Search Documents

By C. H. Bucknam

Metallurgical processing of gold ores in positive water balance environments has been facing decreasing discharge concentrations in permits and additional requirements to pass acute toxicity testing before discharges will be allowed to native fisheries. In response to the challenge to meet 0.005 mg/L free cyanide guidance for discharges to fresh water fisheries, the American Society of Testing and Materials (ASTM) International Cyanide Task Group has undertaken an interlaboratory study for the free cyanide method in the metallurgical processing cyanide detoxified reverse osmosis effluent to determine if the quantitation limit for the method could be lowered from the current 0.009 mg/L free cyanide (1) to less than the 0.005 mg/L guidance concentration. Results of the testing are presented below.

Jan 1, 2012

By E. W. Lindroos, Fred D. DeVaney, R. L. Bennett, R. W. Hernlund, W. R. van Slyke, W. F. McDermott, C. U. Keranen

INTRODUCTION Iron is the world's most widely used metal and constitutes about 5% of the earth's crust. Iron ores are found widely distributed throughout the world. Because of its wide occurrence and relatively low value, an iron ore to be merchantable must contain a relatively high percentage of the metal to be considered as a source of iron. Few ores containing less than 25% iron would be considered as ore unless they existed in large amounts and could be concentrated very cheaply. The grade of the ore, the ease of concentration, and the transportation cost to market are fundamental considerations deter- mining its worth. Iron never occurs as a natural metal except in meteorites. Most iron ores occur as oxides, and to a lesser degree as carbonates. A small amount is recovered as a byproduct from iron sulfides. Iron ore must be reduced (oxygen removed) to metal for use. Iron is marketed in many forms and combinations, such as pig iron and a great variety of steels. Iron is practically never pure as marketed but contains varying amounts of carbon, phosphorus, sulfur, and alloying elements such as nickel, chromium, etc., all of which affect the physical proper- ties of the end product. Please note that in this section all analyses ore on a dry basis and all tonnage figures are on a long-ton basis of 2,240 lb unless otherwise noted.

Jan 1, 1985

By M. C. Villeneuve, P. A. Siratovich

We present an integrated analysis of laboratory-based thermally induced fracturing and results of numerical models to give insight to the role of thermal shock fracture on geothermal reservoir rocks. Thermal stimulation is a reservoir permeability enhancement technique applied to commercial geothermal reservoir rocks to enhance fluid injection capabilities for spent power plant working fluids. The process is well known to enhance permeability but the thermodynamic and physical constraints of the process are less certain. In an attempt to constrain the interaction and the ideal conditions that lead to permeability enhancement, experimental procedures were carried out to mimic the conditions that a reservoir rock would experience during a thermal stimulation using temperature differentials ranging from 50-300°C. Samples underwent such thermal gradients under controlled laboratory conditions and were characterized for the changes to permeability, porosity, ultrasonic velocities, dynamic elastic moduli and petrological changes. The thermal stimulation was simulated in a FLAC2D thermal numerical model to investigate the nature of the thermally induced changes in the sample. The development of this model also allows us to investigate the relationship between geological characteristics and the ability to thermally stimulate any type of rock. The results indicate that numerical thermal shocking experiments are corroborated by laboratory-based results. The implication of this study is that the refined numerical models present an insight to the conditions and constraints under which thermal stimulation can prove to enhance permeability that could not be gained through purely laboratory-based studies.

Jan 1, 2015

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

One of the strategies introduced within Pasminco Mining to survive low commodity prices is to formally implement a `Quality Education System'. The net result has been a consistent approach to quality within and across mine sites. This `quality system' has been adopted in the technical computing environment and the immediate benefits have been: ò A clearer understanding of the systems, processes and relationships that involve technical computing. ò A re-focussing on customer (user) requirements. ò Inclusion of managers as customers with their own requirements of performance and quality, in addition to access to Executive Information. ò New ways to measure the `performance' of a technical computing environment which includes using maintenance costs. Observations are that there is an overlap between `traditional' information technology (IT) methodologies and quality systems being put in place in the broader workplace. This overlap is most apparent in the area of analysing customer requirements. In the IT environment customers are viewed as users, and their requirements determined by undertaking a requirements analysis. A data flow diagram traditionally used in the IT environment and not as a tool in quality systems, has been used in a novel manner to help identify the customers of the technical computing department. It has also been useful in illustrating the work processes and relationships between the entities in this diagram and in directing the future initiatives needed to fulfil the customers' changing requirements.

