Search Documents

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By C. Y. Garber

INTEREST in the sink-float plant operated by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, has recently been largely confined to the preparation and reconditioning of the galena medium. The ease and simplicity of these operations in a concentrating mill producing a flotation lead concentrate has occasioned enough comment to possibly justify a brief description. The subject is treated from an operator&apos;s viewpoint only; no effort is made to discuss it in a theoretical or technical manner. PLANT AT BUNKER HILL The sink-float plant was first operated in December 1941. It was built for the purpose of quickly increasing mill capacity with a minimum of equipment. It is the Huntington-Heberlein sink and float process using galena medium and is operated under license from the Sink and Float Corporation, New York city. Lead-zinc ore from the Bunker Hill mine is crushed to pass a I ¼ in. screen and is then washed and separated on vibrating screens having 4 ½ -mm. round-hole punched plates. The screen undersize, amounting to 33 per cent of the mill feed, is dewatered and sent to the ball-mill feed bins. The screen oversize goes to the sink-float plant, where 50 per cent of the oversize, or 33 per cent of the mill feed, is float, which is washed free of medium and disposed of as a tailing. The remaining 33 per cent is sink, which, after washing, is crushed to pass ½ in. and joins the undersize in the ball-mill feed bins. The normal plant capacity is 1700 tons per 24 hr. About 1.7 per cent of the total lead and 3.3 per cent of the total zinc in the feed is lost with the sink-float tailings (Table I). [ ] More complete descriptions of the H. H. process and Bunker Hill sink-float plant are given in several recent articles, listed at the end of the paper. PREPARATION OF MEDIUM AT BUNKER HILL New medium is made intermittently as needed, usually 12 hr. in each 6 days. A small portion of the current mill flotation concentrate is diverted from the lead cleaner cells to a I-in. vertical sand pump and pumped to a two-cell 36-in. Agitair flotation machine, where NaCn and ZnSO4 are added and the grade of concentrate is improved as shown in Table 2. Tailing from this operation is returned by gravity

Jan 1, 1946

By C. M. Kleeman

All mines have a finite life and the time comes when the ore is depleted, or it has become uneconomical, or for some other reason which may be peculiar to that particular mine, it must be shut down. The operation at that point of time still has some assets such as mining and milling equipment, workshops, and in the case of a gold mine, an unknown quantity of gold which has been trapped in the treatment plant. Recovering this gold can be done at small cost and can be extremely profitable. Recovery of these hidden assets requires a good knowledge of the treatment plant, i. e. , as say values of heads, tails, and of the products produced; and if mercury for amalgamation was used, where? A careful study of available plant records can be extremely valuable in forming a working plan for adequate recovery. In the following paragraphs the various unit operations and equipment where gold can collect are described and suggestions made for its recovery. Subsequently, a case history will be given for dismantling a gold plant which had a complex flowsheet and which had been in operation for many years. Looking for trapped gold in a crushing section would invariably not be worthwhile since crushing is normally a dry process and there would be few areas where free gold could collect. In the milling section, however, many areas can literally become small gold mines in themselves. Material in the bottoms of grinding mill scoop boxes can be high-grade, and even the scale on the sides of the boxes should be scraped off and collected. Mill liners should be removed and all scale, rust, and residue collected. Residue in the bottoms of rake or spiral classifiers, if they have been used, should be removed as should the scale and rust on the sides of pump sumps, launders, etc. The following procedures should be used to extract gold from these collected materials. All steel (ball scats) should be removed, screened out, and reserved. Fine material should be placed in an amalgam barrel, water added and ground with the amalgamation tailings being sampled and assayed. If high-grade, tails should be reserved; if not, discarded. The coarse material that was screened out should be placed in a heap, regularly sprayed with water and allowed to rust. After several months this material should be screened again and the fines amalgamated.

