Search Documents

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By C. J. Ferron

Gold occurrence in operating plant tailings ranges from gold in solution, fine free gold, gold associated with sulphides/arsenides/tellurides and gold occluded within iron oxides or arsenates and silica gangue. This paper briefly presents various alternatives to reprocess gold tailings, with examples. These include the use of centrifugal gravity separators, CIL, magnetic separation, flotation and pressure oxidation.

Jan 1, 1993

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982

By E Ferrow, R Herbert, M E. Malmstr, M Fuchs

The study of microbial sulfide oxidation and oxidation rates of tailings requires the use of sterile control samples in laboratory experiments for comparison purposes. The need for sterile tailings sand is also apparent in the study of microbial communities and processes. This study compares six different methods with regard to sterilisation efficiency and investigates chemical and mineralogical changes in the samples as the result of sample treatment. In addition, the effect of sterilisation on mineral weathering rates is also studied. The efficiency of the different methods with regard to sterility is estimated by most probable numbers (MPN) of both sulfur and iron oxidising bacteria. The sterilisation methods that were compared are: washing with sterile water, washing with ethanol, applying antibiotics, repeated heating to 70¦C, autoclaving, and γ-irradiation. There are several possible drawbacks with the different methods, including the risk of an applied chemical acting as a substrate for micro-organisms in the system, and the risk of altering the tailings. The results show a substantial difference in sterilisation efficiency between the treatments. For example, autoclaving, repeated heating, ethanol and irradiation efficiently kill micro-organisms, rendering an undetectable amount of bacteria after one month of incubation, whilst washing with water exhibits virtually no microbiological effect, with a bacterial content comparable to the control. The use of antibiotics for sterilisation ranks intermediate: the lag-phase was twice as long in the antibiotics treatment compared with the controls. X-ray diffraction, optical and electron microscopy, M÷ssbauer spectroscopy, and mineral magnetism indicate no significant change in the bulk mineralogical composition. However, X-ray photoelectron spectroscopy analyses show that with some of the treatments, sulfides are partially oxidised, as indicated by the formation of sulfate and partially û oxidised sulfur species at the tailings surfaces. Aerated batch weathering experiments performed on sterilised tailings samples and untreated controls indicated that while the initial rates of element (S, Fe, Cu, Zn, Mg, Na, K, Ca) release may differ between the samples, over the course of ~100 days of experiment at pH 2 and room temperature, the rates declined toward a similar value for all samples. To conclude, there does not appear to be one perfect method for tailings sterilisation. Autoclaving and heating damage the mineral grain structure and oxidise the sulfide surfaces. Ethanol, antibiotics and rinsing greatly alter the pore water chemistry through the washing procedure. In addition, ethanol and denatured antibiotics might serve as a substrate and also, in the case of antibiotics, adhere to mineral surfaces thus obstructing chemical reactions. Irradiation seems to be the preferable method on an overall basis, although the formation of surface Fe3+ was suggested by M÷ssbauer spectroscopy.

Jan 1, 2003

By R. W. Jigins

OPERATIONS of the Braden Copper Co. are in the Chilean Andes, southeast of Santiago. Most remote of the company communities is Sewell, a town of 12,000 people, 7000 ft above sea level at the junction of the Coya and Teniente rivers. Four miles down the Coya River is the smelter town of Caletones, elevation 4500 ft, with a population of about 3000. At the junction of the Coya and Cacha-poal rivers 24 miles below Sewell is Coya, elevation 2500 ft, location of the company's two hydroelectric plants. The principal accounting offices; steel, iron, and brass foundries; railroad shops; and major mechanical repair and fabricating shops are at Rancagua in the central Chilean valley, 44 miles from Sewell. The company owned narrow-gage railroad connects with the Chilean national railroad at Rancagua and above Coya is the only modern means of travel. El Teniente mine at Sewell is the largest underground copper mine in the world. The mill, at the portal of the main tunnel, has a capacity of 34,000 tons of crude ore daily, although production is lower during the winter beacause of electric power restrictions. When operating at capacity the mill produces 2000 tpd of copper concentrates and 32,000 tpd of tailings. Tonnage of tailings is equivalent to about 100,000 tons of pulp at normal water to solid ratio. Because the streams flowing from the Andes in the area of Braden's operations are used for irrigation, it is impossible to dump tailings directly to the river. The tailings pulp must be separated into solids and decanted clear water, and the clear water returned to the same water shed from which the original water was removed. Remaining sands and slime must be deposited in a reservoir where they will not cause trouble to farmers.

