Search Documents

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

By J. A. Wates

The paper examines the consequences of dam building with slime of high water content, and therefore Iow relative density, such as the tailings usually associated with the extraction of uranium. It shows how a Iow relative density reduces the practical maximum rate of rise, and hence the establishment cost, of slimes dams built by conventional means. Further hidden costs of such tailings dams are examined. It is concluded that dewatering of tailings before their disposal is the most cost-effective means of increasing the rate at which a particular dam can be constructed, or of reducing operating or stability problems on existing dams. In the longer term, underground disposal seems to be a feasible alternative. However, it is pointed out that there are other factors that can compound the operating difficulties, and that these should be investigated before remedial steps are taken.

Jan 1, 1983

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high-density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are capable of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadings. Final capital expenditures for the project approached $10 million and annual operating costs are about $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described.IntroductionCominco Ltd. has worked the Sullivan orebody at Kimberley, B.C. since 1909 and has operated a concentrator some 5 km distant from the mine since 1923. Over the last 70 years, in excess of 120million tonnes of ore have been mined, and production continues at an average rate of 6,500 tonnes per day. It is a well-known fact that the contribution of this operation to Canada's mining industry and, in particular, Cominco's development has been significant. However, this success has not been without some undesirable side effects.Unfortunately, the Sullivan is one of only a few major Western Canadian orebodies which may be classed as ""acidic"" in nature. That is, the primary economic minerals, galena and marrnatite, are enclosed in a siliceous host rock with abundant pyrrhotite, but with little or no accompanying alkaline gangue minerals such as calcite and dolomite. The unavoidable consequence of mining such an ore is that contact with air and water generates an acid mine drainage containing various soluble metals orginally present as minerals.This problem also arises in the concentrator's tailings ponds, which, in the case of the Sullivan, are two separate impoundments of different materials. The 1,100 tonnesl day of ""iron"" tailings are primarily pyrrhotite which is surplus to the requirements of a separate operation that produces sulphuric acid as an intermediate to phosphate fertilizers. Inert gangue minerals with only a minor sulphide content are the main constituents of the 1,200 tonnes/ day of siliceous tailings. Corresponding to the relative proportion of sulphides in the solids, the decant from the iron tailings is substantially more contaminated than that from the siliceous pond."

Jan 1, 1980

By Herry Poernomo, Agus Prasetya, Iga Trisnawati, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Panut Mulyono

We studied yttrium extraction from untreated zircon sand processing waste tailings. Xenotime mineral as the rare earth element source with an abundance of yttrium (REY) was detected in sufficient grade for extraction. As much as 9.03% yttrium exists in zircon tailings (analysed by X-ray fluorescence spectrometry). The presence of yttrium was confirmed by X-ray diffractometry in xenotime minerals, which are yttrium carriers (Y-PO4). The purpose of this research was to determine the effect of leaching conditions on yttrium recovery from zircon sand after alkaline fusion treatment. Alkaline fusion was chosen to decompose phosphate into hydroxide in the xenotimemineral,which will reduce further required hydrometallurgical processing.Alkaline fusionwas carried out for 3 h at 450 °C, with a ratio of sodium hydroxide to zircon tailings sand of ~ 1:1. The alkaline fusion product was leached with water, followed by hydrochloric acid treatment to leach the yttrium. Yttrium recovery reached 87% under optimum conditions (60 °C, 1MHCl, and solid-to-liquid ratio = 1/10 for 7.5 min). A suitable model for yttrium dissolution with hydrochloric acid was diffusion through a solid particle ash layer. The calculated activation energy (EA) for this model was 20.21 kJ/mol.

