Search Documents

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By Reza M. Rahman

The froth phase plays an important role in the flotation and upgrading of the final concentrate. At present, the techniques that have been used in the mineral industry to measure the froth recovery have limitations. The aim of this paper is to investigate the performance of the froth in an industrial flotation cell. A unique device has been developed which is capable of decoupling the froth zone from the pulp zone. It consists of two concentric tubes. The inner tube acts as a dropback collection chamber or catcher. The particles that detach from the froth phase fall directly into the catcher and are collected as froth dropback. The froth recovery measurements were carried out in a rougher bank of a copper concentrator treating sulphide minerals. The dropback device is designed so that it can be immersed into a plant size flotation cell and plant froth recovery measurements can be taken at any given time. During the experiments, the bubbles laden with valuable mineral particles entered the device from the plant flotation cell, subsequently rising to form a froth layer at the top of the device. The particles that detached from the froth zone were collected in the dropback collection chamber whereas the concentrate sample was collected by a launder. By drying, sizing and chemical analysis of the concentrate and dropback samples, the froth recovery, was estimated on the basis of the valuable component. The effect of air rate on froth recovery was also investigated. Keywords: flotation, froth, dropback, froth recovery

Sep 1, 2012

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

A pre-flotation process of the Kupferschiefer ore with only frothers produces a concentrate enriched in carbonaceous matter and tailings for further upgrading steps. A partial removal of easy-to-float components of the feed before the main enrichments steps by flotation (rougher, scavenger) improves overall efficiency of separation of valuable elements from the ore. Since the types and doses of frother used for pre-flotation effect the process, the aim of this study was to determine the influence of selected frothers on the efficiency and selectivity of the Kupferschiefer ore processed by KGHM Polska Miedz S.A. A series of pre-flotation tests in the presence of different poly(propylene glycols) ethers, poly(ethylene glycols) ethers and aliphatic alcohols were conducted. The obtained results indicated that the types and doses of frother determine the flotation selectivity of copper and total organic carbon. The evaluation of the pre-flotation process was based on the analysis of selectivity parameters calculated from the recoveryrecovery Fuerstenau upgrading curves as well as the values of copper and organic carbon grades in the flotation products. It was shown that pre-flotation performed in the laboratory scale using a suitable frother provides higher overall flotation selectivity of organic carbon with lower overall flotation recovery of copper in comparison to flotation without the pre-flotation step. Thus, the pre-flotation process improves the quality and quantity of the final concentrates produced from the Kupferschiefer ore.

Jan 1, 2016

By Thi Hien Tran, Ngoc Anh Tran, Thi Thu Hien-Dinh, Duy Anh Dao

"Natural graphite exists mainly in three types of amorphous graphite, flakes graphite and lump graphite. Graphite from Bao Ha mine, Lao Cai province is with 11.8 carbon-graphite %, forms in flakes and dense crystals. The paper presents the comparison among enrichment of Bao Ha’s graphite by two types of froth flotation with 90 g/t kerosene oil as collector, 50 g/t montanol 800 as frother, in natural pH, and at 20 wt.% of solid. The differences among three flow charts indicated that using middling flotation and re-middling flotation for the cleaning tails and the scavenger concentrates, the final concentrate was improved and containing up to 94 carbon-graphite % of flakes graphite, up to 82 carbon-graphite % of fine graphite with 93.48 % total recovery, moreover, carbon-graphite in the final tail is 0.86 % with 6.52 % recovery. However, a refining mill and a classification stage were applied before doing the middling flotation stages.1. INTRODUCTIONGraphite (black lead or plumbago) is used in many industrial applications due to its high electrical and thermal conductivity, lubricity, and chemical inertness. High quality graphite can be used in metallurgy, molding, brake linings, batteries, and fuel cells. Graphite, composed exclusively of the element Carbon, is rather common mineral, but fine crystals are rare. Graphite is soft (hardness: 0.5-1 Mohs scale); has a layered, planar structure; occurs in platy or acicular (occasionally) morphology (Minerals.net; Pierson, 1993).USGS (2017) reported, global consumption of natural graphite continuing increase in the period of 2012-2016. In 2016, China used up 35% while produced 66% of the world’s graphite. Graphite mining are being developed in Madagascar, Mozambique, Namibia and Tanzania, but production reduced in Canada from 2015. Based on the statistic of Statista.com shows from 2011 to 2014 and a forecast to 2020, the global graphite demand is mostly in refractories, batteries, others, lubricant/crucible, foundry and pencil, and that is increase every year.Graphite Vietnam lies on the fault of the Red river from Yen Bai to Lao Cai, the reserves is estimated around 29.3 million ton and mostly in Lao Cai province where has Nam Thi graphite mine and Bao Ha graphite mine (MOIT, 2008). Vietnamese graphite products could reached to ~92% graphite carbon (Cg) (Tran Thi Hien et al., 2008). Studied samples was collected in Bao Ha graphite mine, is located in Lao Cai province. Graphite Bao Ha exists in two types as graphite flakes and amorphous (Hoang Thi Minh Thao et al., 2017)."

