Search Documents

By Roy Nilsen, Aravinda Perera

With the exponential growth of demand for minerals and need for diversification of supply channels, deep-sea mining is rapidly becoming inevitable. Productivity of underwater mining technology is salient to justify the deep-sea explorations. Methods for enhanced productivity of mobile mining equipment in a system level are investigated in this paper. Lessons learnt from the land-based mining has been the basis of this investigation. In general, mining productivity can be enhanced in two ways; firstly, by maximizing the amount of recovered material per unit time and secondly, by minimizing the cost of operation per unit material. Equipment that enable faster excavation, loading and transport in the seabed contributes significantly in increasing the amount of slurry per unit time. Improved mean time between failures (MTBF) of mining equipment will reduce the operational down time, thereby, contribute to maximize the amount of mined material per unit time. Several factors influence the operational cost minimization per ton of slurry. Higher efficient motor drive systems including the motor and PWM-fed inverter not only will save power but also will emit lesser heat thus the heat management can be less complex. This leads to more compact drive systems that allows higher power density, thus increased payload weight per empty vehicle weight. An energy storage method in the form of an utracapacitor in the electric drive system will also save the energy supply from the upstream.

Jan 1, 2018

By R. P. King

The central idea presented in this paper is straight forward. Some fairly obscure mathematical techniques are presented from the fields of integral geometry and stereology and these techniques are shown to provide workable quantitative relationships from which the liberation spectrum of an ore after comminution can be determined. The experimental data that is required can be obtained very accurately and conveniently by image analysis of polished sections of the original ore. This quantitative mineralogical analysis provides a bridge that can link the worlds of the mineralogist and the mineral process engineer. This paper has been written to introduce this quantitative approach to a wider audience in the hope that the approach will be used more widely and that the basic linear intercept analysis data will be measured for a wider range of mineralogical textures. This could lead to a more comprehensive characterization of typical mineral ores that will be of considerable use in practical mineral processing.

Jan 1, 1991

Organization Place Date 1918 American Society of Mechanical Engineers...:.. Worcester, Mass. June 4-7 American Institute of Chemical Engineers Berlin, N. H. June 19-22 American Concrete Institute Atlantic City, N. J. June 24-26 American Society for Testing Materials Atlantic City, N. J. June 25 28 American Institute of Electrical Engineers Atlantic City, N. J. June 26-28 New York Electrical Society, Annual Meeting... New York, N. Y. June American Institute of Mining Engineers Colorado Sept. 2-7 National Association of Stationary Engineers.... Cincinnati, 0. Sept. 9-13 British Iron and Steel Institute, Autumn Meeting London, Eng. Sept. 12-13 National Exposition of Chemical Industries New York, N. Y. Sept. 23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association.: Atlantic City, N. J. Sept.

Jan 6, 1918

By Terry G. A B

Before detailed design of Museum Station could commence, a number of factors had to be considered to determine its exact location within the city street pattern, the depth and the dimensions of the underground station. To arrive at a sound con- clusion regarding location, the relationship of the station to probable future city development had also to be considered.

Jan 1, 1981

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989

By Charles L. Kimbell

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not wholly devoted to mineral commodity transport, as seen in tables 16 through 22. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to non mineral goods, as well as carrying mixed mineral commodities and non mineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-off ships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Table 16 shows the distribution of the world's merchant fleet by vessel type in terms of the number of vessels, their gross tonnage, and their deadweight tonnage. The increase of nearly 1.5 % in the number of vessels between 1990 and 1991 compared with a 2.7% growth in gross tonnage and a nearly 2.3 % increase in deadweight tonnage points to an increase in the average size of vessels. Of the four categories of vessels reported, all showed increases in number and in deadweight tonnage between 1990 and 1991 except for "other," and on the gross tonnage basis, all groups registered increases. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1993

CLARENCE N. FENNER.-Mr. Gelstharp, chief chemist of the Pitts-burgh Plate Glass Co., has directed my attention to the fact that that company was using optical pyrometers obtained from the Leeds & Northrup Co. several months before the members of the Geophysical Laboratory arrived at Charleroi. I am glad to make this correction. The chief object of my paper was to emphasize the necessity of careful temperature control in the making of optical glass and to describe the kind of tests to which an optical pyrometer should be subjected at a glass plant in order to obtain information regarding the closeness with which its readings correspond with true temperatures under the condi-tions which prevail in each particular case.

