Search Documents

By Gary N. Greenfield

This morning, gentlemen, I should like to discuss resin anchors of a type introduced to North America approximately 2-1/2 years ago. We shall also briefly review the basics of mechanically anchored rockbolts so that a general comparison may be made. Previous efforts with synthetic resins were aimed at aiding a mechanical Or "point" anchor, obtain a better purchase in the rock mass. Resin cartridges of the type to be described in this paper are capable of achieving point anchorage or full encapsulation of mine roof or rockbolts. Of significance, therefore, is that unlike a mechanical bolt, placed and tensioned, celtite rockbolts may be fully grouted and tensioned or left untensioned in the installation sequence. Our principle effort has been to offer this system to mining and civil engineers who have encountered difficult rock conditions and wish to reinforce strata to achieve a greater degree of permanence and safety.

Jan 1, 1972

By S. J. Sindeband

Prior to discussing the metallurgy of sintered chromium borides, it is pertinent to outline some of the reasoning behind this investigation and the purposes underlying the work. This study was initiated as an aproach to the ubiquitous problem of a material for service at high temperatures under oxidizing atmospheres, and it was undertaken with a view to raising the 1500°F (816°C) ceiling to 2000°F (1093°C) or better. For the reason that no small, but rather a major, lifting of the high temperature working limit was being attempted, it was felt appropriate that a completely new approach be taken to this problem. A summary of the thinking behind this approach was published recently by Schwarzkopf.' In briefest terms, it was postulated that the following requirements could be set up for a material which would have high strength at high temperatures. 1. The individual crystals of the material must exhibit high strength interatomic bonds. This automatically leads to consideration of highly refractory materials, since their high energy requirements for melting are related to the strength of their atom-to-atom bonds. 2. On the polycrystalline basis, high boundary strength, superimposed on the above consideration, would also be a necessity. Since this implies control of boundary conditions, the powder metallurgy approach would hold considerable promise. Such materials actually had been fabricated for a number of years, and the cemented carbide is the best example of these. Here a highly refractory crystal was carefully bonded and resulted in a material of extremely high strength. That this strength was maintained at high temperature is exhibited by the ability of the cemented carbide tool to hold an edge for extended periods of heavy service. Nowick and Machlin2,3 have analytically approached the problem of creep and stress-rupture properties at high temperature and developed procedures whereby these properties can be approximately predicted from the room temperature physical constants of a material. The most important single constant in the provision of high temperature strength and creep resistance is shown to be the Modulus of Rigidity. On this basis, they proposed that a fertile field for investigation would be that of materials similar to cemented carbides, which have Moduli of Rigidity that are among the highest recorded. The cemented carbide, however, does not have good corrosion resistance in oxidizing atmospheres and without protection could not be used in gas turbines and similar pieces of equipment. It would be necessary then to attempt the fabrication of an allied material based upon a hard crystal which had good corrosion resistance as well. It was upon these premises that the subject study was undertaken and at an early stage it was sponsored by the U.S. Navy, Office of Naval Research. Since then, it has been carried on under contract with this agency. Chromium boride provided a logical starting point for such research, since it was relatively hard, exhibited good corrosion resistance, and, in addition, was commercially available, since it had found application in hard-surfacing alloys with iron and nickel. That chromium boride did not provide a material that met the ultimate aim of the study results from factors which are subsequently discussed. This, however, does not detract from the basis on which the study was conceived, nor from the value of reporting the results which follow. Chromium Boride While work on chromium boride proper dates back to Moissan,4 there has been a dearth of literature on borides since 1906. Subsequent to Moissan, principal investigators of chromium boride were Tucker and Moody,5 Wede-kind and Fetzer,6 du Jassoneix,7,8,9 and Andrieux." These investigators were generally limited to studies of methods of producing chromium boride and detennining its properties. Some study, however, was devoted to the chromium-boron system by du Jassoneix,7 who did this chemically and metal-lographically. This system is not amenable to normal methods of analysis by virtue of the refractory nature of the alloys involved, and the difficulties of measurement and control of temperature conditions in their range. Dilatometric apparatus is nonexistent for operation at these temperatures. Du Jassoneix made use of apparent chemical differences between two phases observed under the microscope and reported the existence of two definite compounds, namely: Cr3B2 and CrB. These two compounds, he reported, had quite similar chemical characteristics, but were sufficiently different to enable him to separate them. The easiest method for producing chromium boride is apparently the thermite process, first applied by Wede-

