Search Documents

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

Study on Reasonable Mineral Processing Flow Sheet of Yunfu Low-Grade Pyrite Ores Low-grade ores in Yunfu Pyrite Mining Area were investigated, in order to find an economical, reasonable and environment-friendly mineral processing technology, which is of low consumption and high efficiency in pyrite recovering, which can ensure that the quality of pyrite concentrate product is eligible for sale and the sulfur content of the discharged tailings meets the national emission standards. A flow sheet with a classification, a jigging for coarse-grain minerals and a spiral chute separation for fine-grained minerals was adopted, and the sulfur grade and recovery of the pyrite concentrate is 35.50 per cent and 86.70 per cent respectively, while the grade of tailings is only 6.70 per cent.

Sep 13, 2010

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By D. Simon

This paper studies the effect of binder type and content on the early age development of cemented paste backfill (CPB). The early age development of the mixtures is analyzed using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX). These tests show that the early age development of CPB is sensitive to changes in the paste composition. The properties of the CPB depend on the cement content and hydration time. The quantity of hydration products increases with hydration time for all of the mixtures containing cement. However, the high cement content pastes (at least 50% PC) exhibit complete coverage of the PC grains and mine tailings by C-S-H, while the low cement content paste shows scattered coverage of the PC grains and mine tailings and a higher void ratio.

May 1, 2007

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By L Hussey

Mt Keith concentrator treats low grade disseminated nickel sulfide ore supplied from the adjoining open pit mine. It is a traditional crushing, two-staged closed circuit grinding circuit (SAG & Ball Mills), followed by a complex split-size rougher, scavenger and cleaner flotation circuit. In 2016, 10.5 Mt was milled, at an average head grade of 0.54% Ni, yielding 35 000 nickel metal tonnes in concentrate.Historical analysis of the plant data indicated that of all the nickel lost in the fines rougher circuit tails stream, 25.6% was recoverable in an eight minute laboratory scale flotation test. These results implied that this fine nickel was readily available for recovery in the plant, either through operational improvements or additional flotation capacity. With operation optimisation ongoing, and capital within the business focused elsewhere, plant personnel were challenged to think differently about improving recovery.In 2012, a separate project to improve plant recovery when treating high talc ore was completed. Amongst other vessels, this project saw the installation of two 150 m3 Outotec Cells to the scavenger section of the fines rougher, middlings and scavengers (RMS 1) circuit. Since installation, the operation of these cells resulted in difficulties immediately upstream with instability in the scavenger cells. It was therefore decided that these cells would be better suited to treating the fines rougher circuit tails.The alterations required to divert these flows were minimal, with the capital project totalling $220 000.In the two years since installation, the fines rougher tailings nickel grade has dropped by 9.9%. The scavenger circuit has also seen a 2.8% reduction in tailings nickel grade, and instability issues were immediately resolved. This project serves as a lesson in how existing plant infrastructure may be better utilised to maximise recovery. Although this is especially applicable when capital constrained, such re-appropriation can be considered at any point to maximise return on existing assets. CITATION:Hussey, L, 2017. Repurposing flotation capacity at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 254–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By F van de Venter, J Monama, T Kale

For a multitude of years fine iron ore, -1 mm, across the world has been deposited as discard material in tailings facilities. This contributes to environmental problems, decreases plant yield and increases the cost of processing. Fine iron ore recovery processes are often deemed unfeasible or uneconomical, due to the complexity of the reclamation thereof in comparison with high-grade ores. However, recent advances in the recovery of fine iron ore using the Optima Classifier® has shown great promise. The Optima Classifier® is a new hindered settling separator that makes use of an upward current of water for density separation. It’s unique design combines three different separating zones for increased efficiency and recovery. In this study the potential of the Optima Classifier® to produce a +63 per cent Fe concentrate from -1 mm feed material was evaluated from a standalone and process perspective. It was found that a +63 per cent Fe product can be produced from a single stage, using the Optima Classifier®. Fine iron ore feed with an average head grade of 50 per cent Fe was upgraded to average concentrate grades of 63.2 per cent Fe. Displaying upgrade ratios of up to 1.26 in a single stage. A three-stage, rougher, cleaner and scavenger system did however show the best performance with recoveries of up to 70 per cent, yielding 56 per cent of a 63 per cent Fe product. Furthermore, the dewatering of the product and tailings was evaluated using the UltraG ultra-fine dewatering screen ensuring dry, stackable material. The tailings could be used in codisposal, while loads on thickeners and filter presses are significantly reduced. The high throughput of the Optima Classifier® ensures a small plant footprint, minimal civil and structural requirements and low operating utility consumption such as electricity, minimising the carbon footprint of a fines beneficiation plant. The Optima Classifier® in combination with the UltraG dewatering technology has provided a platform for economical recovery of fine iron ore, both current arising and historical. Providing opportunity to lower plant operating costs, reduce environmental liability of tailings facilities and increasing immediate process water recovery

