Search Documents

By Denis Rickman, Jon Windham, Stephen Akers, Byron Armstrong

The soil crater formed by detonation of an explosive charge is of considerable military interest because of the common use of explosives to create soil obstacles. The soil crater is also an important piece of forensic evidence for the investigation of terrorist bombings. With recent advances in numerical codes, modeling and simulation of explosively-formed soil craters is becoming an attractive means of analyzing this phenomenon. Consequently, the need exists to better understand the relationship between soil properties and the resultant soil crater. An extensive database has been developed for the case of explosives detonated in or above in-situ soils of various types. However, in most cases, the soil properties were either not adequately quantified or the soil materials themselves varied such that the gross properties were poorly understood. A research program is underway to improve methods of relating soil crater dimensions to soil identification properties such as USCS classification, particle-size distributions, and Atterberg limits, as well as to soil composition properties such as density, moisture content, and volumes of solids, water, and air. As part of this effort, both explosive detonations conducted over well-controlled and well-documented soil backfills and companion numerical simulations were studied. This paper presents an overview of the effort.

Jan 1, 2010

By W. G. Pariseau

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mine in the Coeur d'Alene Mining District of northern Idaho. The present study uses rock deformation measurements to validate and calibrate a geomechanical model of the experimental Lucky Friday underhand longwall (LFUL) stope on the 5,100-ft level of the Lucky Friday Mine, Mullan, ID. The calibrated three-dimensional, finite-element model and measurements of rock mass displacement show a correlation of 0.795. The calibration reduces rock mass modulus to 14 to 17 pet of laboratory values and rock mass strength (with an energy rule) to 37 to 41 pet of laboratory values. This model suggested that stress-related ground control problems would be encountered west of the stope where the vein makes a right-angle turn and then splits. Rock burst activity was concentrated in this area during mining of the LFUL stope.

Jan 1, 2010

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By X. M. Wu

The paper describes four different types of support for deep excavations, which are currently used in China. Local experiences were illustrated by presenting case histories for each type of support. For braced excavation in soft clays in Shanghai, the earth pressure against bracings were found to be in conformity with the trapizoidal estimation given by Terzaghi and Peck (1967). For tie-back support of excavations in Beijing and Shengyang, earth pressures were found to be much less than those predicted by ordinary rules. In the construction of a mining shaft in coarse sand below ground water level, high pressure jet grouting has been successfully used to form a circular impervious lining of the shaft. As an effective anti-slide measure, large diameter reinforced concrete piles constructed by open shaft method have been widely used with success.

Jan 1, 2010

By Huimin Lu, Min Li, Jinghua Zou

"Zeolitic imidazolate frameworks (ZIFs) are new type of porous materials, form inerratic polyhedral in three-dimensional with large cages and small apertures, and appear structural diversity. Their hole size can be adjusted. These materials have high selective adsorption capacity to carbon dioxide. In this paper, zeolitic imidazolate frameworks were synthesized by solvothermal synthesis method with dimethylformamide (DMF) as solvent and structuredirecting agent, divalent metallic ions as cation, and imidazole as ligand. The crystals were characterized with XRD, SEM for their crystal structures and physical properties, the adsorption of the crystals for carbon dioxide was also tested, and the result suggests that these porous materials have a capacity of 1.35ml/g for storing carbon dioxide at 273 Kelvin under ambient pressure.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the main environment problems, contemporary research has focused on ways to slow or stop this trend. CO2 capture has attracted attention due to the potential to trap and sequester large amounts of CO2 from concentrated sources such as power plants [1]. Traditional technologies in capturing CO2 include absorption by aqueous amines [2]. However, utilization of this process is energy intensive and expensive. Carbon dioxide storage materials investigated so far can be divided into two categories: chemical storage adsorbents and physical storage media [3]. The first kind of materials can chemically adsorb carbon dioxide within their structures and need thermal energy to release the adsorbed carbon dioxide. The examples of the chemical adsorbents include aqueous amines, gas-hyperbranched aminosilicas [4]. The physical adsorbents store carbon dioxide by physical adsorption of carbon dioxide at elevated pressure and release the adsorbed carbon dioxide at low pressure. The physical adsorbents that have been investigated for carbon dioxide storage include zeolites, carbonaceous materials and other porous materials. Until recently, a new type of microporous material, known as zeolitic imidazolate frameworks (ZIFs), has been reported as promising adsorbents for carbon dioxide storage [5 ~ 10]."