May 26, 2020

By S Jeon, K Haga, A Shibayama, L Godirilwe, C B. Tabelin, I Park, A Buronov

Open pit/underground mining and mineral processing can generate large amounts of waste that contains sulfide-type minerals such as pyrite (FeS2), and it can produce acid mine drainage (AMD) when exposed to oxygen and water. This highly acidic wastewater contains heavy metals and this is one of the most serious environmental issues after mining operations taking several decades to completely remediate with high costs. For green mining, the present study focused on the development of a recovery technique for gold from an eco-friendly solvent, thiosulfate, by utilising mine wastes, tailings. First, gold recovery experiments in ammonium thiosulfate system were carried out using model samples representatively present in tailings (ie SiO2, Al2O3, FeS2, Fe2O3, and Fe3O4). The results showed that gold recoveries were negligible when using Al2O3, SiO2, Fe2O3, and Fe3O4 while pyrite shows a recovery efficiency three-fold as high as the maximum recovery efficiency when using others. Subsequently, the study also addressed the identification of the recovery mechanisms and post-recover process. The results indicate that tailings can be sufficiently utilised for gold recovery in the hydrometallurgy process and a further sustainable process can be established.

Sep 1, 2024

By D Kotzen

Online cyanide analysers have been successfully used to control free cyanide in the gold/silver leach process for over 15 years. Use of such analysers leads to cyanide savings and improvement in recoveries. Plants with leach cyanide analysers show both lower and more consistent cyanide levels in tailings. Cyanide code compliance requires meeting residual cyanide targets in tailings. Monitoring and logging of the residual cyanide in plant tailings and effluent is required. Meeting targets may require cyanide recovery/destruction processes to be implemented. The operating cost of destroying cyanide is often the same order of magnitude as the cyanidation cost. Various cyanide destruction and/or recovery processes are reviewed. Choice of a process consistent with the environmental and operational requirements is illustrated. Online weak acid dissociable cyanide (CNWAD) analysers have recently been developed and introduced on gold plants. The application of a WAD 1000 online CNWAD analyser at a large gold plant is presented. The analyser ensures code compliance, reduces cyanide destruction process operating costs and forms a historical record of CNWAD values in tailings.

Jan 1, 2007

By P. R. Bremner

In keeping with its mission to maximize mineral and metal recovery from domestic sources, the Bureau of Mines investigated a method to extract silver from tailings not amenable to cyanidation. Results of a laboratory study on the recovery of silver from cyanide tailings containing 1.7 ounces of silver per ton by leaching with an acidic ferrous chloride-sodium chloride solution are presented. The effects of reagent concentration and reaction time on the leaching of silver were investigated. A leaching solution containing 5 wt-pct NaCI, 2.5 wt-pct FeCI2, and 1.2 wt-pct HCI (for acidity) extracted 82 pct of the silver from the tailings during a 24-hour leach. The amount of HCI consumed during the leach was 46 pounds of HCI per ton of feed. Only 23 pct of the silver was extracted by conventional cyanidation. Ninety-nine percent of the silver was recovered from the pregnant solution by cementation onto iron powder.

Jan 1, 1982

By Murray D. Fredlund

The consolidation of soil material is central to many types of engineering analysis. Problems such as the building of highway structures, landfills, or buildings over saturated soft clays require application of such theory. It has been found in industry that the application of consolidation theory has lagged significantly behind the theory which has been developed some time ago. The application of small-strain saturated consolidation theory was first proposed in a 1D form by Terzaghi. Although this theory has been available for some time it?s implementation into software packages in 2D and 3D forms has been slow due to inherent complexities in the coupling equations. The flow and stress equations are also inherently somewhat unstable and this further complicates software implementation. Of particular interest in the mining industry is the consolidation of uranium tailings. One such disposal method that has been utilized is the subaqueous deposition of uranium tailings in large pit structures. When performing such deposition the calculation of consolidation rates is central to determining final pit capacity and expected life. Consolidation software can be successfully used in such cases in order to determine pit filling rates. The primary complexity, however, is that tailings are typically deposited in slurry form and therefore the potential deformations are large. Large-strain consolidation theory is therefore required in order to properly solve the deformations over time. This paper presents the use of a large-strain consolidation analysis in order to predict long-term filling rates in a uranium tailings pit.

