Search Documents

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By R. W. Barbaro, R. V. Ramani, K. V. K. Prasad, P. T. Luckie

Discussion by A. Unal Barbaro et al. (1990) implemented a tedious study aimed at delineating the short-scale spatial variability of sulfur in a coal seam. It is not possible, however, to extend their conclusions to any other coal seam or use their in any other fashion, because the background geology was not presented. Nor were the conclusions accompanied by geological interpretations in the paper. In addition, an unfortunate printing error occurred where the total sulfur (determined by High Temperature Combustion) variogram in Fig.3 was duplicated in Fig. 2 instead of the seam height variogram. A more serious error, however, has been committed in the definition of the variable, seam height. What is defined as seam height by Barbaro et al. (1990) is, in essence, mining height, and is not a regionalized variable that should be studied by geostatistical methods directly. Despite the fact that the variable, seam height, is not defined in the paper explicitly, the following quotation discloses the fallacy: "All roof rock that exceeded 1.8 m (6 ft) from the floor was not taken because the longwall was operated to not mine more than 1.8 in (6 ft) unless the coal seam height exceeded 1.8 m (6 ft)." From this definition, the seam height, and therefore the sampling height, is equal to the actual coal thickness, if the coal thickness is greater than 1.8 m (6 ft). Otherwise, it is equal to the sum of the coal thickness plus the thickness of the roof rock that complements the thickness to 1.8 m (6 ft). In the latter case, the seam height is constant and equal to 1.8 m (6 ft). It is possible to conduct a variogram study on a pool of samples that are realizations of two different variables. But the conclusions derived would not belong to any one of the two variables uniquely and, therefore, do not possess any significance. Geostatistical analysis is irrelevant for the sum of multiple regionalized variables formed by arbitrary selections. In a two-seam setting, for example, the mining height, as defined by the thickness of one seam at one location and the thickness of both seams at another location (due to quality and/or minimum thickness considerations perhaps), should not be used in the calculation of one common variogram. The two seams should be modeled separately. They can then be combined according to the specific purposes of the study. On the other hand, if a constant is added to a regionalized variable (to incorporate dilution perhaps), the variogram of the new variable will not change. Barbaro et al. (1990), surprisingly, does not give any geological interpretation of their results despite the fact that most of them can be explained by the origins of sulfur in a coal seam. The presentation of the results of a geostatistical study with no reference to the geology of the deposit is uninformative. It may also be misleading for the potential users of geostatistics, It is not unusual to find nuggets of pyrite in coal seams. In such cases, pyritic sulfur will probably display a spatial structure for only a very small distance that will appear in the experimental variogram as no spatial correlation. This very well known phenomenon is called the pure nugget effect in geostatistics (Journel and Huijbregts, 1978) and perhaps can explain the lack of correlation found for pyritic sulfur content. The lack of correlation found for the total sulfur content may also be explained in the same way because the total sulfur content is dominated by the pyritic sulfur content in this case study. One should notice, however, that the situation may completely be reversed after cleaning the coal. Not all of the inorganic sulfur should be expected to be in the form of pyrite nuggets in a coal seam. It may also be disseminated in the coal seam and it is expected that it follows a certain spatial structure. However, an existing spatial structure may be masked by including a part of the roof rock, rich in sulfides, into the seam thickness in an arbitrary fashion because areas having a sandstone roof sometimes are known to show a higher sulfur content due to the downward percolation of solutions rich in iron sulfides (Clark, 1979). Plants use sulfur in their growth processes. Much of this sulfur is bound organically during peat accumulation and coal formation (Cecil et al., 1978.) This suggests a spatial structure of some sort for the organic sulfur. However, it is not possible to test this hypothesis because the results obtained by the authors for the organic sulfur content are not given in this paper. For this reason, the conclusion that simple average of the nearby samples would provide the best unbiased estimates is questionable for organic sulfur and is not based on any substantial supporting evidence. It is suspected that no spatial structure was detected and this was due to high sampling and laboratory analysis errors. Before concluding that sulfur variability in the seam at the location of study was random, a more detailed study for the disseminated non-pyritic sulfur should have been conducted, not for the sake of scientific curiosity only, but also due to its utmost importance with regard to coal cleaning and emission control. Pyritic sulfur can be cleaned to a considerable extent, whereas organic sulfur can not, making the emission control strategies highly dependent on the spatial distribution of the organic sulfur (Knudsen, 1981). In the light of these facts, one wonders why Barbaro et al. (1990) did not present the results of their study for the sulfate and organic sulfur content. References Barbaro, R.W.. et al., 1990, "Short-Scale Spatial Variability of Sulfur in a Coal Seam,' Mining Engineering, Vol. 42, No. 11, pp. 1267-1269. Cecil, C.B., et al., 1978, "Geology of Ccontaminants in coal," report prepared for Environmental Protection Agency, North Carolina, 123 pp. Clark, W.J.. 1979, "An interfluve model of the upper Freeport coal Bed in part of western Pennsylvania," unpublished MS thesis, University of South Carolina, 57 pp. Journel, A.G., and [Huijbregls], Ch. J., 1978, Mining Geostatistics, Academic Press, London, 600 pp. Knudsen, H.P., 1981. "Development of a Conditional simulation model of a coal deposit," unpublished PhD dissertation, The University of Arizona, 109 pp.

