Search Documents

By M J. Cole, J Zhou, D J. Borrow, S M. Iveson, K P. Galvin, J L. Sutherland

New technologies can easily take around ten years to commercialise. Strong research support is needed in parallel with the process of innovation and commercialisation, in building a deeper understanding of the underpinning physicochemical and hydrodynamic forces that deliver the separations, in achieving improvements, in the deployment of a new technology, and in expanding the innovation platform to create new IP. External investment beyond the research, derived from the genuine value proposition of transformational change, funds the pathway for traversing the so-called Valley of Death.

Aug 24, 2022

By G P. W Suyantara, Y Tanaka, T Hirajima, Y Aoki, K Sasaki, H Miki

The effect of sodium sulfite (Na2SO3) on the flotation behaviour of bornite and tennantite is reported in this work. Flotation tests were performed using pure minerals of bornite and tennantite under various concentrations of sodium sulfite at pH 9. The flotation results indicated that sodium sulfite exhibited a depressing effect on the floatability of bornite in the presence of 0.1 mM PAX. However, tennantite remained floatable after the addition of sodium sulfite in the presence of 0.1 mM PAX. The flotation tests using mixed bornite and tennantite confirmed the flotation results of single minerals. Surface characterisation using X-ray photoelectron spectroscopy (XPS) was performed to explain the flotation results. A mechanism is proposed based on the XPS analysis results.

Aug 24, 2022

By L O. Filippov, A Piçarra, I V. Filippova, N P. Lima, K Silva

The reverse cationic flotation using the starch as depressor of iron oxides is the most efficient upgrading process when is applied to the simple systems composed by hematite/magnetite and quartz. The fundamental studies performed with iron ore samples from different deposits over the world (Brazil, Russia, Mexico) confirmed the inefficiency of starch when the silica content in the concentrate is controlled by Fe/Mg-bearing minerals. The main approaches for solving these issues focused on using new collector formulations or new depressants. However, the alternative depressants tested inhibited flotation of quartz or were less efficient as iron oxide depressant. In this work, a comparison between new amidoamine collector with conventionally used etheramine and oleate collectors in the flotation of pure minerals and actual iron ore samples was performed. The electrophoretic mobility, contact angle and infrared spectroscopy measurements allowed to deduce the hindrance effect as main mechanism of selective adsorption of the amidoamine on the quartz surface compared to hematite and kaolinite. Molecular modelling studies revealed that this steric hindrance effect can be explained by the combination of the "shield" formed by the coordinating water molecules on the (001)-D2 hematite surface and the large volume of the amidoamine head group. The amidoamine tested as collector without use of a depressant showed excellent flotation selectivity allowing the total flotation of quartz from a mixture with hematite. High collector performance and selectivity were confirmed during reverse flotation of quartz using continuous flotation column (D = 500 mm; H = 4000 mm) and allowed to produce the iron concentrates with more than 60 per cent of iron from the rejected slimes samples of Vargem Grande 2 processing plant (Iron Quadrangle, MG, Brazil). The new collector allowed to develop flexible flotation flow sheets to process the iron ore with a complex gangue mineralogy and unlock the old altered tailings and slimes product as new resources

Aug 24, 2022

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022

By J Moffatt, T Payten, N Spooner, L Teixeira, L A. Balzan, G Wilkie, G Tsiminis

Fluorine is a penalty element due to its reactive nature. In acidic environments many fluorine minerals dissolve to form hydrofluoric acid (HF), changing processing conditions. When smelted HF can be released, causing negative effects to nearby people and the environment, as well as potentially damaging the smelter. Sale of ore with high fluorine levels elicit a financial penalty or are banned outright. Real-time sensors create the opportunity for instantaneous decisions on ore processing due to changing conditions. A fluorine sensor would allow rises in fluorine concentration in a processing stream to be flagged, and decisions on processing conditions or diversion to stockpile before processing could be undertaken. As fluorine is a light element, it is difficult to detect with in-field XRF devices and does not work well with PGNAA. There are currently no existing sensors to quantify the presence of fluorine in real-time, and thus decisions based on fluorine grade cannot be made at minute- or even hour-scales. Sensors designed to measure the presence of minerals that contain fluorine are a possible avenue to enable the real-time detection of this element. Mineral-based sensing may also give an added advantage of additional information about how the fluorine will react under different processing steps. The authors were given a grant under CRC ORE II (project number P1–005) to search for mineralspecific signatures suitable for real-time analysis. The work focused on novel regimes and applications of fluorescence as a means to detect specific minerals. The aim was to exploit fluorescence responses unique to minerals of interest in mining systems in order to produce sensors that address gaps in existing capability. After the successful discovery of signatures specific to two major fluorine minerals an additional grant (P1–014) was funded to develop the research into a prototype on-belt sensor, in partnership with Scantech International Pty Ltd. This paper details the development of a sensor package through multiple Technology Readiness Levels (TRLs) through collaboration with government/industry grant schemes, academics from university, and a sensor-focused Mining Equipment and Technology Services (METS) company. We give a brief description of the new sensor technique and provide a case study of multi-disciplinary collaboration.

Aug 24, 2022

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By S. K. Sharma, ANKUSH GALAV, G. S. P. Singh

Providing a suitable protective water barrier pillar (PWBP) is common to reduce inundation hazards in underground coal mines. The imperative factors influencing its performance include the water head acting on the pillar, cover depth, pillar width, strength properties, and permeability characteristics. The mechanical failure of such pillar is a stress-controlled phenomenon, whereas the hydraulic failure is a strain-based phenomenon. A finite-difference numerical modeling approach was developed to study the hydro-mechanical coupled behavior of protective water barrier pillars. The mechanical stability was evaluated in terms of the percentage of failed (ZoF) and intact zones. The influence of the strain-controlled weakening on the permeability of the flow medium was studied through the coupling of the mechanical and hydraulic effects. The coupled steady-state model was used to estimate the outflow rate and its hydraulic stability. The adequacy of the protective pillar was also investigated by assessing mechanical stability and capability to resist hydraulic pressure against the maximum expected water head. A seepage rate-based classification system has also been proposed to evaluate the seepage potential and assess the hydraulic stability. The model has been validated for two case studies at the cover depth of 136–189.5 m and the existing pillar width of 16–42 m against the water head of 25–141 m.