Jan 12, 1919

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, )"Why automate?" Automation, automatic control devices and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with a minimum of instruments for the purpose of merely guiding the operators. Processes were manually controlled by the operator on the basis of simple temperature, pressure, flow and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction savings in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material through- put, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins or producing a new and saleable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure, and (2) units which both measure and control a process variable. In coal processing, the first class of instruments, those which measure only, include analytical devices such as automatic ash, moisture and sulfur measuring units and the simple pressure, temperature, flow and level indicating devices mentioned previously. The second group of instruments, those which both measure and control, include a wide variety of units such as continuous weighing devices on conveyor belts and photoelectric cells which gauge the position of railroad cars on the track and insure that the cars are in the proper location for loading (see Chapter 15). The latter types of units as used in the coal industry differ from those used in other industries in one significant point. In coal processing these instruments need not be as highly sophisticated and accurate as in other industries; hence their cost is proportionately lower than in other industries. Because of the economic fact that coal sells for only a fraction of a cent per pound compared to dollars per pound for many chemical products, and

Jan 1, 1968

Escondida is a state-of-the-art copper mining operation. It is the major copper project of the 1990s and is the largest new investment in the industry - a US$823 million project. It accounts for about six per cent of Chile's total exports, making Escondida the largest private exporting company in Chile.

Jan 1, 1992

By A Weeks, W J. Shaw, A Kuk

Grade control is a process that requires the interaction between many components of the mining operation and successful grade control is only realised through good data, robust systems, and a well-trained, motivated and disciplined workforce.The Mt Magnet Gold Project Pty Ltd (MMGP), a wholly owned subsidiary of Ramelius Resources Limited, started mining at Mt Magnet in February 2012 with high expectations for success. Positive cash flow would fund an aggressive exploration and mine development program in the area to increase mine life. Disappointment followed when after start-up the operation had issues achieving budget grade and realising the predicted grade of the mined ore. In January 2013, things started to improve. During the next six months, gold production steadily increased with successive months achieving record production. What had changed?Improvements started following the realisation that controlling grade was not the sole responsibility of the mining geologist and that everyone on-site has a role to play. This paper examines the factors that delivered success for MMGP.CITATION:Weeks, A, Shaw, W J and Kuk, A, 2014. Who is responsible for grade? – an evaluation of the value chain at Mt Magnet Gold Project, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 477–482 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By S. Potgieter-Vermaak

The main mineral components of the so-called heavy sands (or black sand) are the titanium, zirconium and iron-bearing minerals, rutile, zircon and illmenite, accompanied by various minor and trace amounts of silicates or phosphates, often present together with the rare earth elements. The investigated samples originated from Richards Bay Minerals (RBM) in South Africa, which is jointly owned by BHP Billiton and Rio Tinto, the largest titanium slag producer in the world. The present study focused on the characteristics of samples originating from various points in the separation plant. The heavy-mineral fractions and concentrates of a representative suite of samples were investigated using various analytical techniques to establish the differences in morphological and elemental compositions at the different points in the plant. These techniques included: reflected light microscopy, micro-raman spectrometry (MRS), scanning electron microscopy coupled with energy dispersive X-ray analysis (SEM/EDX) and structural and chemical analyser (SCA). All samples comprised a heterogeneous population of zircon and rutile grains with diverse physico-chemical properties, expressed by large differences in colour and trace element chemistry of single grains. The elemental composition proved the presence of the rare earth elements that appeared to coexist with both Ti and Zr minerals. The percentage of grains hosting inclusions, such as anatase, monazite, quartz, spessartine, augite, epidote and actinolite, varied for each sample and could be uniquely characterized by Raman investigations. Keywords: heavy mineral sands, micro-ram an spectrometry, elemental analysis

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By David A. Larson

The future exploitation of crust deposits will require a dependable characterization system. The U.S. Department of the Interior, Bureau of Mines (Bureau) initiated research to develop a new sampling dredge by conducting a series of cutting and physical property tests on previously collected cobalt-rich manganese crust and substrate samples. Using the engineering parameters derived from these tests, a large, heavy dredge was designed and tested. This heavy dredge was capable of fragmenting and collecting in situ crust, but it created handling problems for the research vessel, thus an aggressive cutting, light-weight dredge was conceived and fabricated. The light-weight dredge is capable of fragmenting and collecting crust and some talus. This dredge can be used on flat or rough seabed terrains. It can be easily retrieved from hang ups and reset to sample again.