Jan 1, 1958

By E. A. Lawrence

The experiences of Canex Placer Ltd. in establishing vegetation on a lead-zinc tailing pond are presented, hoping others with similar challenges will be benefited. History The tailing ponds are the result of 23 years of mining and milling operations, which ceased in August 1970. Roughly 7.9 million tons of lead-zinc ore were removed in that time. The ponds are located between Salmo River and B.C. Highway 3, about 8 miles north of Nelway near the Canada-U.S. border.

Jan 1, 1975

By Dave Gilbert

The Antamina tailings beach is considered a fundamental design component, as well as a predictive control for phreatic surface control. In this sense, the paper point out the development and purpose of the tailings beach , as well as what future opportunities may exist. These present and future opportunities, include implications of the beach as an evaporative surface control thus reducing pond volume. These desireable outcomes include better control of the phreatic surface in a rockfill dam, and reduction of pond water volume.

Sep 21, 2013

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By G. J. Allen

Kennecott Copper Corporation's Nevada Mines Division initiated a program to stabilize the inactive portions of the tailings disposal area and perimeter dikes in 1946. To date, approximately 1,000 acres have been stabilized with vegetation and ground cover.

Jan 1, 1978

By Leggate J

In the past many coal mining projects commenced without any consideration being given to eventual site rehabilitation. Now that site rehabilitation is assuming greater importance with changing community expectations, and standards are becoming less negotiable, it cannot be ignored in either the development of mine working plans or economic models. The "unspecified" rehabilitation measures associated with many existing projects will be the subject of debate for some time to come yet. It would be wise to plan for the future. Once an agreeed standard of rehabilitation is accepted, good management involves considering practices which will facilitate eventual rehabilitation at least cost. Without planning for rehabilitation, many mines have adopted practices which are likely to result in very expensive rehabilitation measures and impact significantly on the overall profitability of the ventures. With adequate planning, procedures can be developed which achieve the same short term goals without significantly effecting cash flow but with very significant impacts on the final rehabilitation cost. This paper looks at the disposal of tailings and overburden in the coal mining process. The industry has in the past had an obvious preference for the "perceived" cheaper procedures for waste management such as wet disposal of tailings and high dumping of overburden. There are alternatives. The paper discusses the principles which should be incorporated into tailings and overburden disposal systems and identifies viable alternatives.

Jan 1, 1991

By M. M. Botz

Cyanidation tailings disposed of in a surface impoundment experience a loss of cyanide due to natural attenuation, which frequently reduces the cyanide concentration to very low levels. Quantifying cyanide losses in terms of impoundment geometry, local weather conditions and feed-solution chemistry has been largely empirical in spite of the fact that, in many cases, mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or below an effluent limitation. To permit a quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, weak acid dissociable (WAD) and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared with data collected for a North American tailings impoundment in 1998.

Jan 1, 2000

By S. Subbarayan, S. Chander, M. S. Klima

A laboratory study was conducted to investigate the potential for recovering anthracite from coal preparation-plant tailings. The study included washability analyses, cyclone simulations and froth flotation testing Samples were collected from either the tailings streams or the slurry ponds of five anthracite-cleaning plants. From each sample, a washability analysis was conducted on the 28x100 and 100x200-mesh fractions. Using the above data, along with published partition data, simulations were performed with various cyclone-staging arrangements for both water-only and dense-medium cyclones treating the 28x200-mesh fractions. Separate froth -flotation tests were conducted on the 28x100- and 100x200-mesh fractions from three of the plant samples. The washability, simulation and flotation results are presented as grade-yield curves.

