Search Documents

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed'-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,'~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

By Robert Anderson

The diffraction of x-rays by cold-worked and heavily polished surfaces of metals gives, no evidence of an amorphous state and typically perfect crystallographic diffraction' patterns are obtained. Severely cold-worked metals, reduced as much as 98 per cent. in area, give true crystallographic diffraction patterns, and polished surfaces of large single crystals of metal give typical crystallographic patterns. The conclusion is drawn, on basis of x-ray evidence, that metals are fragmented on cold work and polishing and not amorphized. THE purpose of this paper is to report evidence, regarding, metal: structures, that is contradictory to the amorphous-metal, hypothesis of Beilby, and particularly evidence that is opposed to the proposition that a vitreous amorphous layer is produced by polishing a piece of metal. According to the theory of Beilby, which has been developed, by Rosenhain and others, polishing a piece of metal greatly affects the condition of the metal at or near the surface polished, making that surface entirely different in character from the metal beneath. A vitreous amorphous surface film is said to be formed. The polishing process, on the basis of Beilby's explanation, is well known-and does not' require discussion here, but it is advisable to seek the precise meaning of,., the term "amorphous." According to Beilby, "amorphous means. Non-crystalline in the most intimate sense of the word'; the molecules are not marshalled in crystalline order and orientation." According to Rosenhain, the amorphous condition is that assumed by a metal when, the .crystalline arrangement is completely broken up so that the atoms exist in a state of disorderly arrangement similar to that ;which exists in the liquid state. Thus, from the point of view of the phase rule, the "amorphous phase" is regarded as being identical with the liquid phase. Amorphous metal is often likened to an undercooled liquid. A crystalline substance is one in which the atoms are arranged in space according to some definite repeating geometrical pattern. The existence of amorphous metal has not been definitely proved.

Jan 1, 1925

Jan 1, 1949

By Compiled by Staff

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and· approved February 25, 1913, made it the province, and duty of the Bureau of Mines to ""disseminate· information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue of the Bureau of Mines List of Publications and Articles describes reports and articles published during the period January 1, 1990, to December 31,1991. It, supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;2 and the 5-year lists of publications and articles from January 1, 1960, to December 31, 1964,3from January 1, 1965, to December 31, 1969,4 from January 1, 1970, to December 31, 1974,5 from January 1, 1975, to December 31,1979,6 from January 1, 1980, to December 31, 1984,7 and from January 1, 1985, to December 31, 1989.8"

Jan 1, 1992

By T. Mason, R. Macko

Electroless nickel (EN) coatings are widely used in the manufacture of automotive parts, providing uniform coating, corrosion protection, wear resistance and lubrication. In contrast to EN plating benefits, the disposal and treatment of waste solutions can cause many difficulties. The use of electrochemical treatment technology greatly improves _the operation of the main wastewater treatment process and reduces operation costs. A new, state-of-the-art job shop in the Chicago area, which provides EN plating for the automotive industry, has installed a large separated electrolytic cell for the treatment of spent EN solution (from dumps and wastewater). The waste/wastewater is handled by the separated electrolytic cell, batch treatment system, filter press and neutralization station. The implementation of modem electrolytic technology and auxilliary equipment provides an effective waste treatment process that meets environmental compliance criteria.

