Search Documents

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

Within CRLÆs lifetime there have been a number of products that have proceeded through their life cycles. In each case market forces and technological advances have forced the cessation of the product. The company has then had to develop alternative outlets for its copper. Sometimes it has produced a similar product to fill the same market. In other cases the extra copper is sold as cathode. Today, CRL produces no semi-fabricated copper products and all cathode is sold. More recently, CRL has ventured into the sale of technology and manufacture of cathode motherplates. This area, whilst it is not what had been a traditional area of core business, has been found to be profitable.

Jan 1, 1998

By E. A. C. Chamberlain

New techniques for the continuous sampling and analysis of mine air are expected to replace traditional methods used for the early detection of spontaneous combustion. It has been established that the rate of evolution of carbon monoxide is the earliest indicator of incipient spontaneous combustion. Two methods of continuous monitoring of this gas are available and are now in use in the UK collieries. The first is the UNOR infra-red gas analyser, which is flameproof and may be used underground; the second is a system of tube bundles, which permits air to be drawn from any critical point in a colliery and analysed on the surface. Each system has its advantages and disadvantages but both provide the colliery manager with far more information on the condition of his pit than could previously be obtained by spot sampling and laboratory analysis. This paper describes the two systems presently in use and assesses likely future developments.

May 23, 1905

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By G. Olson, T. Mudder, T. Clark

An evaluation was made of an innovative chemical approach for controlling the biotic portion of sulfide oxidation of tailing and waste rock using thiocyanate. This lipophilic anion is selectively toxic toward acidophilic bacteria, including those that oxidize metal sulfides. Sulfidic materials from precious metal and base metal mining operations were treated with thiocyanate solutions and subjected to accelerated laboratory weathering at 1 to 50 kg scale in humidity cells, trays, and columns. Initial field trials were conducted at 13.6 t and 100 t scale. Thiocyanate at relatively low concentrations reduced ARD from 50% to over 99%, depending on the sample and specific ARD parameter measured. Test work also was done with phosphate as an agent to coat reactive sulfides, further reducing their oxidation by biological and chemical reactions. The combination of phosphate and thiocyanate treatment is the basis for a potentially comprehensive approach to ARD prevention and control. Additional research and pilot testing are underway.

Jan 1, 2004

By Petrus van Staden, Dragan Milanovic, Francisco Sánchez, Eero Kolehmainen, Carlos Frias

"Currently there is no economical and viable process for on-site metal extraction from Low Grade, Complex or Poly-metallic deposits, and even more, there is not any industrial process or technology able to deal with polymetallic or bulk concentrates containing Cu+Zn+Pb base metals and also precious metals. Traditionally, metals recovery from polymetallic sulfide deposits is performed by mining, selective flotation to separate Cu, Pb and Zn concentrates, and finally, smelting/refining of those concentrates to obtain the refined metals. In many cases, selective flotation of that kind of complex ores produces low metals recovery and low concentrate quality containing impurities such as Hg, As, Bi, etc., which results in high penalties in treatment and refining charges, and consequently, worsening the economy of the mining business. Recovery of the valuable metals from Polymetallic, Complex or Low Grade ores could then be maximised by producing bulk concentrates or middling flotation products to feed novel hydrometallurgical processes, like the integral metallurgical system that is currently under development within the INTMET project. For example, producing bulk concentrates would increase more than 100% Cu+ Zn+Pb cumulative recovery versus conventional selective flotation. Founded by the Horizon-2020 EU Programme, the INTMET Project was started in February 2016 and will be running over three years. The INTMET consortium is led by Cobre Las Cruces (Spain) and integrates twelve partners from seven EU countries, and including Serbia and South Africa as well. The INTMET project represents a challenging opportunity to develop suitable technological solutions to deal efficiently with difficult, polymetallic and complex sulphide ores that are abundant in Europe and worldwide. Main activities carried out during the first 18 months of the INTMET project development includes: (i) An atmospheric leaching pilot plant having a capacity of 300 kg/h bulk concentrate which has been installed and operated continuously for nine months at the Las Cruces mine; (ii) Pressure leaching test work developed by Outotec; (iii) Bioleaching test work performed by Mintek in collaboration with MMI Bor. Prior test work was applied on bulk concentrate samples supplied from Spain, Portugal and Serbia. Some of the results of these technological developments have been very positive and are presented in this paper."

