Search Documents

By Das A. K

Investigations were carried out to understand the effect of liquid viscosity (u = 1 x 10-3 - 5 x 10-' Ns/m2) on the size of primary bubbles formed at high gas injection rates (Q = 100 - 1000 cc/s, U = 0.04 - 0.42 mach) under room temperature conditions using flush tuyere (3 mm diameter) operating vertically upward. Tuyere pressure fluctuations were correlated to the mode of bubble formation by simultaneously filming the bubble and the corresponding tuyere pressure fluctuations displayed on an oscilloscope screen. A simple mathematical treatment is presented to estimate bubble size in viscous liquids. The theoretical results are compared with the experimental measurements.

Jan 1, 1987

By K. Vanstaen, K. M. Cooper, S. Ware, S. L. Boyd

Remediation and restoration of offshore marine habitats is a relatively new concept with attempts in European regions largely being instigated by requirements of various strategic directives including Article 2 of the Habitats Directive (1992), the EC Water Framework Directive (2000, Article 2 of the OSPAR Convention (1992) and the developing European Marine Strategy Directive. A field experiment to establish the practicality of various options for rehabilitating the seabed on the cessation of dredging has been successfully set up. The purpose of this experiment is to investigate the practicality and effectiveness of gravel seeding as a potential restorative method that can be applied at marine aggregate extraction sites following cessation of dredging. Zone 2, within Area 408 (offshore Humber) was chosen as the experimental site as there is some evidence for persistence of sand which may have resulted from screening operations at this site.

By Adrian Smith

14.1 INTRODUCTION From the time the last recoverable gold is extracted from ore on a heap leach, the ore - now spent ore - changes from being the resource, indeed the raison d'etre of the operator, to a potential liability. The spent ore contains process chemicals and constituents leached from the ore both in the interstitial pore water in the heap and on the surfaces of spent ore. If these chemical species were released to the environment, it could have a potential impact on the quality of both surface water and groundwater resources. Accordingly, the spent ore must be left in a condition where it does not present a potential environmental liability. This can be accomplished either on a decommissioned pad or, if the heap leach is operated as a load/unload scheme, in a waste facility. In general, the residual cyanide level in the spent ore is the perceived controlling factor when determining whether the leached material is suitable for abandonment. Regulatory authorities set permit conditions for heap leach abandonment in terms of residual cyanide levels, for example, Smith and Struhsacker (1987). This chapter discusses cyanide degradation and methods for detoxifying a heap leach in order to meet regulatory limits/permit conditions for abandonment. Cyanide degradation and detoxification by "natural" processes are described initially, based on the chemistry and geochemistry discussed in Chapter 13. This leads to a review of chemical treatment processes for detoxification of spent ore. The advantages and apparent disadvantages are then appraised. 14.2 NATURAL DEGRADATION AND DETOXIFICATION For the purposes of discussion, "natural" detoxification processes can be divided into two alternatives: • Passive abandonment (the so-called "do nothing" option); and • Water In the first alternative, the spent ore is merely left on the leach pad to age; the second alternative involves the flushing of the spent ore with water.

Jan 1, 1988

By J. R. Wynnyckyj, R. Marr

Continuous measurement based on radiation pyrometry has often met with difficulties whose causes have been obscure. In this paper the experience gained with on-line pyrometry in utility and Kraft recovery boilers in the range 800-l400oC will be reported. It is shown that the inherent problems are best resolved by using a spectral pyrometer not sensitive to gas radiation. The radiation from the suspended particles thus provides the signal. It is further shown that the principle cause of difficulties is signal calibration drift caused by heat fluxes originating from surrounding surfaces and reflected by the particles to the pyrometer. Several examples are given how such problems may be resolved using process information and/or additional measurements, fed to and processed by and on-line microcomputer.

Jan 1, 1989

By W. C. Clark, J. B. Schloen

Two papers have been written, previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,Z published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 ox. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidiae-roasted at 700' F. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent HzSOa), filtered and charged directly to the dor6 furnace for refining to dore metal. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1944

By Simon D. Handelsman, Malcolm Scoble, Marcello Veiga

"Abstract - In many mining areas, potentially profitable mineral projects can be at risk because local people do not trust their governments and mining companies on many issues, including human rights. Projects will continue to be vulnerable to potential failure, delays, and higher costs. This paper suggests that geoscientists need to be aware of the global challenges they face from issues of corporate social responsibility, sustainable development, and human rights. These are not areas in which geoscience education has traditionally focused.This paper examines the types of conflict concerning human rights that are encountered by geoscientists involved in mineral exploration and development. It provides a background to human rights issues and presents a classification of the types of issue encountered. It reports on a survey of case studies that provide examples of the breadth, complexities, and consequences of such issues. The paper then concludes by outlining the development of codes and standards to improve performance, and suggests approaches for positive, practical engagement."