Jan 1, 2018

Most of the Ta-Nb ores in China occur in altered granites, and Ta-Nb minerals occur in these granites as accessory minerals. This type of Ta-Nb ores are characterised by whole mineralised granite mass, large reserves, low grade of tantalum and niobium, less economic minerals, complex mineralogy, difficulty in separation and concentration of Ta-Nb minerals and high operating cost of ore dressing. The Ta-Nb ore presented in this paper is a low-grade Ta-Nb ore occurring in altered granite in Jiangxi province. It has large reserves, with the grade of Ta2O5 0.013 per cent and Nb2O5 0.023 per cent. The process mineralogy study carried out by the authors determined ore mineralogy and ascertained occurrence of Nb and Ta and their mineral processing characteristics. The results are used as the guide for developing the optimum mineral processing flow sheet. The results also indicated that this type of Ta-Nb ore contains a high content of Li, K and Na, a low content of deleterious impurity Fe, and the tailings can be used as feed for glass and ceramic materials. This study provided important mineralogy information for exploiting and utilising low-grade Ta-Nb ore resources, developing a mineral processing flow sheet and further utilising the tailings.

Jan 1, 2008

By George M. Potter

Precious gold and silver markets support substantial activity in the search for and development of improved and unconventional ore and tailing processing methods. The need for such methods 1s strengthened by consideration of increasingly low grade and refractory ores and old tailing reserves. As background for this review of new and unconventional precious metal processing, recent USBM data (1981) show annual world gold production of about 40.8 million troy ounces. In the U.S. about half the 2.8 million ounce consumption was used for jewelry and the arts, 39 percent for industry, and 8 percent for dental purposes. World silver production in 1981 was about 365 million ounces. Domestic usage the same year was about 117 million ounces. More than $ was used for photography and 30 percent for electrical and electronics. By process, about 1 percent of U.S. production of gold came from amalgamation, 66 percent from cyanidation, 31 percent from smelting ores and concentrates, and 2 percent from placers. As for silver, about 11 percent is from cyanidation and 89 percent from smelting ores and concentrates. Evidently the search for innovative and unconventional precious metal processes must include gravity concentration, froth flotation, hydrometallurgical, and electrometallurgical methods. Although smelting processes are equally important, they largely comprise nonferrous metal technology, and are not discussed here.