Jan 1, 1981

By C J. Ptacek, J G. Bain, D W. Blowes

The passive interception and in situ treatment of groundwater using permeable reactive barriers (PRBs) has, within the past decade, become an accepted remedial approach to the control of plumes containing dissolved organic and inorganic contaminants. Since the first applications of the technology in the early-1990s, there have been several field-scale PRBs that have provided excellent treatment of dissolved metals in groundwater. Additional commercial applications and demonstration projects continue to be developed. Three field-scale applications and supporting laboratory columns have shown that several thousands of milligrams per litre of sulfate, more than 1000 mg/L iron, and several tens of milligrams per litre of other metals can be removed from groundwater by PRBs that promote sulfate reduction. The reactive materials, which incorporate various forms of organic carbon, promote microbially mediated sulfate reduction, the generation of hydrogen sulfide, and the subsequent precipitation of sparingly soluble iron and other metal sulfide minerals. Effective performance has been achieved by PRBs installed at a mine-tailings impoundment in 1995 (Sudbury, Ontario) and at an industrial facility (Vancouver, British Columbia). These PRBs have removed iron and other metals from groundwater. Similar materials were also used to create reactive layers within test cells directly in a tailings impoundment in 1999 (Timmins, Ontario) with the objective of removing iron and sulfate from the pore water before it migrates from the tailings impoundment. Zero-valent iron (ZVI) has been shown to provide excellent removal of chromium (VI) in a PRB, which was installed at the US Coast Guard facility in Elizabeth City in 1996, by reduction and precipitation reactions. Laboratory tests have also shown that ZVI reduces As(V) to As(III), which is subsequently removed from solution by co-precipitation with iron oxyhydroxides. In groundwater containing sulfate, ZVI and mixtures containing organic carbon can promote sulfate reduction and the subsequent precipitation of sparingly soluble arsenic and other metal sulfides. A trial PRB system was installed in 2001 and was shown to attenuate arsenic and other electroactive metals in groundwater at an industrial facility in northwestern Ontario. Basic oxygen furnace (BOF) slag, a waste material generated by the steel industry, has shown excellent potential for the removal of phosphate, elements such as arsenic and water-borne pathogens from groundwater in field and laboratory tests.

Jan 1, 2003

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type3 Prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution. The alternatives to retreat mining with multiple entries are: Modified retreat mining- where the tail-entry is being formed during the mining of-the panel ("2"-system). Some form of advance mining-where the head-entry or both head and tail entries are being formed as part of the longwall extraction process. These methods are well-known and well-established. Variants of them are being practiced in Canada, Central and South America, but not in the US. It is primarily the laws governing ventilation-conceived for room and pillar mining which prevent the rapid development of these techniques. Another aspect of longwall mining is that it requires a systematic and consistent approach in organization, roof control, ventilation and transport. It is for this reason that compliance with health and safety regulation is fairly well ensured if the longwall system has been well laid out and is subsequently well-run. Nevertheless, a management mentality raised in the great flexibility of the room and pillar system cannot always come to terms with the degree of forward planning and rigid discipline required to successful longwall mining. Research, development and other investments in the partial aspects of longwall mining are always of interest, but no massive trend to longwall can be expected realistically unless these major stumbling blocks in the basic law and basic approach are effectively removed.

Jan 1, 1980

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32&apos; x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18&apos; x 5&apos; Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5&apos; x 12&apos; vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer &apos;s underflow are dewatered on a 13&apos;[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By Frederick Laist, Howard Aldrich

The object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the- results obtained. A general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, 20 ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the dots, thus cutting down the draft. The volume of gas through

Jan 1, 1915

By H. S. Martin

Although it was known some years ago at the Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65-mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. Earliest Use of Microscopic Examination of Tailings As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for microscopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral partieles or grains may be classified into scparate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain 110 other included sulfides; 2. Grains in which all three of the copper sulfides are representel (the core may be of chalcopyrite, partially altered to boruite, these two minerals being cntirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite. The grains of free mineral particles are perhaps the most numerous, taking the ore as a whole, but it is noticeable that of the grains of combined or associated sulfides

Jan 1, 1930

By D. L., Hayes

THE concentration of zinc ore in Wisconsin is a comparatively simple process, although it presents problems that must be overcome in an efficient manner in such a way that installation and operating costs are low. As the ore deposits are small, the first cost of the concentrating plant must be low; while the low margin of profit makes it necessary to have the minimum operating costs. The original mills were copied from those of the Joplin district, as most of them were built and operated by Joplin millmen. These served the purpose well; they made a clean concentrate, which was the chief requirement at that time, as most &apos;of the mines were&apos; considerably &apos;richer than the average at the present time, and wages and supplies were also considerably lower. &apos; The apparatus used at present has changed very little in principle. . The grizzly opening has gradually been increased to 12 in. and sometimes no grizzly &apos;is used. The crusher, gradually grew in size, the largest crusher has -an opening of about 24 by 13 in. and a 7/8-in. throw on the. eccentric shaft.

Jan 1, 1921

By Z. M. Wang

A large scale a polymetallic mine in north China is a refractory ore containing many useful com-ponents: W, Mo, Cu and Fe. Mineralogical investigation shows that the deposit is a quite complex one due to fine disseminated size and unevenly distribution of valuable, intergroth of sulphide and tungsten minerals, concurrence of scheelite and calcium minerals. Based on ore characteristic, a flowsheet is used by the floatation processing of sulfide minerals superior to scheelite. Bulk sulphide flotation is used in sulphides. Mo and Cu are floated in sequence after sulphides regrinded. Tungsten mineral is floated using combined depressant that is an effective depressant to gangue, and can improve the grade of rough tungsten concentrate. Compound depressant has high effective in removal of collector in gangue and sulphide, and tungsten is activated also. High quality of tungsten concentrate is obtained at satisfactory recovery. The test production obtains Mo concentrate with grade of 48.16%, recovery of 81.43%; W concentrate with grade of 66.47%, recovery of 78.19%; Cu concentrate with grade of 23.14%, recovery of 56.6%; Fe concentrate with grade of 67.33%. The valuable metals are recovered comprehensively and well techno-economic index is obtained. The mine enterprise profit is increased greatly.