Jan 1, 2018

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

By M. L. Sorokin

The thermodynamic of nickel production from laterite ore and from sulfide concentrate can be analyzed using PO2 - PS2 diagram of the Ni-Fe-S-0-SiO2 system. The procedure of the diagram computation is suggested and the diagrams for various temperature and Fe/Ni ratio are calculated. Three-suffix Margules equations are used for the calculation of the thermodynamic properties of three solutions: liquid matte, liquid slag and solid Fe-Ni alloy. The diagrams are used for the considerations about direct one-stage metallic nickel production.

Jan 1, 1994

By James H. Allen

The development of large diameter rotary drilling techniques and equipment in the last nine years has been the main factor for the rapid advancement made by this method of shaft construction. In 1959, less than 5000 ft of large diameter hole was drilled in the United States for the mining and construction industries. By 1967, large diameter hole footage had increased to 117,000 ft. Part of the increase in footage for holes drilled represents AEC requirements due to the discontinuance of atmospheric testing of nuclear devices. The increase in footage for holes drilled for the mining industry can be attributed to cost savings of shaft construction by rotary methods as compared to conventional blasting methods. Until the late 1950&apos;s most large diameter holes were drilled with positive displacement rig pumps or air compressors, direct mud or air circulation, conventional sized oil well drilling strings, and multipass reaming techniques. In some very soft formations it was possible to run a pilot bit with one or more hole openers in tandem to drill the hole in a single pass. The main problem with single pass drilling using tandem hole openers was in providing sufficient circulation fluid for proper hole cleaning through conventional sized drill pipe.

Jan 11, 1968

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By J. Seo

We propose a dynamic biomechanical simulation method that uses motion capture to evaluate the risk of Work-related Musculoskeletal Disorders (WMSDs). Statistics show that WMSDs accounted for 33% of all non-fatal occupational injuries and illness in construction in 2009, and were a leading cause of temporary and permanent disability. Present methods rely largely on self-reports from workers, observational techniques, and direct measurements of motion and muscle activity to assess awkward postures, physical loads, repetitiveness, and the duration of exposure. While these methods have helped to prevent WMSDs in construction work, they may not be suitable for estimating the internal tissue loads associated with WMSDs. We propose a dynamic biomechanical simulation method to estimate internal forces and moments at each body joint of construction workers with motion capture data. Particularly, we explore the biomechanical loads by simulating active 3D musculoskeletal models based on measured postures and movements. To demonstrate the feasibility of this approach, we studied a ladder climbing task using a portable ladder under controlled laboratory conditions. Postures and motions were determined with a commercial motion capture system (e.g., VICON). The results were analyzed to investigate the feasibility of identifying risk factors based on biomechanical simulation. The results show that the proposed approach allows us to determine the biomechanical basis for WMSDs, and to identify postures and movements associated with excessive physical demands on each body joint. When combined with marker-less motion capture which is our ongoing work, the proposed approach has the potential to assess an individual?s motions and to provide personalized feedback for the purpose of reducing biomechanical loads and WMSD risk in real workplaces.

Aug 1, 2013

By V. T. McLemore

The Wind Mountain (WM) nepheline syenite deposit is part of the alkalic complex in the Cornudas Mountains, which ranges in age from 34.6 ± 1.5 Ma to 36.8 ± 0.6 Ma. The WM deposit consists of a complex, zoned pluton that ranges from syenite porphyry to nepheline syenite porphyry. The WM deposit has potential use for ceramics and dark-colored beverage containers and consists of nepheline, k-feldspar, albite, and varying amounts of other minerals. Analcime also is present locally but must be avoided because it is unsuitable for ceramic and glass. Chemically the deposit consists of 56-63 % SiO2 17-21 % Al2O3 and 4.0-5 % Fe2O3. Although initially iron is high, when the crushed rock is passed through a specialized magnetic separator, the iron content drops to below commercial maximum standards of less than 0.5% Fe2O3. The WM deposit is currently under exploration and testing to determine marketability.

