Search Documents

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By Bertil I. Pålsson

The most common REE containing mineral that is worked today is bastnäsite. It means that mineral processes are adapted to it and that the metallurgical separation techniques for winning of individual REE are adapted to bastnäsite concentrates. For all other deposit types, suitable mineral processing methods and separation technologies need to be adapted and/or developed. Preliminary mineralogical analyses indicate that slightly less than half of the REE in the tailings dumps at LKAB/Kiruna are associated to apatite. The rest is in the minerals monazite (maybe associated to apatite) and allanite. At least allanite is probably not floatable with reagents commonly used for apatite. Mass and element distributions for the tailings sand reveal that very little apatite is present above 300 µm, and that approx. 30 % is below 20 µm. REE does not follow P2O5 completely and are also present in coarser fractions. Flotation results show that the best condition for both apatite and REE winning is pH 9, high collector addition and low dosage of water glass. Under these conditions, the lab-scale flotation gives an apatite concentrate with at least 30 % P2O5 at 70 % recovery. REE follows apatite in the cleaner steps but only partly. Its recovery is approx. half compared with apatite. The reason for the low REE recovery is likely to be that REE to a large extent is trapped in non-winnable minerals, especially allanite. The REE grades in the concentrate are expected to be in the range 3000 ? 4500 g/ton. Keywords: flotation, REE, apatite, monazite, allanite

Sep 1, 2012

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By H. R. Beard

The Federal Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environ¬mental conflicts, impacts, and occupational hazards Associated with mining and mineral processing operations. Tailings and soil samples from Wyoming and Utah were contacted with tailings liquors to determine the degree of absorp¬tion. Absorption ranged from 0 to 99 percent for radium and from 0 to 31 per¬cent for thorium. Some samples, which readily absorbed radium, were contacted with various salt solutions that could be present in tailings solutions to determine their effectiveness as desorbents. The desorption of radium ranged from 0.06 to 100 percent. An alpha-spectrometric method was used to determine the radium and thorium, concentrations in the solutions and the solids.

Jan 1, 1979

By J. Nolan, B. Ande’n, E. Lindgren

Field testing was conducted at the Strassa Iron Ore Processing Plant to evaluate high-gradient magnetic recovery of iron from the plant's tailings. The installation is the first commercial application of the Sala Continuous High-Gradient Magnetic Separator (HGMS) Model 480 Carousel. The objectives of the five-month testing program included optimization of the operating parameters using SSDEVOP techniques to maximize iron recovery, along with establishing a long-term operating history for the SALA 480 HGMS Carousel. The effectiveness of the optimization procedure, the net benefit in term of iron recovery, and equipment performance are discussed in the paper.

Jan 1, 1983

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By Barbara C. Williams

U.S. Bureau of Mines researchers conducted field studies at an abandoned copper-gold mine tailings impoundment. Pore water quality was analyzed in the vadose and saturated zones. Three statistical procedures were employed to summarize the variability within and between the two zones. The results indicated that linear combinations of those variables reflecting sulfide oxidation and aluminum-silicate weathering best summarized the variability in each zone, and that the zones were most different on the basis of sulfide oxidation variables. The geochemical computer code WATEQ4F was used to assess the solubility status (saturation index) of minerals. Saturation indices of sulfide oxidation and aluminum-silicate weathering minerals were different in the two zones. It was demonstrated that the statistical analyses produced similar and complementary results to the geochemical code.

Jan 1, 1992

Planning for the Macraes Extension project highlighted the need for additional tailings storage availability. The possible solution of developing new tailings impoundments in Northern Gully, in tum, led to concerns being expressed by the regUlatory authority over the assimilative capacity of Deepdell Creek. Philosophical differences over the appropriateness of applying a seepage model used to set standards in consents for the original project resulted in the company re-evaluating the whole monitoring system associated with tailings disposal and seepage control. Re-evaluation indicated problems arising from the existing in-stream water quality monitoring in respect of protection of the aquatic ecological system and verifiability of results. A new monitoring system was designed relocating the compliance monitoring point out of the stream and into the gully containing the tailings impoundments giving greater certainty of monitoring results to all parties and providing improved protection for the aquatic ecology of Deepdell Creek.

