Search Documents

By W. H. Bassett

THE subject assigned is rather a broad one but it, is doubtless expected that it will be dealt with as applying to metals and alloys and not to the ob-taining of metals from their ores. The liberty will further be taken of confining the matter discussed to copper and some of the copper alloys. Everyone is familiar with copper, at least everyone who attends the meetings of the A. I. M. E., so no gen-eral description of the metal is necessary. There are still to be recognized two classes of copper and each of these has some sub-divisions. The two general classes are electrolytic and fire-refined copper. Since there is some misunderstanding about these materials, definitions are in order. Electrolytic is just what the name implies. It may and it should be very pure but with high current densi-ties or very impure anodes, or both, impurities such as antimony, tellurium and lead may be carried over to the, cathode. Any one of these, or a combination in which they occur, are alike fatal to good working quali-ties in the resulting metal. Of course, these metals are not supposed to be deposited with copper, but slimes containing them may be 'occluded. in the deposited cop-per or held in rough cathodes if not washed with suffi-cient thoroughness.

Jan 5, 1927

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By J. H. Adkins

The goal of this program was to produce a set of baseline health and safety training materials that could be used by the metal/nonmetal mining industry to reduce injuries and to comply with federal training requirements. The materials developed are arranged in a two level outline format. The first level provides the title, course goals, background and topical outline while the second level provides a detailed outline of the course content. Visuals, designed to portray miners in a positive, attractive fashion, were done in simple line drawing so they would reproduce for handouts without loss of quality. Each of the required units in the Baseline Guides have one or more self-checks. These are designed to be suggestive of evaluation techniques the users can develop for themselves. An instructors guide and a mining terms glossary are included. In a second phase the program developed performance based training guides for Annual Retraining and Experienced New Hires in the Underground Salt Industry.

Jan 1, 1983

By A. B. Holland-Batt

In the 1960s and 1970s, incremental development rather than innovation was the norm for gravity separation. However, the last 15 years have seen a number of new developments in this area. The article reviews the traditional gravity-separation techniques and then examines the newer developments such as centrifugal separators. Emphasis is placed on novel devices or improvements that offer better control or improved performance.

Jan 1, 1998

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By Katsuyasu Sugawara, Takuo Sugawara, Shin-ji Abe, Tadakazu Kagami

"In order to clarify the mechanism and to obtain the fundamental data for heavy metal recovery from an incinerator ash by chlorination, pure chemical reagents, zinc oxide and lead oxide or the fly ash blended with calcium chloride and silicon dioxide were heated up to 1000°C in a nitrogen stream. Thermogravimetric curves of the samples with the chlorinating reagents indicated that solid-liquid reactions accelerated the chlorination and release of metals from the solid phase. The formation of liquid phase of calcium chloride played an important role on effective recovery of zinc and lead at lower temperatures below 800 °C. Although zinc and lead could be decreased in the incinerator ash without chlorinating reagents, addition of chlorinating· reagents enables the removal of metals in high extent· at lower temperature.IntroductionFly ash is discharged about 3,000 tons/day (about 110 million tons/year) from incinerators of municipal solid waste in Japan and mostly fly ash is disposed in landfills. Fly ash includes heavy metals e.g. zinc and lead. Since untreated fly ash caused hazardous leaching problems, Waste Disposal and Public Cleaning Law was revised in 1992, fly ash being designated 'specially controlled' general waste. Fly ash must be disposed by the following suitable, intermediate four methods: [I] Cement- Solidified Method, [2] Immobilized Chemicals Method, [3] Melting Solidified Method, [4] Acid Leaching Method, permitted by the Ministry of Health and Welfare, Japan."

Jan 1, 2000

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By Richard L. Bullock, Bruce Kennedy