Jan 1, 2010

By Qingwei Wang

Heavy metal-containing wastewater from hydrometallurgical processes of lead-zinc was treated by biologics in a 200 m3/h industrial scale experiment. The result shows that Zn concentration declined from 50.28 mg/L~240.81 mg/L to 0.21 mg/L~1.98 mg/L, Pb from 1.00 mg/L~13.47 mg/L to 0.083 mg/L~0.71 mg/L, Cu from 0.24 mg/L~2.38 mg/L to 0.059 mg/L~0.40 mg/L, Cd from 2.12 mg/L~23.47 mg/L to 0.011 mg/L~0.071 mg/L and As from 0.50 mg/L~6.00 mg/L to 0.005 mg/L~0.10 mg/L. The concentrations of the above heavy metals in the treated water were lower than that in Integrated Wastewater Discharge Standard (GB8978~1996) in China. Furthermore, the treated wastewater was recycled and reused in smelter plant. Zinc content in hydrolytic sludge reached up to 34.04%, which indicates that this sludge can be used to recover valuable metals.

Jan 1, 2010

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines collected and analyzed overcore measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 2010

By A. G. Belova

With the federal climate change legislation in progress, there is a need for demonstration-stage technologies aimed at providing clean energy from coal. Our research aims to experimentally illustrate the feasibility of capturing CO2 on a novel sorbent system from a gaseous stream. The gas is then released resulting in a regenerated sorbent and a pressurized stream of pure CO2 to be used for storage. The proposed sorbent is a ceramic honey-comb structured monolith coated with CaO supported on a high-surface area alumina. CaO is a natural acceptor of CO2 and our design ensures the physical stability and chemical reactivity of CaO over a large number of CO2 capture/release cycles. Furthermore, the use of the monolith ensures a uniform flow through the reactor, minimizes pressure drop across the reactor, and maximizes the surface reactive area. In this paper, we will present the results from a flow-through laboratory-scale reactor that establishes the efficiency of the proposed system to capture CO2. Future applications of the reactor include integration within the new-generation coal gasification power plants, such as IGGC, as means of providing decarbonized electricity.

Jan 1, 2010

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The response of the surrounding rock mass to the creation of mining excavations determines the ultimate load on a pillar support system. In conditions where the ground is relatively soft and weak, the full overburden weight can be transferred to the pillar system. However, in stiffer and stronger rocks, a greater portion of the overburden load is transferred to the unmined coal barriers or abutments, and the pillar stress is reduced. This paper makes use of numerical models to examine the interaction between typical pillar systems and the surrounding rock mass for weak and strong geological conditions at various spans and depths of cover. The concepts of structural failure and functional failure of pillars are used to assess pillar performance when pillars are deformed beyond their peak resistance. The results show that the span-to-depth ratio is an important factor in determining the pillar stress and the ultimate deformation of pillars. The ultimate pillar strain appears to be closely related to the functional success of pillar systems.INTRODUCTIONThe National Institute for Occupational Safety and Health (NIOSH) was requested by Congress to study the safety of retreat pillar mining following the Crandall Canyon Mine disaster that took place near Price, Utah in August, 2007. As a part of this study, an investigation was made to better understand how the rock mass responds to the creation of mining excavations and how the loads are distributed among the pillars and the surrounding abutments or barriers. The outcome of these investigations contributed to the development of a modified loading model for the ARMPS-2010 (Mark, 2010) method ofretreat mining pillar design.Structural and Functional Failure of PillarsPillar design is typically conducted by estimating the pillar strength and stress, and then sizing the pillars so that an adequate margin of safety exists between the expected strength and stress. The pillar strength can be defined as the maximum resistance of a pillar to axial compression (Brady and Brown, 1985). If a pillar is loaded beyond its peak strength, load shedding or yielding can occur, and the pillar is considered to have failed as a structure. Structural failure generally refers to a loss of loadcarrying capacity."

Jan 1, 2010

By A. M. Hanna

This paper presents the experimental investigation on the ultimate skin friction of batter piles. The model piles were pushed in medium dense sand deposits at different inclinations up to 30 with respect to the vertical and tested under axial compression loads. The decrease in the total skin resistance with increasing pile inclination can be explained in terms of the reduction of the ave­rage mobilized angle of friction between the pile shaft and sand. The analysis, which takes into account asymmetrical earth pressure distributions around the pile shaft, showed good agreement with experimental results.