Jan 1, 1995

By D. J. Kemp

The 20th century saw changes in the mining and metallurgical industry not only technically but also in social and environmental expectations. As projects continue to become larger their visibility raises concerns among many groups. For mining companies, transparency, openness, and early engagement of all parties are fundamental to assure success. An equally important task is to anticipate the standards that will be required to meet society’s expectations in the 21st century.

Jan 1, 2005

By Robert R. Grinstead

Two new ion exchange resins have been developed, which selectively absorb copper and nickel in preference to ferric iron from dilute sulfuric acid solutions of pH 1-3. The first absorbs copper and not nickel and can be readily eluted with 1-2N sulfuric acid. This resin is well adapted to the processing of copper leach liquors, including relatively low grade liquors obtained from dump leaching. The second resin absorbs nickel as well as copper in the same pH region, but only the nickel is eluted with 1-2N sulfuric acid. Elution of the copper requires much stronger (ca. ION) acid, altho both species are readily eluted with dilute (ca. lN) ammonium hydroxide. This resin, which should be useful in processing of certain types of copper-bearing solutions, may also be suitable for treating acidic nickel leach solutions of laterites and other non-sulfide ores.

Jan 1, 1976

By F. Louis Grammer

The rapid advances on the mechanical side of blast-furnace practice have not always been accompanied by a proper appreciation of the metallurgical requirements. This is illustrated occasionally by the improper use of automatic barrow chargingdevices and bins (introduced at the expense of accuracy in weight), with ores of irregular composition or ores that have been poorly graded. The 100-ft. blast-furnace has not always been advantageous, and in many instances the increase in the number of tuyeres, from 8 or 12 to 20, has resulted in decreased output. The data pertaining to this division of blast-furnace practice are now sufficiently complete to allow inferences to be made. The use of fine ores has indicated the manner in which large outputs could be obtained, as it has emphasized the fact that intimacy of contact. between gases and ore, and coke and air, were more important than the time of exposnre. It was reasonable to suppose that if more points of contact were made between the air and the coke, their union would occur in a shorter period of time, and the coke would be burned more rapidly in the same-sized hearth, and an increased output thereby obtained. In consequence of this theory, many furnace men upon relining a furnace increased the number of tuyeres from 8 or 12 to 20, or even more, frequently with unfortunate results. If the number of tuyeres in an old furnace is

Jan 1, 1904

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By George Burke

"Many soil mixing methods have evolved over the years, but the Trench Cutting Re-mixing Deep method (TRD) was developed in Japan, circa 1993, to construct continuous uniform cutoff walls, without the need for an open trench. TRD mixing has been used on over 300 projects in Japan for excavation support, groundwater barriers, liquefaction mitigation, soil improvement and pollution containment. To date, TRD mixing has been used on only three projects in the United States: a test cell in Long Beach, Calif., for seawater intrusion barrier in 2004; a groundwater barrier at a wastewater treatment plant in Lincoln, Calif., in 2005; and presently at Herbert Hoover Dike surrounding Lake Okeechobee in southeastern Florida.The most notable benefits of TRD are its abilities to overcome difficult geology, such as layered rock and dense cobbles and gravels that hinder other soil mixing methods, and to create extremely high-quality walls. The method is ideal for situations in which access precludes the use of more traditional methods due to spoil control, such as waterways and congested urban environments or subsurface obstruction/difficult ground. Spoil disposal is minimized since TRD mixes the soil in place.TRD mixing has a horizontal continuity advantage over traditional multi-auger deep soil mixing (DSM) systems. Because DSM systems create walls by overlapping soil-cement columns, the auger may be deflected by difficult ground, and gaps are possible. Gaps may also occur when constructing an exceptionally deep wall due to the possibility of auger deviation from its required vertical alignment.The method also has a homogeneity advantage in layered soils. Because DSM constructs columns by rotating the defined length mixing tools up and down the soil profile while injecting binder, strength and permeability in each layer will vary. The TRD method vertically mixes the entire profile and core samples show highly uniform strength. It is most cost-effective in deep difficult ground such as layered rock or dense cobbles and gravels."