Sep 18, 2023

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016

By J Lyons, M Hasan, D Pepper, C Vadeikis

Processing of large volumes of ultrafine ores has long challenged mineral processing operators because of lower recoveries and increased tailings. This has led to many deposits, or parts of existing deposits, being viewed as uneconomic. As the mining industry can no longer afford to overlook resources that require finer sizes to achieve liberation or result in high tailings losses, the need for technologies to address these issues has increased. Mineral Technologies (MT) worked with a prominent Australian iron ore producer over five years to implement an innovative gravity separation technology for the beneficiation of ultrafine magnetite. The magnetite mineralisation requires a liberation size of <40 μm and selective rejection of ultrafine silica prior to magnetic separation. Through collaboration with the client, MT applied their Lyons Feed Control Unit (LFCU) technology for the beneficiation of finely grained magnetite. LFCUs are widely used in the mineral sands and iron ore gravity plants, and in tailings applications, to recover water and provide constant high density process streams. This project was an extension of knowledge gained from these applications. Test work was conducted on-site, using 1 t/h pilot and 300 kg/hr laboratory scale units. This test work showed that the LFCUs could reject 20 per cent of feed mass to tails whilst recovering >94 per cent of Fe to product. This upgraded the feed from 53.7 per cent Fe and 19.7 per cent SiO2 to 63.8 per cent Fe and 8.8 per cent SiO2. Recovery by size data showed a minimum 88 per cent Fe recovery to product for <8 μm material and up to 98 per cent Fe recovery for the -38+25 μm fraction. The LFCU rejected 70 per cent of <25 μm SiO2. The information obtained from the test work was utilised in the design of the full-scale units which are due for installation at the project site in 2021. This paper outlines the results of this laboratory and pilot scale test work and how the data obtained was used to design the full-sized units.

Nov 8, 2021

By V. C. Rogers, K. K. Nielson

INTRODUCTION The potential health impact from uranium milling operations is mainly associated with long-term releases of radioactive contaminants from the mill tailings.(1,2) The major mechanisms for mitigating these potential releases focus on increasing the tailings containment with the addition of migration barriers such as thick earthen covers and clay liners. Some limited investigation has also focused on reducing the radionuclide source terms. This alternative approach has some desirable features, but stringent cost requirements are placed upon source removal methods in order for them to be economically favorable. A cost effectiveness evaluation is presented herein, in which costs for containment methods are used to establish maximum cost guidelines for the source removal methods. The 230U decay chain, shown in Figure 1 contains the radioisotopes of major concern, 230Th, 226Ra, 222Rn and its short-lived alpha-emitting daughters, When the uranium is removed in the milling process, these isotopes, which are normally not removed remain in the tailings solids. The general pathways to the environment from uranium mill tailings are depicted in Figure 2. The dominant pathways are radon to the atmosphere and radium and thorium to a groundwater aquifer. The magnitude of the contaminants released into these pathways can be characterized by the following parameters: 1. The 230Th and 226Ra content. 2. The emanating power for radon. The fraction of radon generated that is free to migrate. 3. The leach rates. Source reduction methods seek to reduce the magnitude of any or all of these parameters. In general the dose rates are proportional to the source terms. For radon production the source term is proportional to the product of the radium concentration, R, and the emanating power, E, so that the risk is reduced by the same factor that reduces RE. For example, if the radium content is reduced by 95 percent, but E is increased by a factor of two, then the dose rates are reduced by an order of magnitude. The source term for the groundwater pathway is not as easy to identify. The peak in the radium concentrations in the accessable water body can also