Aug 1, 2010

By S. Triantafyllidis

The tailings produced from the Kirki (Agios Filippos) high sulfidation epithermal deposit processing plant are laminated, weakly cemented and their particle size ranges from fine sand to fine silt. They are mainly composed of milling residues of gangue (quartz, dickite/kaolinite, pyrophyllite, illite); sulfides and secondary minerals (jarosite group minerals, butlerite, anglesite, beudantite and gypsum) are present to a lesser extent. They have high Pb and Zn (average 0.75 % and 0.57 % respectively) and low S (1.04 to 2.92 %), Cu, As, Cd, Ni and Sb content (average 248, 163, 59, 27, 20 g/t respectively). Stagnant waters forming small ponds on the surface of the impoundments exhibit low pH and high heavy metal and sulfate concentrations. Negative Net Neutralization Potential (NNP) characterizes the tailings, indicating moderate to high potential for acid generation. Application of the TCLP test revealed that the tailings are characterized as toxic because of the increased solubility of Pb and Cd. On the other hand, As TCLP solubility is very low.

Jan 1, 2006

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

By L. Petzold

The demand for stainless steel is ever-increasing. As an essential element in stainless steel-making process, so is the demand of chromite concentrate. At the same time, the industry proven technologies for beneficiation of chromite are limited. Chromite is only crushed, screened and jigged to produce a concentrate. However, for ultrafine and low-grade material, no satisfactory beneficiation methods for the enrichment of chromite fines exist in industrial operation. This poses a clear challenge for the industry, which Primetals Technologies has addressed with the development of a new beneficiation process. The aim of this process was to enrich low grade chromite tailings to a quality suitable for the smelting process. Required concentrate grades are different over the world, concentrate grades of Cr2O3=40% and lower are found at the Bushveld Complex, South Africa. The target for the present study was a Cr2O3-grade in the area of 49%. Three different chromite tailings with Cr2O3 grades between 16 % and 29 % were part of a study, executed by Primetals Technologies. All three tailing materials were characterised by Mineral Liberation Analysis (MLA). Based on the physical, chemical and mineralogical findings, process flowsheets were developed. The process flowsheets included grinding to ensure a full liberation of the chromite. The liberated material was classified at a cut size of 63 μm to a coarse and fine fraction. Gravity separation and flotation processes were tested with the coarse particle fraction. Due to the limitations of gravity separation with fine particles, only the flotation process is suitable and was tested with the fine fraction < 63 μm. A Design of Experiment (DoE) with six factors, each three levels, was conducted to identify optimal parameters for the fine chromite flotation. Two different collectors were tested: a phosphoric acid ester and a fatty acid type collector. In small scale test work a chromite concentration suitable for the smelting process was achieved. On this basis Primetals Technologies will develop a pilot-scale test program to research recirculation effects and upscale potential of the process. Keywords: Mineral processing, tailings beneficiation, flotation, density separation, process development, chromite

Jan 1, 2020

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

By Junio Simões Pereira, Carlos Magno Nascimento, Frederic Yann Armache Braga, Luiz Cláudio Monteiro Montenegro

Given the current scenario experienced by Brazilian mining industry, the study and development of technologies that enable a more secure and controlled disposal of tailings has gained significant relevance. Among the various alternatives and disposal methodologies, Anglo American has been developing tests on three study fronts: dewatering polymers, hydrocyclone dewatering and pulp filtration. The first two fronts are intended to optimize the way of occupying the existing tailings dam. The filtering is intended to reduce the mass transfer to the reservoir, extending the life time of the existing structure. The studies were divided into laboratory, pilot and industrial phases, aiming at proving applicability and scheduling for a definitive future installation. Until this moment, all tests have demonstrated gains and potentials of applicability.

Oct 3, 2019

By Brett D

Tailings disposal and water management are one of the most important environmental issues in mining projects. The nature and the method of disposal of the tailings will determine the long term environmental impacts and must be carefully considered at the planning stage so that final abandonment can be economically achieved. If not, long term and on-going treatment and amelioration may be required to achieve environmental standards. Final abandonment requires dam safety surveillance inspection to satisfy engineering stability and hazard requirements as well as environmental issues. Environmental issues include stability, as well as rehabilitation and long term contamination potential.