Jan 1, 1992

By K. J. Reid

A historical background of the development of automated material balance packages is presented including a summary of currently available packages and a description of the present work at the Mineral Resources Research Center of the University of Minnesota. A brief mathematical statement of the problem is given and solution techniques discussed. The problems and difficulties normally associated with material balances, both hand calculated and computer calculated are described. Several aspects of the available material balance packages as related to the "user/computer" interface are evaluated in detail. Elements of the material balance packages that affect the solutions are examined and the relative performance of the main packages on specialized problems presented. Finally, areas associated with automated material balances that require further work before computer packages can be widely used in industry are outlined.

Jan 1, 1982

By R Bourcier, T Rafferty

Following an underground coal mine explosion, it is important that ventilation is quickly restored to ventilate the mine and affect a mine rescue. To achieve this, surface ventilation fans must be suitably protected from explosion damage, but still able to be quickly restored.A review of all Australian coal mine regulations was carried out, revealing that Australia has no prescriptive regulations that specify the design of explosion relief panels and the protection of ventilation fans in the event of an underground explosion.To better define the level of protection required, this paper reviews and extracts details from relevant major international regulations and standards on the subject.A suitable design methodology for the protection of ventilation fans is presented that could be applied in Australia, using a combination of explosion relief panels, appropriate isolation of the fan, and ventilation shaft/mine design.CITATION:Rafferty, T and Bourcier, R, 2013. The protection of surface ventilation fan installations from underground explosions, in Proceedings The Australian Mine Ventilation Conference , pp 169-173 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By H. A. Schwartz

FROM time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion1 of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composition: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213° to 1132° C., the latter figure agreeing with Gontermann's data .2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the metastable diagram, from a temperature somewhat below the eutectic freezing point to a temperature below Ar1 and for a graphitic-carbon content from practically nothing to the original total carbon of the specimen (see Fig. 6). More especially we desired to locate the line in the stable diagram corresponding to the Acm line of the metastable system, which is designated by analogy, the Atm line (tm from temper carbon) ; also to determine the location of Aim with respect to Acm toward their lower extremities at Ar1 in order to determine whether or not graphitization is completed by the separation of an iron-carbon eutectoid analagous to pearlite in the iron-cementite system. This would involve further a comparison of the locations of the stable and metastable A1 points.

Jan 8, 1922

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

By R. R. Mankowski, F. J. Cox

Experimental results are presented on the longitudinal atenuation of a kinetic shock wave traveling along a typical mine hoisting cable. Mathematical curve-fiting of the results established these losses to be exponential and tension-dependent. The reflection and power-transmission coeficients of a typical winding drum were also investigated. The degree of penetration of an incident stress wave onto the coil of cable wrapped round the drum is shown to be governed by a second-degree relationship, and is solely dependent on the acceleration of the cable at the cable-drum interface. Although the investigation is limited to the testing of a single hoisting cable, certain qualitative trends that were identified can be generalized and applied to other types of hoisting cable with diferent geometries, elastic properties, and instalations.

Jan 1, 1986

By S. R. Zimmerley

[In the course of a flotation investi£ation, a siliceous gold ore was ground in a'ball mill to ':1inns 300-meeh. It wa. found that the small amotIDt of _Ius 300-mesh material had a gole.. assay approximately twice that of the oriGinal ore, &~d that this overs.ize nroduct also contained much abrac..ed iron. .,Joreove I the gold assay of the abraded iron t which was !1epnrated ma§metically', ~iVFl.£ eight ti;nes that of the are. These facts suggested that some r31aticnship ex?...,ted between the abnorma11y high gold content an the prese:1ce of brA-cit)" iron. It was decided, therefore, to investigate furt~er th~ Fl.Gsociation of the bold ~ith the iron abraded from the balls during sri~Qing ]