Jan 1, 1950

By Thomas Bannon

PROSPECTING for oil in Spain has been going on for many years but only in a very haphazard way and without adequate geological or technical advice. Shallow wells have been drilled in several provinces but, for the most part, they have been doomed to failure from the beginning because of unfavorable geological locations, inadequate drilling equipment inexperienced operators, or lack of sufficient capital. Geologists seem to agree that the most favorable chances for commercial fields are in the northern part of Spain where the petroliferous Triassic beds underlie Cretaceous and Tertiary sediments. The prov-vinces of Santander, Burgos, Alava, Vizcaya, Navarra, and Guipuzcoa seem to offer the most promising localities. Several shallow wells have been drilled near Villamartin about 60 Km. northeast of Cadiz. One of these wells produced a small quantity of light oil but was never operated. The Spanish Government has been drilling on a well in this district for some time, using the Russian free-fall drilling system. The present depth is about 3000 meters. Several years ago the Compania Petrolera Franco-Espanola drilled a well to a depth of about 700 meters near Elorrio, province of Vizcaya. A diamond-core drill was used. The well was located on vertical Cretaceous beds near an igneous dike. The same company, in March, 1923, made a new location about 500 meters away from the first well and the same distance from the dike, in beds dipping about 80°, and is now drilling its No. 2 well. The last depth reported was about 200 meters.

Jan 3, 1924

Established as a Society February 26, 1957 OFFICERS AND COMMITTEES Wayne E Glenn, President Earl M Kipp, President-elect John S Bell, Past President R A Morse, Vice-President W D Owsley, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 6300 North Central Expressway Dallas 6, Texas

Jan 1, 1960

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Frank Firmstone

The material described below was made at Furnace No. 2, Longdale, Va., Oct. 28, 1907, during a sudden derangement of working, in the course of which the furnace became entirely bridged over and for some time no solid material whatever descended into the hearth. This caused the hearth to become so completely emptied that, at the tuyere-level, a pricker put in at one tuyere could be seen by looking in at the opposite one. The tap-hole was opened and the iron got out with some difficulty. It ran sluggishly, throwing many sparks, but was not

Jan 1, 1909

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly. subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fumeless fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

By J. J. Krizek, A. H. Ditto

INTRODUCTION The Carr Fork property is situated in the Bingham Mining District located on the east slope of the Oquirrh Mountain range in Utah. The mine is adjacent to and lies west of Kennecott's Bingham Pit some 25 miles southwest of Salt Lake City. The Bingham Mining District contains one of the largest copper reserves on North America. Mineralization is associated with the Bingham stock which intruded through some 16,000 feet of sedimentary formations. Mineralization and a1teration zoning was developed radially from the Bingham stock with lower grade disseminated copper mineralization centrally located in the stock and adjoining quartzites. In addition, several garnetized limestone beds abutting the stock were also well mineralized. These skarns will be Carr Fork's initial mining target. Of the several limestone beds, only two, the Yampa and the Highland Boy have significant commercial interest at present. These beds which are 50 feet to 150 feet thick and are separated by 200 to 400 feet of quartzite were highly folded, thrusted and faulted, resulting in a dip variance from 20" to vertical. The predominant dip, however, is between 20" and 45" from horizontal. Quartzites surrounding the limestone beds were subjected to the same degree of tectonic activity with resultant intense fracturing and stress relief. The limestone beds which have a higher elastic modulus and which also experienced fracture healing during mineralization appear to have greater competency and strength than the quartzites. Four shafts nominally 3500 feet deep will provide access to the mine which will be a highly mechanized trackless operation, designed to produce 14,000 tons per hoisting day. First production is scheduled for the last quarter of 1979.

Jan 1, 1977

By Ji Wang

Reflective in-seam wave detection has the advantages of a far detection range and wide applicability. It has been successfully used in detection of many abnormal geological structures in work-faces, such as faults and collapse columns. However, a reflective in-seam wave is a dispersion wave. It has weak energy and is always covered by the direct in-seam wave. In the past, underground seismic explorations were not able to image the opposite roadway using reflective in-seam waves. To solve this problem, we propose a new method of reflective in-seam wave imaging based on adaptive dispersion filtering. This method processes the reflective in-seam wave using a filter with the parameter of transmission distance. The degree of similarity of the filtered and the explosion signal is used to estimate the transmission distance and image the reflective objects. We test and verify this method using real underground seismic data. This research is helpful for the detection of coal mine goafs and abandoned roadways in work-faces or in front of tunneling ends.

