Search Documents

By R. W. Smith, D. Clare

The removal of metals from an acid mine drainage (Leviathan Mine, Alpine County, California) water by precipitate flotation was investigated. The Leviathan waters vary from about pH 4.0 to pH <2.0and contain from about 2,000 to about 12,000 ppm SO42-.The main multivalent metals present in solution are Fe, Ca, Mg, Al and Mn. Both Cu and Co are present in small amounts. The pH was adjusted with lime. The collector used was either sodium oleate or tall oil. The sodium oleate was used as a function of pH to establish optimum flotation conditions and the tall oil was used only at the optimum pH. Dow Froth 250 was used as a frother. In some test additional Cu was added to the system. Excellent recovery of Fe and Cu were achieved at optimum pH. The process achieves results comparable to precipitation and filtration without as much problems with screens blinding because of less material to filter.

Jan 1, 2004

By P. Muduli, Y. Xi, T. M. Yegulalp, A. J. Arias

A short review of current practices and recent developments is followed by a description of a newly developed approach for solution of the optimum, ultimate pit limit problem. The new approach utilizes network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson (1956). Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method automatically includes several optimal solutions based on a predetermined number of benches to be included in the analysis.

Jan 1, 1994

By David C. Slack

In recent years public concern over the environment has grown enormously. A very aware populace has exerted pressure on its legislators to enact enforcement laws dealing with pollution. Among the different types of pollution, sulfur dioxide in the air is a large and readily identifiable constituent. Air pollution, according to the EPA, costs the U, S. billions annually with SO2 a major portion of this cost. Fossil fuel and oil fired power plants release better than 50% of the SO2 in the country. Thus great attention is being focused on the methods power plants are utilizing to control emissions. With a time schedule of compliance by early 1975, decisions are being made and systems chosen that will have to perform - and perform - and perform. Therefore, a large majority of the power plants are presently considering lime in the planning and operational phases of their stack gas desulfurization programs. The reasons for this are: Lime scrubbing has more development and pilot work completed than most other methods; the removal potentials are relatively high; the stoichiometric ratios are not excessive and, the process has relatively low capital and operating costs. Many pilot plant studies have been completed recently using lime and the first operational full scale lime scrubbing unit is now in the start-up phase at this time at Duquesne Light Company&apos;s Phillips Station here in Pittsburgh. Also, because of completed development work, the problem of solid waste disposal will also be tackled at this power station at the same time. There are various methods for the use of lime in scrubbing for S02, but for our purposes I would like to describe the cyclic wet lime process. This method called "Scrubber Addition of Lime" involves contacting the flue gas with a slurry of milk of lime.

Jan 1, 1973

By Jess W. Smith

The carbonaceous Monkemeyer sandstone member of the Creede Formation on Bachelor Mountain hosts alteration and mineralization which contrasts with other silver deposits of the Amethyst system. More than 20 million ounces of silver are contained in disseminated mineralization in the volcaniclastic conglomerates and sandstones. Hydrothermal fluids entered the Creede Formation directly from the Amethyst fault system and mixed with flowing meteoric ground waters trapped beneath the Monkemeyer sandstone. Portions of the basal rocks of the Creede Formation were argillically altered by more dense acidic fluids generated by boiling. The carbonaceous base of the Monkemeyer and much of the conglomerates below were mineralized and well silicified. Deposition of the mineralization resulted from two processes: (1) reduction by carbon in the Monkemeyer, and (2) fluid mixing in the conglomerates. Monkemeyer mineralization is confined to the carbonaceous basal material and silver content is relatively consistent. Silver is contained in acanthite which is commonly associated with traces of galena, chalcocite, covellite and sphalerite. Fluid mixing and mineral deposition in the poorly sorted conglomerates was controlled by the highly variable porosity and permeability. Anomalous silver contents are dispersed throughout a large volume of conglomerates but zones of higher silver content reflect the crude layering of the conglomerates. Acanthite is finely disseminated in pore spaces and partly replaces some detrital magnetite. other metallic minerals are rare in the main zone of mineralization.

Jan 1, 2013

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By Kendrick C. Hardcastle

Although the basic techniques employed in hydraulic pumping in open pit mining have been practiced throughout the better part of this century, only relatively recently have studies of&apos; sufficient depth and scope been conducted to improve these techniques. This paper will point out the basic techniques involved and some of the more recently discovered data concerning hydraulic pumping, Inherent in all hydraulic transportation systems apart from the consideration of transportation cast, is the outstanding advantage of slurrying the matrix at the mining pit so as to provide a lengthy and thorough soaking and washing of the material while in the pipe line and thereby reduce the necessity for washing, scrubbing and other treatment in the beneficiation plant. This is quite important in view of the constant increase in demand for a cleaner product.