Jan 1, 1981

By Henry E. Armitage

The object of this paper is to give a few useful hints on the concentration of low-grade ores. The machines that I shall speak of are, Cornish rolls, revolving screens, Hartz jigs, spitz-lutte, and the Linkenbach buddle (or Roberts&apos;s patent buddle, as it is called in Colorado). I think the reason why some of them have been discarded in favor of more recent inventions is that they have not been given a fair chance to do their work in a satisfactory manner. Cornish rolls are usually looked upon as a machine designed simply to crush the ore as a preliminary to sending it to the sizingscreens, beyond which they have nothing to do with dressing the ore. On the contrary, the rolls give the key-note to the whole process. It is well known that one class of rock will crush differently from another, and from the result obtained by passing the ore through the rolls the size of the first revolving screen and the surface required on the jig-screens must be determined. If it is found that the mineral crushes clear from the quartz, a large mesh can be used on the first sizing-screen, and the tailings will not require recrushing ; but if it is found that some of the tailings from the first jig are ragged (that is, are carrying off particles of mineral sticking on the quartz), it will be necessary to recrush them. Again, if a large percentage of the tailings carry off mineral, it will be more economical to commence with a finer mesh screen than to recrush the tailings. Having determined the best mesh to use on the first sizing-screen, the different sizes on the other screens can be determined from it. I have found for practical purposes that, commencing with a 6-mesh, the next should be 8, then 12, and finally 18. The holes in the jig-screens should be a trifle larger than in the revolving screens. For instance, if the revolving screen is made of No. 14 wire, the corresponding jig-screeus should be of No. 16 wire. The jig-screen surface required for each size made depends on the may

Jan 1, 1890

By John A. Church

When, in 1879,I examined the mines of the Tombstone Mill and Mining Company, at Tombstone, Arizona, I found a bed of tailings containing 12,000 tons, which had a value of 9 to 12 ounces of silver per ton and some gold. The ore had been amalgamated in pans, in which each charge had been ground for four hours, having been pre viously stamped through rough-punched screens, which gave a pro duct varying from 1-100th to 1-20th of an inch, according to the state of wear of the screen. It was certain that a large proportion of the tailings must be in fine slimes, and the question of recovering their value was difficult. Even now the concentration of slimes is . an unwelcome task, and at that day very little was known about it. Nevertheless, after considering the results of a test by repanning the tailings, I advised the company to concentrate and smelt, although they had to face the difficulty of making a smelting-product from slimes containing only 3 per cent. of lead. Limestone was abundant enough, but no iron suitable for flux was to be had for hundreds of miles. One of the company&apos;s claims con tained an argeutiferous manganese-ore, which gave but poor results by amalgamation. This was one reason for recommending smelt ing ; for if manganese would play the part of a precipitant, as iron does, the company could smelt by combining two of its silver ores, without other flux than the small amount of lime that might be needed. At that time no smelter had ventured to trust manga nese as a precipitant, though large quantities of this ore containing silver were bought and used by custom-smelters, who looked upon the manganese solely as a basic flux for silica. I believe that no other furnace has been obliged to trust this metal, and that the man ganese practice of Tombstone remains unique among the records of smelting lead-ores in the shaft-furnace. The bright side of the problem was given by the fact that the mines were shallow and that the enterprise would at least begin with oxidized ores. The tailings contained about 85 per cent. of silica,