Jan 1, 1984

By John F. Abel

In the debate between miners and ecologists, our industry has at last begun to get some of its story told. I have been told many times that it is hopeless to even try to get our side across. Some are sure that no one will believe us even when our cause is just. My reply would be that we have to tell the truth; again, again, and again. We will never convert a fanatic, but we must try to reach the reasonable and thinking people. I am encouraged because more of us are trying. Various mining companies here in Arizona have bought newspaper space to set forth some of the facts around our local environmental problems. The Arizona Mining Association co-sponsored a symposium in March: Mining and Ecology in the Arid Environment. The symposium program included tours arranged with local mining companies. The participants saw an acid plant, an acid leaching operation, an alluvial tailings dike, a tailings pond, a smelter, and a couple of open pit mines. This wouldn't phase you until you realized that half the visitors were ecologists, watershed and wild- life managers, and other assorted conservationists. It took a lot of guts. I am proud that we had that much confidence. As Pogo said, "We have met the enemy and they is us!" Actually, we met the enemy and they were just like us-concerned.

Jan 1, 1970

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By C. Barnett

"A description of the Geco orebody has been given by W .L. Brown and R.C.E. Bray (1). The mill flowsheet and equipment were described by M.J.S. Bennett, D. Wild and C. Lawton (2). Mill capacity is now 4, 150 tons per operating day of copper, silver, zinc and lead ore. A recent flowsheet has been published in the - Canadian Mining Manual (1966).Soon after the start of production in September 1957, it became apparent that large tonnages of sand would be required by the mine for backfill pruposes. Initial experimental work on the preparation of sand fill from the flotation tailings was begun in late 19 59. Cyclones of local manufacture, in a variety of sizes, were tested quite successfully. There were, however, several obvious advantages with some of the custom-built cyclones and a recommendation was obtained from the Techniquip Company. A single Krebs D-10-B cyclone was tested experimentally in 1960.INITIAL TESTWORKExperimental results showed that with our relatively coarse grind (in the order of 53 % minus 200 mesh) 75 - 80% of the flotation tailings could be recovered as backfill sand with one stage of treatment. Percolation rates of four inches per hour were obtained with cyclone inlet pressures in the range of 20 - 25 psi and feed densities of 20 - 23% solids."

Jan 1, 1968

By W. McDermott

It is well known that many so-called free-milling silver arcs are so classed more from their value necessitating a cheap process than from a real adaptability to raw amalgamation. Such low--grade ores, carrying more or less sulphurets, are more profitably treated by a cheap rapid process than by the more effective but costly process of roasting arid amalgamation. The tailings are sometimes crudely concentrated, or, after lying and becoming partially oxidized, are again worked in pans. Of late years, by the use of improved methods of concentration, many old low-grade tailings-piles have been reworked to a good profit; and in some improved mills arrangements are made to concentrate before or after amalgamation, thus making a single treatment in mill suffice. It is self-evident that on a low-grade ore a small increase in percentage saved is of no commercial advantage if accompanied by a material increase in cost, and therefore a cheap and continuous system of work is the real necessity, if a fair saving be effected. As an illustration of the possibilities of combined concentration and amalgamation on some ores, the following results of a working test at the New York Ore-Milling and Testing Works will be of some interest. The ore treated was a hard white quartz from Mexico, carrying a very small percentage of finely divided sulphurets, chiefly iron

Jan 1, 1885

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By George L. Heath

It may at first appear doubtful that any further ideas can now come from such a well-trodden soil, when we consider that the ground of the subject has been so thoroughly gone over in many of its phases and that observations have been recorded in technical journals, ever since the days when Luckow and his cotemporaries brought the electrolytic deposition of pure copper to the position of an exact scientific method. Certain facts, however, which seem worthy of note, have come under the writer's observation during an extended use of the method in a large refinery, involving frequent tests of refined Lake and electrolytic copper, and thousands of assays of native copper concentrates and tailings. This work has required a careful study of the conditions suited to the assay of refined copper, and of ores and tailings— conditions which must be varied for each particular case to secure the best results. Especially is this true when we come to the exact determination of pure copper in the high-grade refined metal of the present day. Very slight traces of impurities (especially tellurium, selenium, bismuth, tin, arsenic and antimony) seriously injure the properties of copper, notably its electrical conductivity. The increasing demands of electrical science and construction lead to the conclusion that the analysis of all high-grade American coppers, at least, has become, and must be in future (in or-