Jan 1, 1964

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By Peter J. Tarkoy

The art of predicting rock excavating machine performance has become increasingly detailed and refined. Researchers using laboratory experiments and machine manufacturers using field observations have identified and defined mechanisms of failure, rock and tool interaction, and relevant design principles affecting them. Concurrently, practitioners have developed index tests which reflect rock properties relevant to machine performance. Empirical relationships between index properties and machine performance (penetration rate, cutter consumption, and machine utilization) have been established from past experience and are currently used throughout the industry. Contractors have used such relationships for estimating throughout the world. The detail in which geological, geotechnical, test, and project data, empirical relationships, and construction experience are utilized, is limited by time constraints imposed by the bidding period. To fully utilize all available data, methods of analysis, and construction experience, a simple computer program was developed for a microcomputer costing less than $7500. As a result, 1. machine performance predictions are detailed & reliable, 2. construction alternatives may be examined, 3. anticipated conditions & performance are graphically, documented & easily comparable to those encountered, and 4. results include a listing of assumptions & results of performance analyses & a graphic performance summary.

Jan 1, 1979

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By P. M. Lin

The problem of surface subsidence over abandoned mine lands is becoming more common due to the development of housing in suburban areas of abandoned mined lands. Subsidence can induce damage to estate properties, engineering structures and the environment. Houses, buildings, roads and utility pipelines may be fractured or broken or may collapse due to subsidence. The ground surface may be depressed and sink gradually or suddenly. The surface and subsurface water flow may be disrupted causing a change in flow pattern or depression of the water table. However, techniques for predicting abandoned mine subsidence are not yet well developed. Presently, one cannot predict when and where mine subsidence will occur. People have to wait until it occurs and then apply a suitable measure to remedy the damages.

Jan 1, 1990

This paper describes the characteristics of blasting which set it apart from other methods of breaking rock. The mechanism of rock breakage and the influence of rock proper- ties are then discussed. The strain and fragmentation produced by a cylindrical charge does not change once the charge is longer than 16 blasthole diameters. The influence of bench geometry, charge length and drill diameter are then examined. It is shown that spherical charges have advantages over long slender cylindrical charges. By selection of the appropriate drill diameter, explosive and charge configuration the optimum blasting practice for a given rock to give suitable fragmentation and muckpile profile for sub- sequent handling can be found. The fragmentat- ion depends not only on rock and explosive properties but also on the pattern which dictates how effectively the cracking is utilised. The size distribution of the fragments is given by the Rosin - Rammler equation. Undesirable cracking of the rock in the final wall can be controlled by the careful design of blasts as they approach the final wall. Finally, it is concluded that because of the distance to which blasting can fracture and then displace rock it is suited for the breakage of large volumes of rock.

Jan 1, 1978

By S. Kelebek, A. Khan, J. Caceres, Beckett. D.

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance. The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents."

Jan 1, 2003

By William S. Roberts

The Bureau of Mines has initiated a program to determine the availability of land for mineral exploration and development in Alaska. Researchers involved in this pro-gram are comparing land availability, based on ownership and government policies and regulations, to the distribution of known mineral deposits and terranes. This report on southeastern Alaska presents the findings of the first of six regional studies that will cover the State. The study consisted largely of data compilation and analysis using various mapping techniques. Summary land availability data are presented on copies of U.S. Geological Survey (USGS) quadrangles at a scale of 1:500,000. Five categories of land availability were identified: open to mineral exploration and development (approximately 9.4 million acres, or 38% of the 24.8-million-acre study area), open but with possible use restrictions (4.2 million acres, or 17%), selected (0.5 million acres, or 2%), patented (0.74 million acres, or 3%), and formally closed to mineral exploration and development (10 million acres, or 40%). Of the 1,187 known mineral deposits in the study area, approximately 38% are on land in the open category. Mineral terranes comprise approximately 6.7 million acres, or 27% of southeastern Alaska. Approximately 34% of these terranes are on open land.

Jan 1, 1985

From the mid-1970s ZC Mines at Broken Hill had a policy to increase ore production rates at progressively lower head grades. In the mid-1980s the mine suffered crippling losses at a time of low metal prices. An important contributory factor was the inherent geological distribution of metal grades in the seven defined ore lenses. Grades are bimodal, and perhaps, trimodal, in each ore lens. There is a tonnage deficiency in the critical cut-off grade zone of 7-10% Pb+Zn. Lowering the cut-off grade introduced siliceous and pyrrhotitic material which resulted in significantly poorer metallurgical performance. This example shows that the mine geologist needs to know the grade distribution of the orebody and to convey clearly the downstream implications of changes in the head grade.

Jan 1, 1990

The Kunwarara magnesite deposit is the largest known magnesite (MgCO3) deposit in Australia. It is located under black soil plains to the north of Rockhampton in Queensland. The deposit consists of magnesite nodules set in a fine-grained sandstone, siltstone and mudstone matrix. The magnesite is derived from weathering of serpentinite in adjacent hills and transport of magnesium in solution to a Tertiary/Quaternary river system. The magnesium has come out of solution in the active river system, and combined with atmospheric and biogenic CO2 to form magnesite nodules. The magnesite can be very pure with certain varieties up to 98 per cent MgO (LOI free). The deposit has been mined since 1991 and processed into magnesia (MgO) which is sold into refractory, agricultural and other markets. The geologist is an integral part of the small mine technical team. The role of the geologist includes characterisation of the ore through drilling and bulk sampling, supervision of geological aspects of mining and assistance in the optimisation of ore processing.

Jan 1, 2000

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987