Vince Lombardi once said, "Practice doesn't make perfect, perfect practice makes perfect." When it comes to building a mine that will operate at the optimum level for the set of geologic conditions from which it was developed, Lombardi's remark might be paraphrased to describe the problem: planning won't guarantee the best possible mine operation unless it is the best possible mine planning. Any sacrifice in the best possible mine planning introduces the risk that the end results may not reach the optimum mine operation desired. This section addresses many of the factors to be considered in the initial phase of mine planning. These factors have the determining influence on the mining method, the size of the operation, the size of the mine openings, the mine productivity, the mine cost, and, eventually, the economic parameters used to determine whether or not the mineral reserve even should be developed. A little-known fact, even within the metal-mining community, is that room-and-pillar mining accounts for most of the underground mining in the united States. According to a 1973 study on noncoal mining (Anon., 1974), more than 76% of the producing mines [of over 1089 t/d (1200 stpd) capacity] produced approximately 70 000 000 t (77,000,000 st) or 60% of the nation's underground tonnage of material by room-and-pillar mining. That same year, 96.8% of the nation's under- ground coal mines produced 262 950 000 t (289,911,000 st) of coal extracted from room-and-pillar mines (Anon., 1976). Thus, nearly 333 000 000 t (367,000,000 st) of the United States' raw material is produced from mines using some form of the room-and-pillar mining system. Because approximately 90% of all mining in the United States is done by some variation of room-and- pillar mining, it is appropriate to give special emphasis to the effects of the various elements of mine planning on room-and-pillar mining. The relationship of these elements to other mining methods will become apparent as the elements are described in later sections herein. TECHNICAL INFORMATION NEEDED FOR PRELIMINARY MINE PLANNING Assuming that the reserve to be mined has been delineated with diamond-drill holes, the items listed in the following paragraphs need to be established with respect to mine planning for the mineralized material. Geologic and Mineralogic Information The geologic and mineralogic information needed includes the following: 1) The size (length, width, and thickness) of the areas to be mined within the overall area to be considered, including multiple areas, zones, or seams. 2) The dip or plunge of each mineralized zone, area, or seam, noting the maximum depth to be mined. 3) The continuity or discontinuity within each of the mineralized zones. 4) Any swelling or narrowing of each mineralized zone. 5) The sharpness between the grades of mineralized zones within the material considered economically minable. 6) The sharpness between the ore and waste cutoff, including whether this cutoff can be determined by observation or must be determined by assay or some special tool; whether this cutoff also serves as a natural parting resulting in little or no dilution, or whether the break between ore and waste must be induced entirely by the mining method; and whether or not the mineralized zone beyond (above or below) the existing cutoff represents submarginal economic value that may be- come economical at a later time. *7) The distribution of various valuable minerals making up each of the minable areas. 8) The distribution of the various deleterious minerals that may be harmful in processing the valuable mineral. 9) Whether or not the identified valuable minerals are interlocked with other fine-grained mineral or waste material. 10) The presence of alteration zones in both the mineralized and the waste zones. Structural Information (Physical and Chemical) The needed structural information includes the following: * 1 ) The depth of cover. 2) A detailed description of the cover including: the type of cover; * the structural features in relation to the mineralized zone; * the structural features in relation to the proposed mine development; and * the presence of and information about water, gas, or oil that may be encountered. 3) The structure of the host rock (back, floor, hanging wall, footwall, etc.), including: * the type of rock; * the approximate strength or range of strengths; * any noted weakening structures; * any noted zones of inherent high stress; noted zones of alteration; the porosity and permeability; * the presence of any swelling- clay or shale interbedding; the rock quality designation (RQD) throughout the various zones in and around all of the mineralized area to be mined out; the temperature of the zones proposed for mining; and the acid generating nature of the host rock. 4) The structure of the mineralized material, including all of the factors in item 3 plus: * the tendency of the mineral to change character after being broken, i.e., oxidizing, degenerating to all fines, recompacting into a solid mass, becoming fluid, etc.; * the siliceous content of the ore; the fibrous content of the ore; and the acid generating nature of the ore. Economic Information The needed economic information includes: *1) The tons of the mineral reserve at various

Jan 1, 1982

By R. Barthel, O. Nitzsche, J. Pateiro Fernández, T. Cramer

The Hong Gai coal field in northeast Vietnam has been the main coal mining area of Vietnam for more than 150 years. Anthracite coal is produced from several open pit and underground mines situated close to the UNESCO world natural heritage site Ha Long Bay. The mining-induced environmental impacts such as dust emissions, acid mine drainage, and visual impairments due to waste dumps resulted in severe conflicts of interests regarding future land use and the protection of the world natural heritage site Ha Long Bay. Within the RAME project (Research Association Mining and Environment in Vietnam), Brenk Systemplanung is contributing to an improved environmental and sustainable planning in Vietnam's mining industry and the reduction of environmental impacts on Ha Long Bay by developing suitable and sustainable technology and planning measures (e.g. for dump construction/rehabilitation, predictive modelling, and/or monitoring) for Vietnam's leading coal producer.

