmelt C3 process and the advantages offered in terms of operational flexibility and process control arising from the use of lime modified iron silicate slags. It also examines the effects of key process variables pertinent to continuous copper converting from both a theoretical and experimental/operational perspective.

Jan 1, 2009

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009