Search Documents

By Sandeep Pattnaik

Spring stiffness of soil and rock at different depth is often required for a pile structural model. If the pile is rested in multiple layers of soil, then it is rather more complex to simulate the soil in a structural model. The spring stiffness will vary based on density of soil strata over the depth. When a pile is socketed in weathered rock followed by a soil layer, a sudden change in subgrade modulus can influence the pile deflection drastically. Determination of soil spring and simulation of the pile in this condition required correct interpretation of subgrade modulus. The conventional approach of pile spring calculation underestimates the spring stiffness by ignoring underlaying stiffer layers. A finite difference method (FDM) of analysis can reasonably estimate the p-y of soil / rock based on subgrade modulus of each layer. However, the transition between the layers can be better simulated as per the deflection pattern of the pile. The lateral deflection of the pile is mainly dependent on the stiffness of soil layer surrounded by the pile. Generally, the lateral influence of a pile varies from 4D to 6D depending on the soil type. Therefore, soil spring stiffness around the pile would require special attention of a Geotechnical engineer to avoid uncertainty in the prediction of pile behaviour. In this paper, emphasis has been given to develop an approach for pile spring stiffness design. A standard software program LPile has been used to develop p-y curves of soil and rock layers at different depths and then converted to soil/ rock springs over the depth. Modulus of Subgrade Reaction as given in IS 2911 (Part2) was also used to correlate the spring value for different type of soil. Obtained analytical results were compared with full scale field trial for lateral deflection of pile. A good agreement between these two approaches has been established. The effect of soil structure interaction in the structural model shall be simulated by assigning an equivalent vertical and horizontal soil spring, which is developed by Winkler’s soil spring approach. A simplified design principle for calculating the pile spring is discussed in this paper. This approach has been extensively used in Mumbai metro elevated line pile design.

Nov 1, 2022

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Patrick Wong

The design of piling platforms is addressed in BRE (2004) for both fine grained and coarse grained subgrades. However, for coarse grained subgrades, piling platform designs can often be overly conservative due to either conservative assumptions on soil friction angle, or concerns over density variations of granular fill, particularly for made-ground. This paper provides guidelines on economic design of piling platforms on coarse grained subgrade by providing recommendations on ground characterization, assessment of soil properties and the use of non-linear stiffness soil behavior. An innovative performance-based design approach is also introduced, utilizing proof rolling with associated testing and interpretation using small strain theory to overcome concerns regarding potential ground variability of made-ground. A case study is presented to demonstrate the successful application of this performance-based approach to avoid having to construct a new piling platform over a 2 ha area. Small strain, non-linear stiffness theory was used to enable a practical proof rolling pressure to be adopted without having to reach the design or ultimate operating pressure. The author considers that the performance-based approach adopted on the case study may be similarly applied to a range of other projects to derive economic solutions.

Nov 1, 2022

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By W. L. Chong

For a project located in Docklands Victoria, a high-rise development was proposed where the geology comprised soils of various compositions and consistencies to approximately 50m deep before being underlain by a siltstone bedrock. Due to the structural loads and spatial constraints, the majority of the foundation piles were designed to be socketed into the siltstone. Key factors in selecting the Continuous Flight Auger (CFA) technique as an effective piling solution are explained. These factors included structural and geological considerations, piling rig capabilities, pile testing regime to verify load performance and integrity, the extensive suite of construction quality controls and instrumentation records required while also achieving an appropriate piling budget and program. This paper also described how these factors underpinned the design approach of the final piling scheme. Critical aspects considered during construction and post-construction quality and pile testing records required to meet and satisfy the strict project piling specifications are also presented. The project adopted what may be considered the “best practice” in deep CFA piling. To the author’s knowledge, this project achieved the record for the deepest CFA piles in Australia where multiple piles to 53.8m deep were constructed.

Nov 1, 2022

By Martin D. Larisch

The construction of diaphragm walls and most large-diameter bored piles (piers) is often carried out under drilling support fluids to temporarily stabilise the excavation prior to concrete placement. In most cases such fluids are either mineral-based slurries (bentonite) or polymer support fluids. The working mechanisms of these two fluid types are fundamentally different. Designers need to consider possible fluid-related impacts on the permanent design performance of the project-specific deep foundations as well as for the temporary excavation stage during construction. Robust design methods for bentonite slurry-supported excavations have been developed in the last few decades and the working principles and associated risks of such mineral-based slurries are understood reasonably well. However, such meth-ods have not been developed in detail for polymer-based drilling fluids. This document provides a brief overview of the main characteristics of bentonite- and polymer-based drilling fluids as a guide for construction practitioners and design engineers alike. The paper also high-lights some common construction risks related to casing installation and the selection of suitable fluid systems for different ground conditions. Typical defects caused by the incorrect application of drilling support fluids, and their pro-active mitigation, are discussed, too. In addition, the basic concepts of sta-bility calculations for bentonite fluid-supported deep excavations are briefly introduced and their ap-plicability for other fluid types such as polymer-based support fluids or water are reviewed.