Jan 1, 1937

By Thomas R. Larson

"Many concentrators use re-circulating “plant” water for dilution in their flotation circuits. However, if crusher dust suppressants, ball mill grinding aids, or even agitator bearing grease are introduced into this water, and the water itself is not subject to cleaning steps, then sufficient quantities of these chemicals may appear in the flotation cells and begin to impact the flotation separation. A bench flotation procedure has been coupled with statistical analysis in order to estimate the impact of small quantities of non-flotation chemicals on flotation performance.INTRODUCTIONCleveland Cliffs produces iron oxide pellets for blast furnace feed, and is developing the capability to produce ferrous metallic products to supply a wider customer base. Cliffs manages five North American iron mines, including the Wabush mine sites in Labrador and Quebec. Based on various characteristics of the ore bodies, the flow sheets of the five mines are diverse. For example, Hibbing Taconite uses magnetic separation alone as their primary upgrading method, but Northshore and Empire use magnetic separation followed by flotation, and Tilden uses flotation alone. Last but not least, the Wabush concentrator upgrades primarily with gravity and electrostatic separation techniques.At Northshore, concentrate from the magnetic separator circuit is fed to a reverse flotation circuit. By design, the magnetic separators operate at the highest possible recovery of magnetite, as the separator tails are discarded, and relatively high silica content was acceptable to Northshore’s customers. As the steel-making industry moved toward lower and lower slag volumes, the silica content in the magnetic separator concentrate became a problem. The flotation step was added in the late 1980s in order to decrease the silica assay of the magnetic separator concentrate to meet the current customer requirements. In this setting, the flotation feed stream contains very little silica that occurs as liberated quartz particles. As the degree of liberation of the flotation feed stream is then a limiting factor for silica removal, the online grind control then was linked to flotation in the overall plant control system so that grind can be adjusted to achieve improved liberation if necessary for the flotation process."

Jan 1, 2002

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957

By William Gleason

"Ed Rapp is among those who believe in the saying that necessity is the mother of all invention. Rapp is the president of Caterpillar’s mining group. As such, he is tasked with leading the world’s largest mining equipment maker, and its customers, through this time of lower commodity prices, while also positioning his company to be prepared for better days that lie ahead.The decade-long mining boom fueled by growth in emerging markets and demand for commodities that led to record prices for some metals paused in 2008 with the global financial crisis. However, according to Rapp, thanks to stimulus packages around the world, and in particular the stimulus from China that was focused on infrastructure, the mining sector recovered fairly quickly, and from 2010 to 2012, mining was strong.And then the stimulus stopped. Credit dried up and global growth began to slow down and, in the three years since, commodity prices have declined by an average of 60 percent. Caterpillar expanded during the boom, acquiring Bucyrus, and investing billions into the mining sector. It has felt the pinch of the slowdown as much as any mining company in the world. These pages, and those of other mining publications as well as mainstream media, have been filled with stories of doom and gloom about the industry. But Rapp, while acknowledging that the difficult times have been painful, also said Caterpillar sees opportunity in the slow down and reaffirmed his company’s commitment to the mining industry as absolute."

Jan 1, 2014

By R. T. Webber, R. B. Owen

The vapor phase deposition of molybdenum and tungsten from the hexacar-bonyls has been thoroughly investigated by Lander and Germerl, and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2'3 could be similarly deposited, but did not investigate this metal extensively. Recently, conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. Apparatus and Technique The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T² and T3 containing crystals of the carbonyl. T² is kept in a constant temperature bath (not shown), while T³ is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Se, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by Sb is used to determine the volume included by S4, S6, SB, Slot the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: (I) the specimen temperature, from room temperature to about 1000°C, (2) the carbonyl vapor pressure, from 40 to 220 microns, and (3) the hydrogen flow. In several runs, 0.8 to 1.8 PCt of hydrogen sulfide was introuced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1949

By A Bax, G Wardell-Johnson, A Giblett, W Staunton

This paper presents a number of key considerations for process development testwork as a reliable basis for the inclusion of gravity separation in gold recovery flowsheets. Operating data, experiences and numerous case studies are also discussed in support of identifying best practice principles for gravity circuit design.CITATION:Giblett, A, Bax, A, Wardell-Johnson, G and Staunton, W, 2013. A review of best practice in gravity circuit design and operation, in Proceedings MetPlant 2013 , pp 272-284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Douglas Rudenko

When blasting complaints come, as an industry we often immediately look to the ground vibration as the source of the trouble. Often times we overlook or place less emphasis on the collected air overpressure data. Air blast like ground vibration is an undesirable side effect of blasting and can produce considerable structural response.