Jan 1, 2000

By C. C. Harris

A critical literature review leads to a descriptive model of tumbling mill operation based upon energy partition concepts and the necessary requirements for particle fracture. As grinding proceeds into the ultra-fine region, conditions which are of little significance during normal operations gradually become controlling. These involve increasing resistance to fracture and an increasing tendency to aggregate as particles become smaller, and a growing fraction of the power input being consumed fruitlessly. The result is that fineness asymptotes to a maximum value as comminution proceeds indefinitely; thus where t is time, p and n are experimentally determined parameters, and Ø is a measure of fineness, which is presumed to be proportional to specific surface area, or proportional to the reciprocal of the size modulus (provided that the distribution modulus remains constant with time), or both. Ø, is the asymptotic value of Ø and is a measure of the grind limit. A method for its graphical determination is given. In a previous paper1 the physical and mathematical principles requisite to a study of the role of energy in comminution were reviewed. The micro-process of comminution — or the comminution event — can be investigated in terms of (a) the magnitude of the force-field localized around the individual particles which gives rise to the stresses generated in the particles, which in turn induces their fracture, and (b) the distribution of fragment sizes, should the event prove fruitful. The entire fragmentation operation can be considered to be the totality of its individual events, and in order to obtain a single independent variable of the process it is necessary to transform and sum the local stresses in terms of energy.1 This energy, however, will account for only a fraction of the energy input to the comminution process, the actual magnitude depending upon the kind of mill and several related factors. From the comminution viewpoint the primary function of a mill is that of stressing as many as possible of the individual particles of the charge to failure, with the maximum economy of energy expenditure. This is difficult indeed to achieve, for stressing a particle does not always break it, while the overwhelming portion of the energy input is involved with various internal mill processes which — almost incidentally — determine the magnitude, frequency, and manner in which the forces are applied to the particles. Essentially, these processes depend upon the mill dimensions, loading and speed, and they may be little affected whether fracture occurs or not. These processes must be delineated if a complete description of the role of energy in comminution is to be given; the energy account sheet1 (Fig. 1) in showing how the energy is partitioned for the requirements of the several functions it performs, provides a framework for the development of a model of the comminution process. Actual numerical values for the variables appearing in Fig. 1 will depend upon the mill, materials, and operating conditions. A possible general relationship between the variables will be suggested in this paper. Before proceeding further, a cautionary note must be issued. It was pointed out in an earlier paper' that while energy input is not changed by increasing the power and decreasing the time in the same proportion, and vice versa, the results of the process in terms of particle fineness may be different. Thus, although energy is chosen as the independent variable of a comminution process, it is not absolutely independent, and care must be exercised to ensure that it is used within its range of valid application. Time has the necessary independence, and it will be used in place of energy where it is appropriate. The residence time in a mill is usually of the order of minutes. Under these conditions the particles are subjected to "... a relatively constant fracture producing environment".2 However, under the more rigorous conditions of greatly extended time, which pertain in ultra-fine grinding, indications are that the fracture producing environment no longer remains constant; this is the major subject of this paper. At this extreme limit the mill is probably taxed to its utmost, and at the same time the bulk material properties are becoming closer to ideal, while the physico chemical effects associated with surfaces, edges and corners are multiplying. (The edge length per unit volume is proportional to the square of the specific

Jan 1, 1968

By A. B. Cox, L. W. Wark

In an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solution composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents—namely, sodium cyanide—on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electrolytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60". There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1935

By Stanley Herold

As an accompaniment to the interesting papers which discuss the practical aspects of forced drive, or flooding, in our oil fields, and to others which deal with laboratory or field tests on the same subject, a few remarks on the theoretical principles concerned may not be considered inappropriate at the present time. Without claiming to have had the field experience which some of you certainly possess I venture to present some of the results of an analytical investigation upon this method of increasing the recovery of oil from our natural reservoirs. I firmly believe that these results will accord with your experience. I shall confine the present discussion to the consideration of a perfectly ideal situation Let us assume that the productive formation lies perfectly horizontal, that it is of uniform thickness, of perfectly homogeneous texture, and that it contains oil with gas in solution, and no water, throughout a definite, although undefined, lateral extent. We shall furthermore assume that the pressure existing within the reservoir as thus specified, is such that some of the gas is in the free state, spread uniformly throughout, in the form of minute bubbles within the pores of the formation. We now have an ideal reservoir subject to the peculiar action of capillarity as described by the French physicist Jules Jamin. In all directions within the reservoir we see these bubbles of gas, separated by globules of oil which tend to remain in the capillary channels that connect the pores. The action of these bubbles and globules under the application or release of pressure has been fully described by Jamin.1 Most of our oil fields in the Mid-Continent and Eastern districts are subject to this action of capillarity: The fact that the actual reservoir is often far from being ideal in the manner specified above does not preclude the, influence of this phenomenon. The oil, existing under a pressure exerted by the compressed gas, is securely locked in place

Jan 11, 1926

With the evolution rate of technologies, earthmoving equipment users are establishing vision statements for their operation out to and in some cases beyond 2000. Autonomous systems are receiving a lot of 'press' - and rightly so, as they hold a potential for achieving quantum leaps in productivity and cost gains. Caterpillar feels that it is important that the infrastructure of on-board systems are understood and can be utilised more in the near term to `grow' a user up to the stage of autonomous operation.

Jan 1, 1997

By Ivo Dreiseitl, Kondratenko. Anatoly

"The second prime area within the Interoceanmetal Joint Organization exploration area named H22 was delineated in 2013 with the goal to ensure sufficient nodule reserves for profitable mining operations and processing.The knowledge base for area H22 has been obtained from archive materials. The geological situation can be characterized as follows: the sea bottom is represented by tectonic blocks oriented in a sub-meridional direction. According to swath mapping, the depressions (troughs) are contoured at depths of 4500-4600 m while the tops of horsts occur at 4300-4350 m. Volcanic relief occupies 6% of the H22 area; in the eastern part a multicone volcano was detected. Its area at the base is 153 km2. The maximum height of a cone above the base is 850 m. The crystalline basement composed by tholeiitic basalts of late Oligocene age is covered by about 100 m of sediments. Semi-consolidated to consolidated calcareous nanofossil sediments of the Marquesas formation are deposited on the basement. Higher up in the profile sediments of the Clipperton formation occur. They are represented by unconsolidated siliceous (Radiolaria, Diatom) ooze. Sediments containing calcium carbonate have not been detected. Where opaline silica (or CaCO3 if any) content is below 5%, the sediments belong to zeolitic clays or red pelagic clays. Grain size composition of the seabed and the near-seabed sediments in H22 classifies them into clayey silts."