Jan 1, 2009

By Hélio Wiebeck, Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz

"Natural rubber reinforced commonly with carbon black to produce vulcanized material, turns into a new environmentally friendly nanocomposite when carbon black is replaced by organically modified clays of Brazil. Carbon black is substance derived from the oil refining process with consequent pollution to the environment. Its substitution in this industrial process must contribute to diminish the oil derived products dependence. As the added clays are only a third in weight of the traditionally carbon black added, then, to obtain the same final volume it is necessary to add low cost neutral filler that does not damage the technological characteristics of the final material. This paper presents results using as neutral filler of this type rice husk ashes from industrial wastes. Experiences realized with this nanocomposite material show results of quality and technological characteristics similar or superior to those of the rubber made with carbon black.IntroductionTraditionally rubbers are black or a very dark color. But they can have different appearance when filler of distinct composition of the carbon black is used. The carbon black is substance derived from the oil gotten during the final phases of the mineral fuel treatment with consequent pollution of the environment. Carbon black show nanometric grain sized distribution and a depth black color, because these properties it is also used for computer printers inks production. The substitution of this substance, traditionally used as a reinforced load in the rubber production, will have to contribute in such a way to diminish the dependence of these products as to diminish the pollution of the environment. The present work shows the results of the use of another kind of mineral nanoparticulate material substituting carbon black in the production of some rubber products. This nanoparticulate material is the organic modification of smectite clay treated with some types of ammonium quaternary."

Jan 1, 2008

A typical sub-level block cave mining extraction method employs an undercut level to establish a cavity in hard rock, and as such requires special support methods and products to be installed during the development phase. The undercut level development in the block cave orebody is then sacrificial, and support elements will eventually report to the crusher and perhaps conveyor belt systems for transportation to surface. The choice of support products installed in the undercut level development should take cognizance of the detrimental effect these could have on the mining system such as cutting of conveyor belts, obstructing crushers, safety aspects, and productivity. This work explores the probability and practicality of making use of new-generation support products to make the operation safer as well as enhance productivity in the development phase and during the undercut operation. This paper will investigate the use of glass reinforced plastic(GRP) rockbolts and GRP mesh instead of conventional steel bolts and mesh along with resin capsule-filled holes with the GRP bolts. Complementing this with thin spray liner (TSL) application as another means of creating a safer operating environment, as well as a productive support medium, will also be addressed. These proposed items are envisaged to reduce production downtime and improve the safety of our people. These items are all easy and light to handle, cuttable and crusher friendly, as they will break up during the crushing process.

Jan 1, 2012

By G. Raspa

This article describes a procedure for calculating the recoverable reserves of stratified orebodies characterised by a thin and irregular layers. An application on the phosphate deposits in the N'Zeto region of the Popular Republic of Angola is also described. The procedure consists in building a block model of the deposit through the conditioned multivarial geostatistical simulation of small areal units. The recoverable reserves are then calculated and defined by applying to the model a selection processes based on measured geological/economic parameters taken from the drillholes: thickness of overburden and mineralised layers, economic grain-size fraction, grade. The procedure also takes account both of the geometrical constraints of the mining method and dilution. For reasons of confidentiality, a multiplier has been applied to the values adopted for the sampling data.

Jan 1, 1992

By D. R. Wardrop, P. J. Rowsell, M. D. Waller

D.R. Wardrop agrees that artificial intelligence can contribute significantly to a reduction in both unit and overall well drilling costs but argues for human input to be allowed to overcome the differences encountered on striking the reservoir