Jan 1, 2002

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

Provide a means to (1) rapidly disconnect a multifunctioning signal channel from a multichannel data collection system, (2) protect electronic devices from damage while causing the minimum amount of data collection disruption, and (3) operate electronic devices under gassy mine conditions. Background Data collection system instrumentation and cables are often located in hazardous areas of underground coal mines. As a result, frequent damage to the instrumentation cables occurs from roof falls, heavy equipment, and the relocation of air, water, and power lines. A similar problem exists in surface areas where cables and instrumentation can be damaged by animals and by vehicle traffic. Without a circuit-breaking feature, the damaged cables could cause instrumentation to be ruined, cause power supply failure, and otherwise disrupt data collection in some situations the lack of a circuit-breaking feature might cause an ignition in a methane atmosphere.

Jan 1, 1990

By K. P. Wang

SIGNIFICANT general developments took place in the Far East during 1964, with far-reaching repercussions on the mineral and industrial economies of individual countries and the region as a whole. Japan, during this, "the Year of the Open Door," ushered in the era of industrial maturity, greater independence in economic policy, and expanded technical assistance to less developed countries. Symbolic of its dynamic economic growth is the fact that Japan out-produced the Federal Republic of Germany in steel during 1964 to take over a third-ranking world position. Mainland China, recovering from the "Leap Forward" debacle, made significant gains in industrial output. Mainland Chinese trade with Japan was on the upswing, and discussions were held between the Chinese and the Soviets for possibly resuming Soviet aid in industrial and mineral development. Meanwhile, United States aid to Taiwan was being phased out because of progress achieved. Rapprochement between South Korea and Japan was imminent late in 1964, a factor which may well affect South Korean mineral development. The Indonesian-Malaysian confrontation created economic difficulties in both countries. The war in Viet-Nam seriously disrupted industrial activities, particularly in the south.

Jan 1, 1966

By Raymond A. Binns

Exploration for undersea polymetallic sulfide mineral resources with high economic potential would be more effective given an ability to predict sites with particularly high gold contents (averaging say > 10 ppm Au). Herzig et al (1993) addressed this issue shortly after recognition that deposits in the back-arc Lau Basin (average 3.8 ppm Au) were enriched in gold relative to mid-ocean ridge sites (average 1.2 ppm Au). Small but significant numbers of hydrothermal sites with massive sulfide deposits averaging >10 ppm Au have since been discovered. The principal genetic factors underlying gold enrichment include depositional processes at and below the seabed, and the source of gold. It is timely to consider whether resolution of their relative importance can be translated into practical criteria for exploration strategies focused on especially gold-rich deposits. Comparing the ?grade? of seafloor deposits using analyses cited in research papers is fraught with difficulty, but there is no alternative at present to assuming that such averages provide an initial tenor guide. On this basis, four known polymetallic hydrothermal sites from convergent plate margins fit the exceptional-gold category with >10 ppm ?average? Au, while one from a divergent margin comes close: Sunrise (Myojin Knolls; 20 ppm ?average? Au) and Suiyo Seamount (28 ppm Au) in the Izu-Bonin Arc are frontal arc volcanoes dominated by rhyolite and dacite respectively, contrasting with more common mafic neighbor edifices (Iizasa et al., 1999). In both cases gold-rich massive sulfides occur in summit calderas with significant development of pumiceous volcaniclastic rocks, at depths around 1300 and 1370 m respectively. In the Eastern Manus Basin, PACMANUS (~1700 m; 14 ppm Au) and Suzette (~1550 m; 22 ppm Au) occur along the crests of volcanic ridges dominated by dacite/rhyodacite and andesite/mafic dacite respectively (Binns, 2004). Caldera structures are lacking. Although the Eastern Manus Basin is tectonically a rifted back-arc, its submarine volcanic edifices (picritic basalt to rhyodacite) have distinctly arc-style geochemical and isotopic affinities, differing from more typical back-arc basin basalts at the spreading axis further west (central Manus Basin). Probably as a consequence of transpression and a marked rupture in the New Britain subduction zone, submarine arc volcanism has here extended into the rifted back-arc region.

Jan 1, 2005

By G. Richards

The Trail smelter of Teck Metals Ltd. produces about 90,000 tonnes of lead per year through two stages of refining following KIVCETTM smelting. Bullion from the KIVCET furnace is first treated in a pyro-refining plant in preparation for Betts electrorefining which makes 99.99% pure lead. Pyro-refining consists of number of integrated unit operations to remove primarily copper, arsenic, antimony and tin. The operation of this plant to meet the specifications for electrorefining requires attention to bullion management and selective use of reagents. The processes used for pyro-refining are reviewed in terms of chemistry and control.