Jan 1, 1994

&apos;Industrial Minerals - their mining and use in New Zealand&apos; is the theme of the 1978 Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy. This paper describes the use of phosphate rock, sulphur and potassium chloride (potash) - three industrial minerals which have enabled the farmers of New Zealand to increase production to current levels. The growth of imports of these raw materials for the New Zealand fertiliser industry is well documented in NZ Fertiliser Statistics 1977. This is the most recent of the Ministry of Agriculture and Fisheries annual publications on this Subject prepared from the detailed returns of fertiliser manufacture and sales from each fertiliser works. There are now 12 of these works in New Zealand one of the most recently established being in Whangarie where this conference is being held. Its capacity to manufacture superphosphate will shortly be 300&nbsp;000 tonnes twice that when it opened late in 1964. New grinding and manufacturing equipment comes on stream early in 1979. This paper illustrates the interdependence of two primary industries, agriculture and mining. New Zealand&apos;s economy in the foreseeable future will be based on agriculture so that our standard of living is dependent on the overseas prices and freight costs of the bulk raw materials from which our fertilisers are made. For the year ended 31 March 1978 New Zealand&apos;s total exports were $3395 million, of this total $2413 million (71%) came from the products of pastoral agriculture (wheat, wool, dairy and other animal products), $291 million from forest products and $501 (15%) from manufactured exports. Approximately half of the pastoral receipts can be attributed to the fertilisers applied at a total cost of about $200 million including subsidy.

Jan 1, 1978

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By Maust. E. J., W. R. Crane

"IntroductionIn the study of mine drainage in the red iron ore mines of the Birmingham district of Alabama, an extensive series of measurements were made in order to determine the drainage from the area overlying and adjacent to the mines. Gaging rods were generally used in measuring streams, and weirs in ditches and sometimes as a check on rod work. These tests in turn were checked by current meter tests. In all, 725 separate stream gagings and 97 weir measurements were made. Certain relationships were worked out, particularly between rod and weir tests, which permitted obtaining results that are much more accurate 'under the existing conditions, than any available formula would give. The large number of weir measurements and the period covered by the tests made it impracticable to construct a weir for each observation so portable, adjustable weirs were built. The methods used are described here for the benefit of those interested in measurement of streams in connection with a study of mine drainage or otherwise. The Drainage AreaThe area draining the mining district lies between the crest of Red Mountain and Little Shades Creek, and for convenience was divided into sub-districts adjacent to certain groups of mines. Gaging stations were established on Little Shades Creek at the upper and lower boundaries of each sub-district, also at points on the tributaries near their junction with the creek. The difference between the volumes of water flowing in Little Shades Creek as it entered and left the sub-districts represents the flow from the tributaries on both sides of the creek. Since the flow coming from the sub-districts was measured direct, the inflow from the tributaries on the opposite side of the creek can be computed from the three volumes determined."

Oct 1, 1926

The mineralogy of nickel slags from the flash smelter of Western Mining Corporation Ltd. at Kalgoorlie was studied. Residual magnesium silicates in the sulphide concentrates raise the melting point of the slag and result in the formation of magnesium-rich olivines. Addition of lime lowered the melting point, and, in slowly cooled slags, resulted in the formation of a pyroxene.Magnetite and sulphides were also present in all slags.The converter slags contained an olivine near fayalite in composition, together with wiistite, magnetite, and a little sulphide.Accretions from the hearth of the flash furnace were largely composed of magnetite with subsidiary olivine similar in composition to those of the flash furnace slags.Wall deposits, however, were largely composed of nickel ferrite and nickel-iron olivines.

Jan 1, 1976