Jan 1, 1993

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

With the declining of high-quality hematite and magnetite iron ore reserves and the increasing accumulation of material resulting from mining and beneficiation operations that appear as lowquality depots and discharged materials in tailing dams, the necessity of recycling these reserves is increasingly becoming a critical demand. The Chadormalu iron ore mine is among the largest deposits of magnetite-hematite iron ore in Iran. In this mine, the total wet processing tails accumulated in tailing dams are over 92 Mt containing 25–40 per cent Fe. Laboratory and pilot tests on tailing samples led to the design and implementation of the Chadormalu Tailing Recovery plant (CTR) with a unique process circuit in Iran. In the CTR plant, after three steps of re-pulping with spiral classifiers and sanding machines, the underflow is concentrated by two stages of WMIMS and produces 64 per cent Fe grade magnetite concentrate. The tailings of the drums are mixed together and introduced into the hematite recovery section, including two stages of VPHGMS separators, and 60 per cent Fe grade hematite concentrate is produced. This plant has been in operation for over ten years with a total yield of 18.93 per cent. Due to changes in the materials extracted through new tailing dams, the quality of the final concentrate dramatically dropped to 56.36 per cent Fe and 0.79 per cent P; therefore, applying reverse flotation and removing phosphorus from the final concentrate was inevitable. By using this approach, upgrading of the concentrate to 63.01 per cent Fe and 0.05 per cent P was obtained. Furthermore, regarding the high amount of phosphorus in the tailing streams, direct flotation has been designed to produce apatite concentrate as a by-product stream through a flotation system comprising series banks of Rougher, Cleaner, and Re-Cleaners flotation cells. Hence based on the results, at optimum conditions, a final apatite concentrate with a yield of 15.78 per cent and 14.06 per cent P could be achieved. Successful implementation of this project has led to the production of magnetite-hematite and apatite concentrates with annual capacities of 250 000 and 45 000 t, together with total yields of 11.59 per cent and 6.19 per cent (includes de-sliming of apatite flotation feed), respectively.

Aug 24, 2022

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By E Ruhanen, S Kauvosaari, M Kosonen, C Meintjes

The Yara Siilinjärvi plant is located in the central part of Finland. Siilinjärvi is Western Europe's only apatite mine and annually it produces 1 Mt of apatite concentrate, which creates approximately 10 Mt of tailings.At the beginning of 2017, tailings handling in Yara Siilinjärvi was brought to a new era, by replacing the conventional tailings storage facility with a new tailings treatment plant. The new high-density tailings disposal system with two paste thickeners increased the percentage of solids in the slurry from 45–48 per cent to 66-68 per cent, making it possible to deposit as a paste. This extended the life-span of the current tailings storage facility by 15 years; from 2020 to 2035.This paper presents the storyline of the Yara Paste Plant Project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After some successful pilot trials, the final process design was implemented. Process instrumentation and automation played a key role in the project, as the aim of the Yara Project was to make the plant operable remotely from the main plant. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances.This paper discusses the results from the Yara site since the new tailings treatment plant commenced. Some of the main points are that the operation has been running consistently with an underflow solids content of 66-68 per cent, with average beach slope angles of 3.5 degrees in the tailings disposal area. This control system additionally facilitates minimum use of flocculant, which delivers significant savings to operating costs. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the Paste Plant. During the first year of operation, the plant’s availability has been very good, over 97 per cent.Currently, the plant still has its own staff working there during the daytime, but the Paste Plant is now already operated remotely during the night shifts. The long-term goal is to gradually transition into operating the plant completely remotely.CITATION:Ruhanen, E, Kosonen, M, Kauvosaari, S and Meintjes, C, 2018. Optimising the operation of paste thickening at the Yara Siilinjärvi Plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 297–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By J. Stawovy, A. Fourie, J. D. Quaranta

Coal refuse impoundments are disposal facilities specifically designed for the coal mining industry. Re-purposing refuse impoundments for co-disposal with natural gas flowback water and waste rock overburden has been investigated. The aims of this study were to investigate properties of coal refuse classification under the influence of co-disposed wastes as geochemical material exposure pathways from hydraulically exposed sodium and calcium ( Na+, Ca2+) cation loading from disposal of flowback water produced during the development of horizontal drilled natural shale gas frack wells, and waste rock having limestone characteristics. The geotechnical index classification of saturated cohesionless refuse is required to evaluate the liquefaction potential for strain or strength loss contributing to ground movements. This study is relevant to identifying changes in the coal refuse geotechnical index classification as sand-like, clay-like, or a borderline transitional material from the effects of ion and waste exposure in the impoundment’s reservoir porewater. Laboratory geotechnical tests were performed on fine coal refuse blended with different cations to classify the altered plastic behavior and index classification. Following determination of the index classification, the specimen’s stress–strain responses were investigated through isotropically consolidated undrained (ICU) triaxial compression tests. This experimental study culminated with two salient findings: the first is that introduction of ions alone into the refuse tailings or impoundment porewater resulted in significant material changes in property index classification, and the second finding was that the difference in refuse index classification did not correlate into noticeable effects of the monotonic undrained triaxial strength parameters.