Jan 1, 1996

Inpit tailings disposal has been undertaken at a number of mining sites within Australia. This paper presents a brief history of the experience of inpit tailings disposal at the Marymia Gold Operation in Western Australia, including geotechnical aspects of the design. Regular monitoring of the inpit tailings disposal into the K1SE Pit at Marymia has allowed the operators of the mine to assess the performance of the tailings storage against its predicted performance during the design phase. Results of this monitoring indicated that the predicted performance was exceeded and the results have been incorporated into the design of another large inpit tailings disposal, the K1 Pit. Monitoring of tailings disposal to both the K1SE Pit and K1 Pit has allowed the mine operator to make substantial savings from inpit tailings storage when compared with above ground tailings storage facilities. The inpit method of tailings disposal at Marymia has proven to be acceptable from an environmental perspective by reducing the water resource requirements of the project, backfilling pits, which would otherwise collapse with time and eliminating the need for disturbing additional areas of mining leases, which usually accompanies construction of above ground tailings storage facilities.

Jan 1, 1999

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By Joe Hudson

The successful heap leaching of tailings as illustrated in the two photographs below, requires special provision. These will be enumerated in the presentation. The two illustrations show the project as it evolved. Note the bermed pads and the conveyor materials handling system which provides for agglomeration of the feed material.

Jan 1, 1998

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By F. Liu, S. Rezaei, M. Muinonen, M. Barati, V. L. Lakshmanan, S. Marcuson

Canadian nickel-copper ore deposits have been a major source of nickel, copper, cobalt and precious metals for more than 100 years. The two main minerals of interest, pentlandite (Pn, (Ni,Fe)9S8) and chalcopyrite (Cp, CuFeS2), are usually accompanied by large quantities of pyrrhotite (Po, Fe1-xS). Until the 1950s, Po containing small amounts of nickel was routinely smelted as part of the valuable Ni concentrate. The rapid growth in Ni demand following the Second World War created impetus to treat the Po separately. This action would liberate a valuable smelting capacity for higher value Pn, allow for recovery of Ni locked in Po, convert the Fe to iron oxide or metallic iron pellets, and recover S as sulphuric acid or elemental sulphur. The roasting process also has the potential to produce energy due to the highly exothermic oxidation of Po. The Ni industry would then have a “waste-free” process. Both Inco (now Vale) and Falconbridge (now Glencore) developed processes and built large industrial plants for this purpose that operated with some success. But technical issues and tenuous economics were continual challenges. By the early 1980s these industrial operations were closed. Sophisticated froth flotation methods of rejecting Po were developed, and Po containing up to 1% Ni became a waste material reporting to the tailings stream. As part of a major study on possible processing methods of Po for both value recovery and waste remediation, this paper presents a historical perspective on Canadian Po tailings with regards to their generation, inventory, value, and attempts to process them.

Jan 1, 2017

By B. W. Brooks

"After an extensive period of University research and field trials, large scale reclamation of the Waite Amulet tailings discharge areas commenced in the spring of 1978. The Noranda program consists principally of sampling the complete dam to determine the vegetation potential of the various areas, addition of the required amelioration materials, and the use of good agricultural practices. This paper describes the development work that led to the establishment of the Noranda-Guelph Contract and the subsequent findings concerning the revegetation of tailings dams. Current revegetation procedures are presented. INTRODUCTIONThe Amulet Mine Ltd. was staked in 1924 and by 1930 had constructed a small 300 ton per day flotation plant. During the late twenties and early thirties, Noranda Mines Ltd. increased its equity in the company to gain a sixty percent share of this small mine. In 1933 the mine was amalgamated with another small producer, the Waite Ackerman Montgomery Mine Ltd., which was more than eighty per cent controlled by Noranda to form the Waite Amulet Mines Ltd.An interesting historical side point to the story of the Waite Ackerman Montgomery property is that a concentrator was never constructed. In fact, the first ore to go through the Horne mill of Noranda Mines Ltd., built in 1928, was not from the famous upper H and L ore bodies but custom shipments from the Waite."

Jan 1, 1981

By Allen H. Gipson

Innovative thinking has led to the development of safe, environmentally sound, and cost effective methods for expanding existing tailings storage facilities (TSF). Three case histories are discussed here to demonstrate methods that have recently been used or are being considered for such expansions. Maintaining the integrity of the structure and reducing costs were primary goals in each case.

Jan 1, 1997

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014