Jan 1, 2003

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By J. J. Denny

IN a preliminary paper (1) it was shown that the addition of small quantities of metallic aluminium powder almost completely inhibited the solubility of siliceous material in the beaker. Six rabbits exposed to quartz dust for six months all showed well developed silicosis. Seven rabbits exposed to quartz dust plus 1 per cent metallic aluminium powder for the same period did not develop silicosis. At that time, we were not in a position to state either the manner in which metallic aluminium reduced the solubility of siliceous material, or, from the animal experiments, whether the aluminium was acting locally or systemically, or for what period after the cessation of dusting it would continue to act. This paper reports the further progress of this investigation. CHEMICAL EXPERIMENTATION The technical details pertaining to the various substances used in the experiments are given in an appendix which is on deposit with the American Documentation Institute, Washington, D.C. For lack of space, it is not printed here. The term 'solubility' is used to indicate the concentration of silica in the solution under the conditions as noted, determined colorimetrically (2), and expressed as parts per million (p.p.m.). The term 'reduction in solubility' indicates the difference between the solubility of the .silica in the presence of the aluminium powder and its solubility in the absence of aluminium powder. It will be noted that the solubility figures for different samples of quartz with no added aluminium vary considerably. The figures do not refer to an equilibrium solubility of silica but to the actual amount of silica dissolved from a given sample in a given time at a given temperature. In view of the fact that quartz dissolves extremely slowly, it is evident that the actual figures in any case will depend upon the surface exposed, i.e., fineness of grinding of the different samples.

Jan 1, 1939

By T. T. Nguyen, D. R. Gunasegaram, D. Celentano

"Heat transfer rates at the casting-mold interface are believed to be substantially reduced by the formation of an interfacial gap during the course of solidification of aluminum alloys in permanent molds. In the current work, the effect of force-cooling a permanent composite mold on (i) the initiation and growth characteristics of the gap and (ii) interfacial heat transfer rates are studied. Interesting comparisons are made with the case where no cooling is employed. Casting and mold displacements are measured using L VDTs, and the mold is force-cooled by air jets.IntroductionIn a gravity casting situation where an aluminum alloy solidifies in a permanent mold, a gap initiates and grows between the shrinking casting and the expanding mold (1). It is widely believed that the formation of this gap, customarily referred to as an 'air gap', results in a substantial reduction in the heat transfer coefficient at the casting-mold interface (2), and hence is an important factor in solidification studies.The nature of the air gap formation process is thermo-mechanical. The rate of heat loss from the casting first determines the rate of solidification, which, in turn, decides when the gap initiates. The reason for this is the requirement for the solidified casting surface 'skin' to gain sufficient thickness, and hence strength, to be self-supporting. Once the gap initiates, the gap width controls the rate of heat loss from the casting, which, again, determines the rate at which the gap expands."

Jan 1, 1997

By W. L. Zeigler

The gravity concentrator of the Heela Mining Co. was originally constructed in 1888 by the Milwaukee Mining Co., which was operating the Gem of the Mountains mine. It was purchased by the Hecla Mining Co. in 1900, and placed in operation 2 years later. At that time the capacity was only about 200 tons a day, but many additions and changes in equipment have been made so that the present capacity is about 800 tons. One of the outstanding improvements made was the substitution of Callow flotation cells for vanners, which occurred in 1915. The recent building of a flotation plant for treating jig tailings, and the construction of a modern surface plant at the mine, following the

Jan 1, 1928

Domestic: Middle West-,11.. B. Newcombe Eastern District-J. French Robinson1 Kansas-Henry A. Ley 2 Oklahoma-Henry A. Ley 3 Texas, except Gulf Coast and Panhandle-M. G. Cheney 5 Texas Panhandle-W. E. Hubbard and H. E. Crum 6 Gulf Coast-L. P. Teas 7 South Arkansas, North Louisiana and Mississippi-H. K. Shearer 8 Foreign Mexico-V. R. Garfias and C. 0. Isakson 9 Canada-Line M. Farish 10 Venezuela-C. W. Hamilton 10 Colombia-J. T. Duce 12 Peru-O. B. Hopkins 12 Trindad-Williaim J. Millard 13 Dutch East Indies-Fred B. Ely 13 Rumania-I. I. Gardescu . .. . 14 India-Eric J. Bradshaw 14