Jul 5, 2022

By D B. Donato

Gold mining cyanide-bearing solutions can pose a risk, cause significant wildlife deaths and adverse public relations and result in non-compliance with regulatory conditions. The International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code) was developed as a voluntary code to encourage industry-wide improvements in managing cyanide responsibly. The Code requires design and implementation of robust monitoring programs for compliance under the following standards of practice: 4.1, 4.4 and 4.9. A robust monitoring regime can be complicated as each processing and tailing system is different. The following systems are commonly used in Australia: carbon-in-leach (CIL); carbon-in-pulp (CIP); heap leach process ponds; tailing waste disposal systems; peripheral discharge, central discharge and in-pit disposal. Some terrestrial wildlife can be denied access by fencing tailing storage facilities (TSFs) or other physical barriers, therefore limiting wildlife interaction with cyanide-bearing tailing and solutions to mainly birds and bats. While wildlife monitoring programs for processing and TSFs contain similar core attributes, it is necessary to adapt monitoring to take into account the site-specific features of each system. These core attributes are discussed in this paper, with reference made to cyanide concentration and associated methodologies. The issue is considerably complicated if tailing solutions are deemed or discovered to be toxic to wildlife. Essentially cyanides are required to be measured to gain an understanding of the concentrations to which wildlife may be exposed. This usually equates to measuring the cyanide concentration of solutions entering and leaving a tailing system. To assess the risk to wildlife presented by tailing and heap leach systems it is necessary to monitor both the hazard (cyanide concentrations) and the exposure (live wildlife species, presence and interaction). These tasks need not be arduous and a system of simple frequent monitoring has been developed and implemented for Code compliance. The wildlife monitoring developed by Donato Environmental Services (DES) and used at mining operations departs from the industry norm. It documents observer effort, live wildlife presence, habitat and behaviour in a tailing system, as well as deaths and carcasses. A greater understanding of wildlife cyanide toxicosis associated with this monitoring approach will enable mining companies to adopt a proactive approach to significantly reduce, or preferably eliminate, the impact on wildlife and assist in gaining Code compliance.

Jan 1, 2007

By Jacques H. Nantel, James F. Archibald

"Frozen tailings material may be required, in the future, to perform the support functions of underground backfill in mines located in zones of permafrost, notably in the high Arctic. To date, no knowledge of physical support parameters of such materials has been obtained in Canada due to the limited mining activity in permafrost regions. It is therefore judged essential that the important physical and mechanical properties relating to frozen tailings material be assessed.Innovative mining methods will be required to cope with the harsh environmental conditions that exist at mining sites in the Canadian Arctic. A preliminary laboratory study, in the absence of field trials at limited Arctic mining sites, has been completed in which the physical and mechanical properties of several types of representative mill tailings mixtures have been investigated. A variety of tests, to determine frozen slurry and pelletized tailings strength properties, moduli of compression, optimum water contents, deformation characteristics and the like, have been conducted.The results of this study will be used to establish guidelines for the suitability of tailings use in such northern mining environments. IntroductionFrozen tailings material has never been used to backfill underground openings in Canadian mines. At present only one Canadian mine, the Polaris Mine situated on Little Cornwallis Island, is investigating the use of frozen backfill. However, the Canadian North covers a large territory and potentially contains a large number of mineral deposits. The understanding of concepts related to mining activities in sub-zero frozen ground is therefore important.The implications of using frozen tailings as underground backfill material are far reaching both from the point of view of mine stability and disposal of tailings in the arctic regions.The strength of frozen materials (soil, backfill, etc.) may take on different meaning depending on the engineering situation. Both the concepts of rupture and excessive deformation need to be considered.The functions usually required to be performed by the backfill material in underground mines may be summarized asfollows:a) working floors; such as in cut-and-fill stopesb) stope wall support; for cut-and-fill and delayed fill stope~c) self-support when backfill is exposed on one face; during pillar recovery phases.For fill functions such as working floors, the short-term response of the frozen fill is the dominant concern. For the other fill functions, the long-term deformation response of the frozen fill, or creep, is of interest."

Jan 1, 1986

By E. Niehuis, J. Y. Kim, H. G. Cramer, S. L. Chryssoulis, K. G. Stowe, C. Bendel

TOF-SIMS was used to detect, identify from parent molecular ions and determine the relative concentrations of collectors sorbed on the surface of mineral particles in concentrate and tailings samples from three Canadian concentrators. In the Kidd Creek Zn circuit, sphalerite lost to tailings carried on average a quarter of the amount of isobutyl xanthate present on that recovered to Zn concentrate; amyl xanthate, which is not reported as added to the circuit, was also detected on floated sphalerite and pyrite. At Brunswick, sphalerite particles lost to the scavenger tailings had ten times less amyl xanthate and isobutyl xanthate than those recovered to the Zn final concentrate, while both xanthates were detected on sphalerite floated to the Cu-Pb cleaner circuit. At Matagami, significantly more isopropyl xanthate and isopropyl dithiophosphate were detected on sphalerite recovered to the final Zn concentrate than on that lost to the Zn rougher tailings

Dec 1, 1995