Jan 1, 1895

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

By R. J. Mitchell

"Centrifuge modelling of earth structures is a well-proven technique for evaluating the performance of prototype structures using physical models. The applications of this technique have increased dramatically during the last decade such that even the modelling of dynamic responses in structures has been accomplished.This paper presents the first model test results used to design a mine backfill. The models were tested using a 3 m radius 30 g-tonne geotechnical centrifuge which was constructed at Queen&apos;s University specifically for model studies on mine backfill stability and subsidence. The models represent the first production blast-hole stope to be mined at Westmin Resources Ltd. &apos;s H. ~ Mine on Vancouver Island. This paper includes photographs of:model failures in the centrifuge and correlations of model test results with analyses based on unconfined and triaxial test data.IntroductionDuring the feasibility study and development stages for the H.W. Mine, Westmin Resources Ltd. conducted a comprehensive rock mechanics and backfill engineering program. The results of these studies indicated the need for assurance of backfill stability during pillar recovery on the initial blast-hole mining block. The cemented tailings backfill had to be free standing for heights up to 25 m and the potential for surcharge loading from a weak hanging wall zone, the potential for fill block sliding down-dip and the potential for seismic loading had to be considered in the design of the fill strength. The basic questions to be answered were: what cement content is required and will the resulting backfill costs be economic relative to the proposed mining method and sequence? Figure I shows a typical cross-section through the first mining block . The up-dip stope is to be mined first and backfilled with cemented tailings . The down-dip stope would then be mined and filled. Depending on ground conditions encountered, the complete intervening pillar could be recovered and the void backfilled with uncemented tailings or it could be recovered in small sections by exposing limited back and wall areas, backfilling with waste rock and I or cemented tailings . This latter method is commonly referred to as the Avoca method"

Jan 1, 1987

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By Paul C. McWilliams

The U.S. Bureau of Mines has, primarily through its contract program, used large-scale centrifuges to determine design criteria for tailing embankments. The centrifuge runs were made at two installations, the University of Cambridge, Cambridge, England and Sandia National Laboratories, Albuquerque, NM. The major problems considered were as follows: slope stability of embankments, modeling erosion and seepage, use of the phreatic surface level to ascertain the validity of centrifuge modeling, and the effects of compaction and weathering on a tailings embankment. This report summarizes the results of the four test series conducted at University of Cambridge and Sandia National Laboratories. A review of prior centrifuge applications to mining problems is included. Consideration is given to future centrifuge application to mining problems in both soil and rock mechanics.

Jan 1, 1989

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By T Graham

Traditional iron ore wet beneficiation plants are large multilevel structures, often integrated into centralised processing plants. They are characterised by sizeable footprints, substantial water and power consumption, inflexible design and low scalability. Significant design changes that address these issues need to be made before relocatable modular plants become feasible. Firstly, large amounts of processing water are required in standard wet plants, so it is vital that water consumption is reduced to an absolute minimum. Secondly, the process of depositing tailings into tailings storage facilities (TSFs) is environmentally destructive, consumes significant power and requires lengthy approvals to be completed. Thirdly, modules need to be easily and quickly relocatable.The solution to reducing water usage and eliminating TSF requirements is accomplished by providing a tailings dewatering and dry-stacking capability into a separate module. This equipment needs to dewater tailings to a point (typically below 20 per cent moisture) where dry stacking becomes possible – design is mainly driven by material rheology and particle size distribution (PSD). In this respect, a flexible and scalable strategy is employed to dewatering modules, allowing a variety of components such as dewatering cyclone clusters, paste thickeners, fine mesh vibrating screens and filter presses to be used to achieve the necessary moisture level, enabling the final dry stacking to be accomplished by a simple telescopic stacking system. Plant relocatability also requires modules to comply with mass and dimensional constraints, as well as ‘plug and play’ ease-of-use features.For coarse particle upgrade, jigs provide a low-cost and effective solution, whereas fine and ultra-fine Fe units can be recovered using Wet High Intensity Magnetic Separation (WHIMS). Recently, sensor sorting – a dry process using X-ray fluorescence, X-ray transmission, laser or other sensors – has begun to make an impact in coarse particle separation, although capacities are still low. The overall objective of a plant is to provide an Fe upgrade of four to five per cent with a feed of up to 4 Mt/a and a recovery of approximately 50 per cent.CITATION:Graham, T, 2017. Relocatable modular beneficiation creates value from waste, in Proceedings Iron Ore 2017, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017