Jan 1, 1991

By Farzaneh Abedini, Narain Hariharan, Lucas C. McFarlane, Nikolas A. Romaniuk, Tiffany Thayne

The use of dewatered mine tailings as backfill material (commonly referred to as ‘paste’ backfill), is the most practiced form of backfill in Canada providing significant environmental benefits by reducing the size of external tailings facilities and improved economics through enhanced resource recovery. Paste backfill operations reuse filtered mine tailings with a cementitious binder and water to create a slurry that is hydraulically transported to refill underground stopes, later forming a structural network of cemented tailings in the mine stopes. Unlike typical structural applications that utilize General Use (GU) Portland cement; modern paste backfill operations maximize strength performance by blending Portland cement with ground granulated blast furnace slag (GGBFS) or other supplementary cementitious materials (SCMs). GGBFS and other SCMs offer key performance benefits and carbon reductions; however, the availability of these SCMs is rapidly dwindling in today’s carbon-constrained economy. This paper examines the development of an alternative binder system that provides similar performance and carbon reduction to that of GGBFS for mine backfill operations. The binder utilizes the chemical reaction between a reactive source of aluminosilicates and available calcium from calcium oxide or calcium hydroxide to replace between 50 to 100% of GGBFS. The performance of the binder is examined with insights into the hydration mechanisms that generate mechanical strength in the cemented paste network. Paste backfill slurries require precise engineering to create a material that maintains flowability during pipeline transport and generates enough strength to meet operational targets once placed in the stopes. Engineering of such slurries requires large amounts of water to be added to the binder-tailings matrix, far exceeding the typical water to binder ratios used in concrete mix designs. This characteristic of paste backfill warrants great emphasis on understanding the hydration mechanisms of the binder used in the paste backfill system. GU cement is typically composed of 50-70% tricalcium silicate and 15-30% dicalcium silicate.  The hydration mechanisms of these compounds consume 4 to 6 units of water to mineralize into calcium silicate hydrate cemented phases that result in compressive strength development. Cementitious aluminate and aluminosilicate phases make up 5-20% of GU cement and aid in secondary performance characteristics such as set time. Certain calcium aluminate hydrate phases such as monocarboaluminate and ettringite mineralize 10 to 32 units of water into their crystalline structure. Hydration products such as ettringite are traditionally avoided in construction applications due to their propensity for volumetric expansion after cement setting, leading to micro-fissures and subsequent strength degradation (known as ‘sulfate attack’). This paper proposes that such hydration products benefit the strength development in paste backfill slurries with the aforementioned characteristics due to their greater potential to mineralize free water. The newly developed calcium aluminosilicate binder is designed to replace 50-100% GGBFS or other SCMs used in paste backfill systems and meet operational strength requirements by providing exceptional hydration characteristics through cementitious reactions. Additionally, the aluminosilicates used have a minimal carbon footprint and a secure supply outlook, thereby allowing mine operators access to a low-carbon binder option throughout the mine’s lifespan.

May 4, 2025

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By J. Oré

An alternative method for dewatering slurry (tailings) is the use of geocontainers (MacTubes). The practical application of this work was carried out in the concentrator plant of the Raura Mining Company, located in the occidental mountain between Huánuco and Lima in Peru?s central highland. For the development of the research, the MATLAB R2012a software MGeST (v. 1.0) was used (Slurry Geocontainer Maccaferri Treatment). MGeST is used for sizing MacTubes, which allows determination of the most important design parameters, such as height (H), filling residual pressure (P1O ), strength of geosynthetic (T), and dehydration height. Compared with GeoCoPS v. 3.0, there is a maximum difference of 3% between the results obtained. The tailing to be treated in the MacTube have a specific weight of 11.62 kN/m3. After several tests it was determined that a MacTube of an apparent opening size of 0.22 mm was required for this specific weight.

Aug 1, 2013