Jan 1, 2010

By I. K. Ozaydin

Analysis of piles groups loaded with large bending moments and both vertical and batter piles can be best performed by matrix analysis. In this paper, a case history about a tall marine control tower is presented. The soil conditions at the site and the results of the computer analysis of the piled foundation are summarized. It is shown that the pile loads are indeed less than the allowable load for a single pile. Pile head loads and moments are used in the analysis of the raft foundation.

Jan 1, 2010

By Bolger Witthaus

"High performance production under challenging geological conditions is a product of several parameters. Main factors are the technical equipment and the knowledge in processing. The design and the support system of maingates must also be taken into consideration. The extraction of seams in German underground hard coal mines of RAG in a range of heights between approximately 1.1 and 4.0 m ( 4 and 13 ft) is done by plow and shearer technology. A complete system for quality management of production is required. The process examination of processes begins with procurement of the equipment. Education and training of the engineers and specialists, as well as for the miners are requirements for success as well.This report gives an overview of RAG measures for achieving high performance. Starting with examination of the processes accompanying procurement of equipment, the following important elements are described. Standards in education and training, technical design and elements of automated processing using stateof- the-art in control systems are critical to this system.The application of automation plays a decisive role in modem coal mines. The latest development in German coal mines is the fully-automated shearer system for longwalls. This helps to enhance safety, particularly in difficult ground conditions, by removing the shearer and shield operators from the immediate mining activity.INTRODUCTIONLongwall mining in carboniferous strata in Germany faces various challenges. Different longwall systems are used to mine up to 24 seams, each with a thickness between 1.1 m (3.6 ft) and 4.0 m (13 ft). High stresses due to a depth of up to 1,400 m (4,593 ft) requiring pillars between the panels, require special systems for roadway development, roadway support and reinforcemen.t as well as for longwall advance operations. Two main types of equipment for extraction are shearer and plow systems. While shearers are utilized for seam thicknesses above approximately 1.8 m (6 ft), plow systems can be used for smaller seam thicknesses between 1.8 m (6 ft) and approximately 1.0 m (3 ft)."

Jan 1, 2010

By C. L. Karr

U.S. Bureau of Mines (USBM) research has shown that fuzzy logic and genetic algorithms (GA's) have great potential for industrial process control. A technique has been developed by the USBM in which GA's are used to substantially reduce the time needed to design fuzzy logic controllers (FLC's).This technique shows promise as an efficient, robust approach to developing control systems. The research described in this report is twofold. First, the basic approach to developing an FLC using GA's is presented. The GA-designed FLC is developed for a specific physical system, a pH titration system. Second, empirical results are presented in which variations in the FLC implementation are compared. Specifically, the effects of altering five aspects of the pH FLC are considered: (1) membership function form, (2) number of fuzzy classes, (3) the center-of-area method, (4) implication operator, and (5) fuzzy rule form. Results indicate that (1) the technique in which GA's are used to design FLC's is effective, and (2) when this technique is used, variations in FLC implementation have little effect on FLC performance in a chosen control problem.

Jan 1, 2010

By J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 2010

By Andrew Theobald, Peter Dare-Bryan, Trevor Byers

The use of advanced modelling techniques and the timing flexibility of electronic initiation systems allows for unprecedented control over blast outcomes as shown in several complex blasting problems experienced by the open pit operation Xstrata Ernest Henry Mine (EHM) in north-west Queensland, Australia.

Jan 1, 2010

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By T. E. Sedysheva

The study of Co-rich manganese crusts has reached the level which allows to start prospecting works in the observable future, and furthermore, probably, exploitation of ore deposits. In this connection, among other goals, the necessity to analyze a distribution of ore bed parameters in details is quite urgent. Foremost, these are crust thicknesses in connection with landforms and elements of submarine mountains relief. This report is based on representative sampling made in course of research cruises run by SSC Yuzhmorgeologiya over guyots of the Magellan Seamounts. Crustal covers could overlie seafloor surfaces which are confined to a various landforms and elements of relief under the condition, that they are free of sediments. These are planed parts of a summit surfaces, edges, spurs, rectilinear parts of slopes, intermountain saddles and volcanic edifices. It is known, that crustal thicknesses are different at a various forms of relief [1]. We processed statistically the data around crustal thicknesses, which were sampled by dredging and submersible drilling (Tables 1, 2).

Jan 1, 2010

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010