Jan 1, 1931

By C. Allen

A series of zinc chloride electrowinning tests was carried out in a laboratory scale cell to evaluate the effect of temperature, current density, electrolyte composition, gas sparging and additives on the performance of the cell with respect to current efficiency, voltage, specific energy consumption and deposit morphology. The anode material was DSA for chlorine evolution and the cathode was made of aluminum. At 400 A/m2 current density, a current efficiency of 90.9%, a voltage of 3.4 V and an energy consumption of 2.78 kWh/kg were observed. Air sparging was found beneficial but was not pursued for health and safety reasons. Various additives in the same chemical family as tetrabutyl ammonium chloride (TBAC1) were tested. Both TBAC1 and tetrabutyl ammonium bromide were found to be equally effective. Attempts to carry out the electrolysis at 1200 A/m2 were not as successful.

Jan 1, 2000

By Peter W. Scott

The Caribbean islands, with their very diverse geology, are a source of several industrial minerals both for their own domestic consumption and for export. The geology of the Greater Antilles, which comprises Cuba, Hispaniola, Puerto Rico, and Jamaica has a Mesozoic or pre-Mesozoic basement overlain by sediments and volcanics, the latter being dominantly island arc in character. Later granitoid intrusions were emplaced. Obduction of ophiolites also occurred variously from the mid- Cretaceous to the Palaeogene. Thick accumulations of limestones surround the older strata, along with Neogene and younger sediments. The Lesser Antilles islands form an arcuate chain, mainly of volcanic rocks of calc-alkali or sub-alkaline affinity with some younger limestones and siliciclastic sediments. Trinidad and Tobago have closer similarities with the South American continent in their geology. Tobago has a metamorphic complex, juxtaposed with a volcanic-plutonic complex, and limestones. Trinidad has very thick Cretaceous to Recent exposed sedimentary sequence. The current exploitation of industrial minerals in the Caribbean is dominated by construction raw materials (mainly sand and gravel, limestone, and cement), although there is extraction of gypsum, silica sand, marble, clay (almost entirely for construction use), pumice, and natural asphalt. Salt is obtained from solar evaporation of seawater. Limestone of high purity and high brightness, gypsum, pumice, and high-density igneous rock have potential for further development of their markets, particularly ex- ports. Potential new and undeveloped industrial-mineral resources include residual and sedimentary kaolin, bentonite, zeolites, magnesite, and talc. Cuba could be a source for many industrial minerals in the future.

Jan 1, 1999

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By Minna Päällysaho

For the first time, the idea of sustainable development was recognised at a high political level at the UN Conference on Environment and Development held in Rio de Janeiro in 1992 (UNEP, 1992). Then the governments of the world committed themselves to promote sustainable development in their national activities and international co-operation. In 2001, the European Council approved the EU Strategy for Sustainable Development (European commission, 2011). This complements and supports the EU?s so-called Lisbon Strategy (European council, 2000) on competitiveness. The revised Strategy for Sustainable Development was approved in June 2006. Recently sustainability has had an important role in policy and decision-making while the public awareness towards limits of the environment has been rising. However, the indicators of industrial sustainability satisfy primarily the needs of corporate management and global investors. The information is often broad and non-specific and might occasionally even give a false impression. Moreover, contradictions between environmental, economical and social aspects also point out the unreliability of existing sustainability indexes. Therefore, the current state of affairs serves the interests of neither the industry nor the policy makers. Current corporate sustainability indexes and indicator systems need to be assessed with scientific methods encompassing the identification of their strengths and weaknesses. This requires quantitative and qualitative assessment and synthesis of existing indexes and indicator systems, providing new data on the functionality of existing corporate sustainability indicators. Therefore, the assessment lays the foundation for the development of new, more balanced sustainability index. Our first aim in this multidisciplinary article is to analyse existing global sustainability indexes for process industry. Second, we will introduce a first version of a new sustainability index for process industry, which includes the environmental, social and economic impacts of the plant, as well as legislation aspects.