Jan 1, 1898

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

Mine closure is a legitimate element of the mining cycle and like mine development involves technical planning, permitting, and finally construction. Closure begins with the mine's operational footprint and transforms the site so that it meets the explicit requirements of the owners and regulators. Implicitly, the closure will increasingly need to meet the requirements of other interested parties such as the local community, workforce, and future land users. Golden Cross is the first modern mine closure in New Zealand. It operated for 6 + years as a mid-size gold and silver mine winning ore from both underground and open pit sources, and processing via a carbon in leach circuit including a cyanide recovery stage prior to tailings disposal. The mine is situated in a sensitive high rainfall environment, and is complicated by the existence of a large ancient landslide underlying most of the tailings dam and waste rock embankment. The regulatory process for mine closure in New Zealand is not clearly understood by operators or regulators alike. The Golden Cross mine was permitted under the Mining Act 1971 and closed primarily under the Resource Management Act. This switch of legislation, the parallel reorganisation of many government departments, and change in societal expectations with respect to long term environmental stewardship during the life of the mine resulted in the requirements of closure being significantly different to the expectations at permitting.

Jan 1, 1999

By Bothe C

Froth flotation processes use different surface properties of the minerals to be sorted. In an aqueous environment the hydrophobic mineral attaches selectively to air bubbles and is lifted to the surface of a separation vessel, while the tailings settle towards its bottom. Besides the surface properties, the hydrodynamic conditions play an important role. With respect to the hydrodynamics the flotation process can be divided, for simplicity, in two sub-processes. The attachment of hydrophobic particles to air bubbles, the so-called mineralisation, demands a large number of collisions and therefore high turbulences. The phase separation however needs a deterministic movement of both the particle-bubbles-aggregates and the tailings particles and therefore a quiescent flow field. The optimisation of the overall process requires a separation of both sub-processes, especially when fine particles have to be sorted. In conventional mechanically agitated flotation cells both sub-processes take place in the same turbulent volume. For this reason they suffer from a decreasing selectivity with decreasing particle size. In flotation columns the mineralisation of air bubbles and the phase separation are performed in a quiescent environment. This results in high concentrate grades and at the same time in a very slow attachment kinetics, which must, especially for fine particles, be counterbalanced by a long residence time of the slurry.

Jan 1, 1993

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Nord L. Gale

Lead, zinc, copper, silver, cadmium and many other heavy metals which are potentially hazardous if released into the environment in wastewater discharges have been of considerable concern to governmental agencies, industry and the general public. In response to this concern, an interdisciplinary research team at the University of Missouri has been funded by the National Science Foundation-RANN program to study trace contaminants associated with the production of lead for the past eight years. Seven modern mines in close proximity to two lead smelters in the forested Ozarks of Southeast Missouri are the largest source of lead in the world and in 1976 alone produced 504,095 short tons of lead, 82% of the United States total production. This new and rapid industrial development in a sparsely populated. rural forest region has offered a unique opportunity for studying the impact of trace metals and for developing improved techniques to control detrimental effects. Research on the wastewater discharges and two methods of biological and recycle control are discussed in this paper. Although the two mine-mill complexes investigated in this study have many similarities, the differences between the two are substantive and warrant separate examination.

Jan 1, 1977

By J. E. Garlanger

Each year, Florida mines approximately 40 million tons of phosphorite, most of which is ultimately converted to various commercial fertilizers. The phosphorite is mined from within the bottom portion of the 40-to 60-ft. thick surficial aquifer, using open pit mining techniques. The ore zone or "matrix" is generally overlain by relatively permeable fine sand to silty and slightly clayey fine sand. The ore itself is highly variable in nature but, in Central Florida, typically consists of less permeable clayey phosphatic sands and sandy clays with stringers of permeable sand. The ore is much more sandy in the north Florida mining area.

Jan 1, 1990

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967