Jan 1, 2014

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

By W. A. Stickney

This report summarizes the results of laboratory tests of five samples of low-grade phosphate ores from Idaho. The laboratory test work has demonstrated that by grinding, desliming, and flotation a portion of the siliceous gangue can be removed. The highly carbonaceous ores responded successfully to treatment after preroasting, to produce a plus-30-percent-P205 product. It has been found that highly siliceous ores, as represented by the samples treated, are more readily amenable to concentration than ores high in calcium carbonate. Of the five samples tested, four were amenable to concentration to a product containing over 30 percent P205. One sample, from the Conda, second bed, was not amenable to mineral-dressing treatment to produce a plus-25-percent-P205 product.

Jan 1, 1955

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By R. Shields

"Hard rock mines move large volumes of material, which can cause the conveyors that are essential to this movement to suffer lots of problems, including carryback, spillage, dust and belt wander. Many of these issues are created at the transfer points where the belts are loaded.This article provides an overview of the latest transfer point systems that incorporate safety and serviceability by design as well as a report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, NV. Here, performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine.The importance of transfer pointsConveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance is the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created.The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material — cargo released in the form of carryback, spillage or airborne dust — that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems and issues with community relations. The U.S. Mine Safety and Health Administration estimates that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points.Technologies to improve transfer pointsA number of techniques to improve the performance of conveyor transfer points have been developed. They include:"

Jan 11, 2017

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By Yury V. Kulikov, Rakan Rahbani, Arkady Y. Senchenko

"The relevancy of complex minerals treatment is constantly increasing taking into account mineral resources depletion. Different refractory ores and concentrates, oxidized and polymetallic ores, as well as metallurgical products (slags) can be assigned to such mineral type. The treatment of such products via conventional flowsheets requires considerable capital and operational costs and does not always provide high recovery level of valuable components into a saleable product. Therefore, considerable amount of ores and metallurgical products are not treated, or treated inefficiently. One of the most promising approaches that allows economic treatment of refractory products is their ultrafine grinding down to 5-20 µm with subsequent processing or hydrometallurgy. Horizontal bead mills - the IsaMillTM, developed by Xstrata Technology, received their wide application in mining industry. Standard testing is performed under laboratory conditions in an M4 IsaMillTM (volume - 4 liters) to define the parameters of fine grinding. This mill completely simulates the operation of full scale industrial mills up to 50 m3 in volume (up to 8000 kW motor). The paper describes fine grinding technology performed in bead mills, and the importance of testing according to a certified method for industrial equipment selection. The paper contains description of promising directions of fine grinding technology application for several projects in Russia and Kazakhstan."

Jan 1, 2014

By E. H. Crabtree

This paper, describing the milling practices at the White Bird concentrator, Picher, Okla., is one of a series on milling practices being published by the Bureau of Mines. The concentrator of the White Bird mine, Canam Metals Corporation, is located in almost the geographical center of the present Picher mining cam&apos; in the Tri-State district, one-half mile east of the town of Picher, 1 mile south of the Kansas State line, and about 18 miles west of the Missouri State line.

Jan 1, 1930

The Bureau of Mines, U.S. Department of the Interior, devised a flotation technique for upgrading chromite in chromium ores and gravity concentrates. The technique consisted of cationic flotation of chromite from a slime-free pulp acidified to pH 2.5 or lower using H2S04 modifier. Flotation results showed that ore containing serpentine as the primary gangue mineral was more amenable to concentration by this technique than ore containing the readily floatable olivine as the primary gangue mineral. Rougher flotation of a chromite ore containing abundant serpertine increased the grade form 19 to 41 percent Cra03 at a chromite recovery of 89.6 percent. Rougher flotation of ore containing abundant olivine upgraded the chromite from 23.4 to 29.6 percent Cr203 at a recovery of 89.4 percent. The technique was also applied to chromite gravity concentrates to further upgrade chromite and to reject silicates. Flotation of a gravity concentrate containing 40.9 percent Cr203 and 4.4 percent SiO2 recovered 90 percent of the chromite in cleaner products containing 44.9 percent Cr203 and 0.63 percent Si02. The combined recovery by gravity and flotation was 87 percent. An economic evaluation of this technique will be undertaken to deter-mine its feasibility for commercial use.

Jan 1, 1980