Sep 1, 2012

By H. Siebel, N. A. D. Parlee

MIZIKAR, Grace, and parlee' studied rates of absorption of oxygen in stagnant liquid silver in a new type of open-ended gas-liquid metal diffusion cell, where the capillary diameters used were 1.5, 2, and 3 mm. They reported that the rates appeared to be controlled by the rate of diffusion of oxygen atoms in liquid silver and they used their data to arrive at the following equation as a reasonably good representation of the diffusivity (D) of oxygen in liquid silver: D = (14.7)10-4 exp (-7100 ± 3200)/RT cm2/sec Since this type of diffusion cell offers a promising method of measuring diffusivities of gas atoms in liquid metals, the senior author of this note and his students are carrying on a critical examination of the method, and are attempting to improve and extend the technique. The research reported briefly here was designed to examine more carefully the earlier conclusion1 that the absorption rate is diffusion-controlled, and to find out whether the diameter of the cell could be greatly increased and thus extend the method to systems where gas solubilities and diffusion rates are much smaller than in the case of oxygen in silver. For the purpose of these experiments, the open-ended capillary cell used by Mizikar, Grace, and Parlee was replaced by a small cylindrical crucible (1 to 1.7 cm in diam) containing pure silver (to a depth of 1.3 to 3 cm) resting in the bottom of a closed-ended vertical quartz tube, with an evacuated quartz filler tube just above the crucible to reduce dead volume. The method of measuring the rate of absorption was otherwise very similar to that of Mizikar, Grace, and Parlee and all the same precautions were taken. A much smaller and shorter tube furnace was used for heating, but simi- lar precautions about temperature gradients were observed. This technique was nothing more than the application of a Sieverts apparatus to the measurement of rates of absorption in small crucibles of stagnant liquid silver. In each run the volume of gas absorbed (V) was plotted against the square root of time (vt) and apparent diffusivities were calculated from the slope of the line, as described by Mizikar, Grace, and parlee.' Care was taken to use only the data obtained during the early part of the total absorption period while the cell functioned as one of infinite depth. The results at 1000°C are summarized in Table I and Fig. 1. The following conclusions may be drawn: 1) Diffusion cells up to 1.7 cm in diam yield, within experimental error, the same values for the diffusivity of oxygen (D) as the capillary cells of 1.5, 2, and 3 mm in diam employed by Mizikar, Grace, and Parlee. Cell diameters as large as 1.7 cm are probably not desirable for the most precise work. Intermediate sizes, perhaps 0.5 cm, will be most practical. 2) All absorptions measured were consistent with a model where the rate is controlled by the diffusion of gas atoms in the metal. The fact that runs at absorption pressures ranging from 0.1 to 1 atm (at any one temperature) give

Jan 1, 1965

By P. Barnes

SEVERAL interesting and important considerations may be based upon an analysis of the cost of producing Bessemer rails, and the facts thus set forth may be much more clearly emphasized by reducing each item of cost to its own fractional proportion of the sum total in each branch of the manufacture. The estimate given below is not absolutely complete in minuteness of detail, but it may be fairly taken as a basis for the suggestions to be noted : Perhaps the most striking comments that can be made upon this statement are those arising from a consideration of some of the smaller items, and even the least of these quite loses its insignifi¬cance when its proportion of the whole is expressed in actual money, as for the work of a year, or even for a single day. Thus, if the item A 5 be considered, the importance can be clearly

Jan 1, 1877

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By Jim Bruce, Peggy Hagerty Duffy, Mary Ellen Large, Allen Cadden

"Over the past 40 years, Deep Foundations Institute (DFI) has executed its mission “to bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and consensus voice for continual advancement in the deep foundations industry”. Like DFI, micropile technology began a significant growth path in the mid-1980s. This paper highlights how DFI’s mission was executed in the deployment and expansion of micropile technology.INTRODUCTIONMicropiles are small diameter foundation elements constructed using specialty drilling and grouting methods. Micropiles have evolved since their introduction into the North American market in the 1970s from being lightly loaded (less than 30 kips) elements used primarily for remedial applications, to today’s high-capacity, often hybridized foundation systems, for both remedial and new-build projects. Micropiles now occupy a substantial market segment in North America.For 40 years, DFI has aimed to be the forum for discussion of all issues related to deep foundations design and construction. DFI now supports 21 technical committees and working groups on all deep foundations technologies and has expanded to include regional chapters in Europe, India and the Middle East.Several key steps are required for the successful execution of DFI’s mission, including identifying a need, engaging dedicated and knowledgeable people, developing effective vehicles and resources for information sharing, cultivating stakeholder contributions and advancements, stimulating influence/impact on deep foundations market, and expanding approaches to continue progress. Pile drivers in New York City (the original organizers of DFI) positively affected their market using these same steps: they recognized a specific need, gathered the people who could affect change, convened a discussion forum (which is common today, but was innovative at the time), defined tasks to address the issues, and influenced their market by improving means, methods and owner perception of their services. These forward thinking, proactive members created a mechanism for communication among all related parties that would advance the profession by improving safety, quality and value of pile driving construction.Micropile technology has evolved in the United States and around the world for the past four decades. The accumulated efforts of DFI and other, similar organizations such as The International Association of Foundation Drilling (ADSC) have contributed to this evolution. The advancement of the micropile industry – and consequently the micropile market – has been intimately tied to the execution of the mission of DFI."

Jan 1, 2017