Aug 18, 2022

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By LUKAS FAHLE, Andrew J. Petruska, JURGEN F. BRUNE, Gabriel Walton, Elizabeth A. Holley

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (Lidar) data quality for rapid, digital, and eventually autonomous mine-wide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS provides data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest while reducing SLAM drift error by up to 90%. In collaboration with an operating block cave mine, we confirm these capabilities in field tests on a mine-wide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing, and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate, and comprehensive geotechnical inspections.

Aug 16, 2022

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By Y. FUJII, E. CHANDA, J. KODAMA, D. FUKUDA, M. NISHIHARA, Y. NAKAYAMA, P. SINKALA

For over 40 years, Mufulira underground copper mine has been recording incidents of rockburst. Laboratory tests and numerical analyses were carried out to understand the rockburst mechanism at the Mufulira mine. Rockburst did not occur in the chain pillars or at the mining face, but mainly in the mining drives along diminishing pillars or ahead of the mining face. RQD suggested that the rock mass in the rockburst areas was relatively intact. Laboratory tests confirmed that the rock at Mufulira mine is very strong and brittle. Elastic stress analyses for the rockburst sites by 3D displacement discontinuity method (DDM) indicated very high stress in the chain pillars and low-stress concentration at the sites of rockburst during the initial mining stages. However, there was no apparent positive correlation between the elastically calculated normal stress values and the occurrences of rockbursts. The 2D elastic FEM analysis was conducted under the concentrated stress by DDM and indicated that some stress increase with face advance for the rockburst in the vicinity of the mining face. However, stress severity indicated almost no increase, and the rockbursts cannot be explained as an instantaneous rock mass failure due to stress increase by mining. Therefore, a creep damage model was proposed to clarify the mechanism of the rockbursts. Cumulative rock damage was evaluated for the edge elements of each sidewall of the mining drives, based on the normal stresses by 3D DDM. The rockburst occurrences were well hindcasted. A method to estimate the volume of the rockburst source was proposed, and a likely result was obtained.

Aug 12, 2022

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Dionissios T. Hristopulos, Zach Agioutantis

Methane gas is emitted during both underground and surface coal mining. Underground coal mines need to monitor methane gas emissions to ensure adequate ventilation is provided to guarantee that methane concentrations remain low under different production and environmental conditions. Prediction of methane concentrations in underground mines can also contribute towards the successful management of methane gas emissions. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the USA. The AMS data were stored and pre-processed using an Atmospheric Monitoring Analysis and Database Management system. Furthermore, different statistical dependence measures such as cross-correlation, autocorrelation, cross-covariance, and variograms were implemented to investigate the potential autocorrelations of methane gas as well as its association with auxiliary variables (barometric pressure and coal production). The autoregressive integrated moving average (ARIMA) time series model which is based on auto-correlations of the methane gas is investigated. It is established that ARIMA used in the one-step-ahead forecasting mode provides accurate estimates that match the direction (increase/decrease) of the methane gas emission data.

Aug 2, 2022

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By P. M. Mashaba, S. O. Bada

An advanced high internal phase water-in-oil (HIP W/O) emulsion binder and flotation with an internal dispersed water phase of 95 vol% was used to beneficiate South African weathered coal from discard dumps. Five coal samples with calorific values ranged from 8.48 MJ/kg to 20.94 MJ/kg were utilized. The performance of the HIP W/O emulsion was compared to that of kerosene in terms of the physicochemical properties of the clean coal products. A 5 kg/t emulsion binder addition produced a high-quality coal concentrate with 11.76% ash and a heating value of 28.61 MJ/kg from a sample containing 29.34% ash. Using the same dose and coal sample, kerosene resulted in a clean coal concentrate with 17.47% ash and a calorific value of 26.42 MJ/kg. Further samples were also beneficiated using 5 kg/t of W/O emulsion. The highest increase in calorific value was achieved from the beneficiation of a sample containing 48.71% ash, from 8.48 MJ/kg to 18.16 MJ/kg. It has been established that emulsion binders can upgrade coal samples dumped many decades ago.

Aug 2, 2022

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By F. Nakhaei, M. Le Roux, Q. P. Campbell, S. Botlhoko

The results of coal sink and float tests are plotted as washability curves. Analysis of these curves indicates the most effective method by which the coal can be cleaned. Sink and float experiments are samplingdependent, destructive, and use toxic chemicals. The present research introduces an alternative method based on a 3D imaging system called RhoVol, in which the density of individual particles is determined from mass and volume measurements. A quantitative error analysis was conducted on coal sample density measurements obtained by RhoVol, and the main factors influencing the errors identified and investigated. The results show that the drawback of this technique is related to its not being able to detect hidden concavities in the particle, resulting in an overestimation of particle volume. Furthermore, it is difficult to capture the impact of porosity and cracks on the volume of coal particles obtained from 3D silhouette images. This mismatch between the RhoVol data and sink and float test results has led to attempts to apply neural network (NN) and linear regression techniques to produce a fully reliable model for correction and estimation of coal density. The NN approach offers superior predictive capability over linear regression, and the estimated density distribution is in line with the sink and float analysis. The root mean square error in estimation of density using the NN model was less than 0.05 g/cm³.

Aug 2, 2022