Jan 1, 1991

Iron formation-hosted iron ore deposits account for the majority of current world iron ore production and consist of three classes: unenriched primary iron formation with typically 25 to 45 wt per cent Fe; martite-goethite ore formed by supergene processes, with abundant hydrous iron oxides containing 60 to 63 wt per cent Fe; and high-grade hematite ores thought to be of hypogene or metamorphic origin overprinted by subsequent supergene enrichment with 60 to 68 wt per cent Fe.Individual iron ore deposits range from a few millions of tonnes to over two billion tonnes at >64 wt per cent Fe, although most are within the range of 200 to 500 Mt. In the Hamersley Province of Western Australia, martite-goethite ores are largely developed in the Marra Mamba Iron Formation, although high (>0.08 per cent P) phosphorous mineralisation is also well developed in the stratigraphically higher Brockman Iron Formation. Whilst the vast majority of high-grade microplaty hematite ore is best developed in the Brockman Iron Formation, this paper provides the first textural evidence of locally significant microplaty hematite mineralisation in the Nammuldi Member of the Marra Mamba Iron Formation, in the Chichester Ranges at the Christmas Creek, Cloud Break and Mount Nicholas prospects. Petrographic studies have identified a high-grade Fe texture composed of nanometre scale plates of hematite in mineralised sections of primary microplaty hematite deposits in the Pilbara and elsewhere, well below the normal depth of weathering or dehydration. The population of nanometre to micrometre scale hematite plates is interpreted to represent various stages of nucleation, crystallisation and progressive growth of hematite from the primary ore-forming fluid in areas that were once iron-rich carbonates or silicates in the BIF.

Jan 1, 2005

By N. W. Sager, H. W. Mossman

The arrangement and general dimensions of the reverberatory furnaces and waste-heat boilers for the Nos. 2 and 3 smelting units at the McGill plant of the Nevada Consolidated Copper Corporation are shown in Fig. 1. Each of the two reverberatory furnaces has its own set of waste-heat boilers, and before February, 1932, each furnace, when it was in operation, delivered waste-heat gases to its own boilers only. In January, 1933, the idea was suggested of using some of the waste-heat boilers as economizers to operate in conjunction with the waste-heat boilers that were generating steam. The execution of this idea gave rise to the gas-flow scheme depicted in Fig. 1, the advantages of which were obvious, particularly so in view of the fact that for some months prior to the adoption of this scheme the smelting had been confined to No. 2 furnace, with No. 3 furnace and its boilers idle. The waste-heat gases from No. 2 furnace pass through the boilers serving this furnace as steam-generating units, thence through the original exit duct to a point where a bulkhead diverts the gases in a reverse direction through two of the boilers of No. 3 furnace. After the gases have traversed these two boilers, another bulkhead placed in the duct between No. 3 furnace and its boilers causes them to traverse still one more boiler, from which the gas path leads to the stack. In this scheme the last three boilers traversed by the gases, i.e., the boilers behind No. 3 furnace, function as economizers and preheat the feed water for the two steam-generating units directly serving No. 2 furnace. This discussion will give consideration to the results obtained in waste-heat recovery by the scheme shown in Fig. 1, and, further, will compare these results with those obtained before the boilers of No. 3 furnace were set up to act as economizers, but before going into the detail of heat generation, distribution and recovery, will present some additional details of the equipment. All boilers in this waste-heat plant are of the Stirling type. The two behind No. 2 furnace, acting as steam-generating units, of class 13, are 40 tubes wide and rated at 1112 boiler hp., while the three boilers behind No. 3 furnace, acting as economizers, are also of class 13, but 28 tubes

Jan 1, 1934

Microstructural investigation has shown that grain splitting or deformation banding ( DB ) develops progressively with increasing strains during cold rolling. Of particular significance to simulating texture development in cold rolled BCC polycrystals is the operation of higher order slip systems other than 110 and, the occurrence of DB in the rolling plane since the latter allows a new relaxation of the shears. Deformation banding ( DB ) model includes grain subdivision in the rolling plane and applies the Relaxed Constraints ( RC ) mechanism for the other shears. An energy criterion for deciding whether deformation banding occurs or not has been postulated, referred to as Deformation Banding Criterion ( DBC ). This paper reports the results of the investigations into the effects of different slip systems, i.e., those based on 110, 112 and 123 slip planes and their combinations using RC, DB and DBC models, in developing simulated BCC rolling textures.

Jan 1, 1999