Nov 1, 2022

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By M.P. ROY, ASHISH K. VISHWAKARMA, A.K. MISHRA, P.K. SINGH, VIVEK K. HIMANSHU

Principal component analysis (PCA) is one of the dimension reduction techniques widely used to classify data based on features. Ground vibration is a major hazard arising from rock blasting operations, and accurate prediction of the vibration is necessary for designing controlled blasting parameters. Most of the widely accepted predictors of ground vibration consider the maximum explosive charge weight per delay (MCPD) and distance as the parameters responsible for ground vibration, but mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, other blast design parameters will also have impacts on ground-vibration intensity. A blast vibration predictor considering all the blast design parameters would be complicated, and some of the parameters will have overlapping contributions to ground-vibration intensity. Data classification using PCA is a feasible solution, and regression analysis may be performed to develop predictors using the classified input data. In this study, PCA was used along with multivariate logarithmic regression to predict ground vibration, and the performance of this technique to predict ground vibration was compared with the performances of various existing empirical predictors. The evaluation suggests that the predictor with logarithmic regression followed by PCA performs better than the existing empirical predictors.

Nov 1, 2022

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on the pressure oxidation (POx) pretreatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach (CIL) approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pretreatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperatures. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Nov 1, 2022

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Machine learning in the form of artificial neural networks was applied to investigate whether specimen load evolution can be predicted as a function of acoustic emission (AE) signals in the case of three-point bending (TPB) marble specimens instrumented with piezoelectric sensors. The ultimate objective of this study is to develop a model that can quantify rock behavior under loading that can lead to rock-failure prediction in underground structures subjected to bending, such as roof failure in development or production openings.

Nov 1, 2022

By Alok Bhowmick

The most uncertain and challenging part of a bridge design and construction is the ‘Choice of foundation’. During the planning and conceptual design stage, it is extremely important to choose the right type of foundation. Wrong choice can lead to disaster for the project. This paper will present three interesting case studies of past bridge projects, to demonstrate how correct choice of foundation can help to meet the project commitments while the wrong choice of foundations can led to huge delay in project completion, leading to time and cost overrun.

Nov 1, 2022

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By O. Craciun, C. A. Bridges, M. Cai, J. Sugawara

There are a number of methods that can be adopted for predicting the ultimate lateral resistance of a free-head rigid pile, from the conventional Brinch Hansen and Broms solutions to three-dimensional finite element analyses. Often these methods give rise to significantly different pile ultimate lateral capacities which could lead to either unsafe or too conservative designs. It is also well known that finding a rigorous and practical solution is challenging due to the complex three dimensional and nonlinear soil-structure interaction. This paper reviews some of the most common methods and produces results of pile ultimate lateral capacities embedded in cohesive or cohesionless soils. Subsequently, a finite element analysis is performed using PLAXIS 3D modelling under the same design conditions. Based on comparison of results, limitations and advantages are highlighted, and the most suitable method is proposed from a practical point of view.

Nov 1, 2022

By Nikolas Schmitz

For today’s construction industry, large-diameter piles are common practice, as they are more competitive than drilling a larger number of smaller piles. More and more piles are installed by drilling rigs, replacing the installation by hammer, vibrators or caisson. Equipment capabilities and technics with rotary drill rigs are highly developed, but very costly and time-consuming when it comes to rock drilling, large diameters and deep foundations. Pile top drill rigs (PBA), based on reverse circulation drilling (RCD) technology, overcome these challenges and are an efficient solution for large diameter drilling (0.6 m to 8.0 m/19.7 ft to 26.3 ft) and drilling depths of up to 500 m (1,640 ft.)in various geological conditions onshore and offshore. The paper will explain benefits of RCD technology and prove this with figures from the Mumbai Trans Harbour Link project.

Nov 1, 2022

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

By Vijay Kumar, Serhat Baycan, Karsten Beckhans

For the deep foundation of podium and tower of the Kuala Lumpur City Centre, BAUER (MALAYSIA) SDN. BHD. constructed 225 bored piles with diameter range of 2.0 to 2.5 m. In order to comply with the depth requirement of the design, for planning purposes and preparation for site, the drilling equipment was required to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to; controlling the open hole stability over time with polymer, installing 70-ton heavy steel cages, pouring up to 550 m³ concrete continuously, in conjunction with installation of kingposts into workable, fresh concrete. The piling works were executed with a BG 72, the biggest drilling rig globally available, and the stringent verticality of the pile bore holes which required approval prior to cage installation. For verification of verticality, Bauer’s patented Drilling Inclination System was successfully used.

Nov 1, 2022

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022