Sep 1, 2014

By Robert H. Peters

This Bureau of Mines report describes several significant problems associated with absenteeism among underground coal miners. The vast empirical literature on employee absenteeism is reviewed, and a conceptual model of the factors that cause absenteeism among miners is presented. Portions of this model were empirically tested by performing correlational and multiple regression analyses on data collected from a group of 64 underground coal miners. The results of these tests are presented and discussed.

Jan 1, 1987

[ ]

Jan 1, 1907

The first session of the Rocky Mountain Coal Mining Institute was called to order by Past President R. M. von Storch, who introduced the President, R. R. Williams, Jr., Manager of Mines, The Colorado Fuel & Iron Corporation, Pueblo, Colorado. His speech of welcome is as follows: "Members and guests of the Rocky Mountain Coal Mining Institute: It is my distinct privilege to welcome you to the fifty-fifth regular meeting of the Institute. We have again gathered to meet our treasured friends, to make new acquaintances, to hear important papers by outstanding authorities, and to generally enjoy ourselves in the setting of the beautiful city of Colorado Springs. It is the prerogative of your President to appear as optimistic as he desires in the opening remarks to this Institute. I must admit that I have had to cast aside some bare and significant facts to the contrary. However, there must be a great deal of optimism present in an industry that can survive the adversities that have confronted. the coal industry within recent years.

Jan 1, 1959

By Usko Anttikoski

This article deals with the extensive geotechnical soil and bedrock mapping system maintained in the Geotechnical Office of the City of Helsinki since 1955.Soil maps have been prepared to scales of 1:500,1:2000 and 1:10 000, and most recently in 1978 a new type of bedrock map was printed to a scale of 1:10 000, which covers the whole city area and particularly serves rock tunnel construction. A map showing the types of foundation building in the central city area, which will also serve underground construction activities, is currently being prepared. Since the geotechnical mapping system has been well received in Helsinki and the drawing of similar maps has also been undertaken in other Finnish towns, this mapping method is believed to be of interest to foundation engineers and tunnel constructors elsewhere too. THE GEOTECHNICAL CONDITIONS IN HELSINKI The geological structure of Helsinki, and of all Finland, presents two types clearly differing in character and age; bedrock and soil. The solid bedrock is Precambrian, while the soil dates from the Pleistocene Age and has mainly been deposited during and after the Ice Age. Thus the history of Helsinki only displays very old and very young formations, but nothing in between. The ground level in Helsinki is +62 at its highest and the sea bottom close to shore is -15 at its deepest. The deepest rockhead has been found to lie at the -70 level.

Jan 1, 1979

By Gordon R. Haworth

Conditions affecting minerals investments are continuing to change at an increasing rate, and in this paper we will attempt to predict the course of mine financing in the future. We will first review the situation historically and then examine the problems and constraints that are now making the financing task more difficult. Suggested solutions are discussed, and a new method of financing a group of mining projects is hypothesized.

Jan 1, 1977

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By Paul E. Blackburn, Joan B. Berkowitz-Mattuck, Edward J. Felten

The oxidation behavior of MOSi2 has been studied between 450° and 650°C, the temperature region where "pesling" occurs. Disintegration ("pest-ing") of MoSi2 is shown to occur in the presence of oxygen, but not nitrogen, carbon dioxide, carbon monoxide. or argon. The rate of disintegration is extremely sensitive to oxygen pressure. The crack density of polycrystalline MoSi2 increases ivith lime at temperature. All kinds of cracks are observed: THE excellent oxidation resistance of MoSi, at temperatures of 1000 to 1700°C promises to have important technological benefits. However. the ap- Ihose which are confined within a single grain, those that ci'oss grain boundaries transversely, and those that follow grain boundaries. Laue photographs verify the existence of Iranscryslalline cleavage. Single crystals of MOSi2 do not "pest". Tlrcd solrlbility of oxygen in MoSi2 is extremely low, no lattice changes being observed as a result of exposure of MoSi2 to oxygen in the "pest" temperature range. plicability of MoSi2 is somewhat restricted by the occurrence of a completely destructive oxidation of the intermetallic phase at intermediate temperatures (300" to 6003C). This phenomena was ternled to be the "MoSi2 pest" by Fitzer who first observed it.' Molybdenum disilicide is a metallic material in both physical appearance and electrical properties.

Jan 1, 1965

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019