Aug 1, 1995

By Andrew Kerr

Abstract - The base-metal and PGE contents of samples from magmatic sulfide mineralization are commonly correlated with their sulfide contents, indicating that the metal contents of bulk sulfides remain approximately constant within a given prospect or part thereof. Calculated sulfide metal contents provide valuable information in mineral exploration and research, but there are few formal descriptions and analyses of the procedures. Sulfide metal contents are best calculated using an assumed value (35.7% S) for a typical pyrrhotite-chalcopyrite-pentlandite mixture, and there appears to be little advantage in accounting for sulfide species separately. Regression of metal data against sulfur is probably the most rigorous approach, but is not always practical. Above 10% S, calculations are very robust, but lower sulfide contents generally demand at least some correction for non-sulfidehosted metals. Such corrections can become significant below 5% S, and/or in olivine-rich samples. They are best accomplished by mass-balance calculations, using concentration data from unmineralized host rocks. Significant uncertainties are introduced by analytical errors for sulfur, base-metals, and PGE, which are commonly measured from separate sample aliquots. These combined errors in sulfide metal contents generally exceed ±10%, but expand further at low S contents. In general, treatment of data from samples containing <2.5% S must be approached with caution, especially for PGE, for which the exact host minerals may not be known. Application of the method in simple grade-potential assessment is straightforward, but research studies involving sulfide-poor samples are inherently more complex. Under-correction or over-correction of data for non-sulfide-hosted metals can lead to false negative or positive correlations between sulfide metal contents and sulfide content. As the latter may itself be linked to geological parameters, such as depth within an intrusive body, undue significance could be ascribed to such trends. There are also valid geological reasons for such correlations, and such data require careful assessment to separate true and artificial variations. Propagated analytical uncertainties increase significantly in sulfide-poor samples, and must also be borne in mind whenever data from different localities or units are compared and contrasted.

Jan 1, 2001

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

By T. Watanabe, M. Nakagawa, K. Kimapong

Ultrasonic wave was irradiated on metal surface in water to introduce compressive residual stress. The ultrasonic wave that was oscillated with 19.5 kHz ultrasonic transducer and amplified with a step type horn was irradiated. Slight plastic deformation occurred at the surface region of pure metal such as Cu and compressive residual stress was introduced. It seemed that the plastically deformed depth from the metal surface corresponded approximately to the depth of introduced residual stress. The higher compressive residual stress could be introduced into the surface of Cu-Zn brass and SUS304 stainless steel because work-hardening was simultaneously induced to those alloys. Furthermore, since martensitic transformation was induced by the plastic deformation in the case of SUS304, the compressive residual stress could be introduced more deeply into the surface region. The residual stress of SUS304 reached to the maximum value of 574 MPa by irradiating for 5min.

Jan 1, 2004

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Aleksander Wrana

"The Carboniferous coal measures, mined across Europe including the major European underground coal mining countries of Poland, UK, Germany, and Czech Republic, suffer from increasing extraction depth. This results in major geomechanics problems associated with ground control and support design.With production being concentrated into ever fewer high performance longwalls, located at greater and greater depth, pressure to ensure the roadways’ functionality (required dimensions) continues to increase. Mining in deeper and more highly stressed mining environments creates several problems. The high stress and deterioration in geological and mining conditions in many cases causes problems with gateroads maintenance (due to excess convergence). That leads to costly production gaps, longwall slowing, transport problems, an increase in the methane hazard and in the general health and safety of the workforce, and deterioration in climatic conditions with major economic risk associated with interruption of the revenue stream. Time—and thus production—delays due to maintenance often result from insufficient geological and geotechnical data acquisition and misinterpretation combined with inadequate support for the type of rock mass.longwall face on the gateroad stability (described by the gateroad convergence, support load, and shape and height of the fractured zone around the longwall gateroad) are presented. The investigations were carried out in the longwall panel with roof caving located at the great depth, in conditions of the Upper Silesian Coal Basin in Poland.The measurement results showed that the gateroad fractures in roof strata began to occur at the distance of about 1000 m ahead of the face. Additionally, the load on support and gateroad convergence increased as the longwall face got closer.It is very important for coal mining research institutes and mine operators to investigate and develop practical solutions and apply innovative support technologies at a great depth (particularly for reinforcement and stabilization of roadways and other openings).Underground measurements of stability conditions around the gateroad is of great importance to mining practice, especially in planning and designing supports for longwall gateroads.The influence of the front abutment pressure results in an increase of support load, gateroad convergence, and shape of fractured rock zone."

Jan 1, 2015

By B. Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to he porous. In- deed, sponge iron, prepared by rcduction of the oxide in a reducing gas, is generally accepted as quite porous. with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig r shows commercial tungsten powder magni- fied at I0,000 X by the electron microscope,&apos; both etched and unetched. In an earlier paper by one of the authors,* the existence of ports in tungsten powder was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these {pores} are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than IOO A. and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1949