Aug 1, 2013

By S. A. Voltura

The Phelps Dodge Miami smelter has smelted copper concentrate using the ISASMELT technology since 1992. The design throughput rate was 591,000 tonnes/year and after a slow start-up, the production rate has exceeded the design after the seventh year of operation. In 2002, the smelter consumed 719,000 tonnes of copper concentrate and has the potential to hit the permitted rate of 772,000 tonnes/year. Improvements to the smelting vessel and the surrounding support processes have allowed for continuous improvement from start up until now. This presentation will outline the chronological events and the improvements completed to accomplish these improvements

Jan 1, 2004

By A. Berthet

In the past two decades, of the successive steps leading from iron ore to finished steel, the production of liquid steel and its preparation for the casting operation has probably undergone the most drastic evolution. The reason for this is the development of oxygen converters (top blown and later on bottom blown) and UHP arc furnaces which are replacing the conventional processes such as the open hearth and basic Bessemer processes. These new processes have been great advances, but it would certainly be quite hazardous to assert that the situation will remain the same for the coming decades. In fact, with the advent of continuous steelmaking a new generation of processes has now arrived. The research and development programme at IRSID on continuous an a steelmaking began ten years ago has progressed systematically in the following stages : First a comparison was made on a small pilot scale of various techniques : for example, refining in a runner by top or bottom blowing, pulverizing the metal stream by oxygen, using the mixing effect of a vortex, etc. but for various reasons these processes proved unsatisfactory and were abandoned in favour of a method using the so -called "emulsion refining".

Jan 1, 1972

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering program that culminated in this successful process. 1. Introduction The Pasminco US Inc. (PAS), Gordonsville Operation, has been producing zinc concentrate continuously since 1975. Within the zinc concentrate, several byproduct elements were found to be significantly concentrated including gallium and germanium. The gallium and germanium replace zinc and other metals within the crystal lattice structure of the zinc mineral (sphalerite) and are concentrated in the same manner as the zinc mineral. This concentrate is then sent to the Pasminco Clarksville Zinc Refinery for further processing. Within the hydrometallurgical zinc-processing plant at Clarksville, a residue is formed that contains a majority of the impurities that would otherwise contaminate or hinder the zinc process. Approximately 5,000 tons of residue is formed annually containing approximately 0.80% gallium and 0.60% germanium along with significant quantities of iron, zinc, silica, and lead. Pasminco currently sells this residue for the germanium value. Until recently, no revenue for the gallium was obtained from the sale of the residue.

Jan 1, 2008

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By J. C. Norman

Jan 1, 1985

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By Ivo Dreiseitl

Bottom sediment sampling by means of a box corer, as a direct method of deep seabed exploration for polymetallic nodules, is the most comprehensive way to obtain various types of geological information on points forming a network of stations. However, direct information is lacking from areas separating those stations and has to be approximated by interpolation or extrapolation, which leads to uncertainties. Sediment sampling with a gravity or piston corer can provide information on the superficial, up to 4 m thick, part of the sedimentary cover. As opposed to box coring, gravity or piston coring provides no information on nodule abundance. Information for unsampled areas can be gained by application of remote techniques of exploration. The techniques of choice in visualising nodule-rich fields, nodule-free areas, hard rock outcrops and other obstacles for seafloor mining involve using sonar and continuous deep sea (CDS) camera. Seafloor mapping can be rendered with two major sonar types: the side scan sonar used to obtain seafloor imagery and multibeam sonar for bathymetric data; the two types are usually combined and work with an intermediate frequency profiler. Photo-profiling by means of a deep sea towed camera provides a series of seafloor photographs, each supplemented with information on the area covered by each frame, including the nodule abundance. Remote techniques have been quite frequently applied by the Interoceanmetal Joint Organization (IOM) in nodule field exploration. Recently, geoacoustic techniques (side scan sonar + profiler) and CDS were applied for exploration of IOM?s first prime area H11 (5372 km2) on 6 transects. During the IOM-2009 cruise, a total of 295 km of geoacoustic transects and 344 km of photo-transects were surveyed. The data obtained were processed with the aid of earlier information produced by multibeam sonar surveys. The aim of this paper is to demonstrate the advantages of remote techniques, particularly with regard to application of the towfish device, for geological and geotechnical applications in exploration for polymetallic nodules.

Sep 14, 2011