Jan 1, 2011

By W. A. Gow, J. A. Vezina

"A new process for treating scheelite for the production of tungstic tri-oxide is described. The novelty of the process resides in that an ion-ex-changer is used to convert sodium tungstate to either ammonium tung-state or tungstic acid.The process consists of a conventional hydrochloric acid leach of the scheelite concentrate, and the dissolution of the impure tungstic acid thus produced with sodium hydroxide at pH 8. The sodium tungstate solution is clarified and passed through a column of Dowex 50Wx8 ion-ex-change resin to exchange the sodium ions for either hydrogen or ammonium ions, both being suitable. The tungsten-bearing column effluent is evaporated to crystallize the tungsten as ammonium tungstate; the crystals are washed with nitric acid and water and decomposed by heat to pro-duce tungstic trioxide of high purity.Ninety-six per cent of the tungsten in the concentrate may be re-covered as tungs tic trioxide (W03), and the reagents consumed are 0.7 g HCl, 0.41 g NaOH and either 1.73 g NH.Cl or 225 g HCl per gram of tungsten."

Jan 1, 1966

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

By E. Allen Wendt

It is both a great pleasure and something of a challenge for me to have this opportunity to address a gathering encompassing such a wealth of expertise in the minerals field, It is particularly challenging because I have been asked to turn your attention from the relatively glamorous subjects of gold and money to the more mundane questions of our International commodity policy and the place of buffer stocks in that policy. However, these questions may be of more immediate importance for our economic interests at home and Abroad. I can testify that the problems affecting international commodity markets and the possibility of international action To resolve those problems are matters of real concern to Washington as well as to your industries,

Jan 1, 1978

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By W. Burr Bennett

The prestressed concrete industry in particular, and the precast concrete industry to some extent, are rank newcomers to the concrete construction field compared to the cement, ready-mixed or concrete masonry industries. This young industry reflects its youth and vigor in its enthusiasm, optimism and the belief that it can reach any goal it chooses to set -- and it is setting its sights high. The prestressed and precast concrete industry fully expects to become the major structural and architectural material by the 1980's. Before exploring how the industry expects to reach this goal, a brief look at the origins and the growth of the industry may be useful in an evaluation of the feasibility of this goal. It was always recognized that concrete, strong and efficient for supporting loads which cause compression, was weak and inefficient when used to carry loads which induce tension. Thus the reason for reinforced concrete in which the concrete efficiently carries the compression in a flexural member while low grade steel bars reinforce the concrete in the areas 'of tensile stress. (Fig. 1). The steel being relatively inexpensive, can passively, but quite effectively carry tensile force while the concrete carries compression. The concrete in contact with the reinforcing also protects the steel from corrosion and acts as insulation to provide a superior "built-in" fire resistance. The major disadvantage of reinforced concrete relative to its main competitor, steel, is its weight in relation to its load-carrying capacity. Reinforced concrete systems, such as waffle slabs, I-beams, thin shells, etc. ,

Jan 1, 1971

By L. S. Jeffrey

Estimates for South Africa?s coal recoverable reserves made in 1999range from nine to 59 billion tons; latest estimates by the Minerals Bureau suggest that 33 billion tons is a more likely figure. As much as 70% of that coal is located in the Waterberg, Witbank, and Highveld coalfields, as well as lesser amounts in the Ermelo, Free State and Springbok Flats coalfields. However, the Witbank and Highveld coalfields are approaching exhaustion (estimated 9 billion tons of recoverable coal remaining in each), while the coal quality or mining conditions in the Waterberg, Free State and Springbok Flats coalfields are significant barriers to immediate, conventional exploitation. New extraction technologies, technologies exploiting the energy content of the coal in situ, as well as suitable uses and markets for low-grade, high-ash coal are required before the country can utilize its admittedly vast coal resources. Major challenges for exploiting some Limpopo province coalfields are severe water shortages, insufficiently developed infrastructure, fragile environments and poor roof conditions due to the depth and complex geology. In the Central Basin (Witbank, Highveld and Ermelo coalfields) technical innovations for thin seam extraction, economic mining of both pillar coal and intrusion-fragmented resource blocks and the utilization of lower-grade coals are required. The success of the fluidized bed combustion technology is necessary to utilize the low-grade coals of the Free State and Molteno coalfields, while environmental exemption for past problems, together with strategies for mining small, disjointed thin-seam resource blocks, is required in KwaZulu-Natal. Clean coal technologies, coal cost and quality, environmental considerations, sustainable development, the growth of the South African economy and Government?s regulation of the electricity industry are the main challenges to the continued use of coal as South Africa?s primary energy source.

Jan 1, 2005

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By Manning W. Cox

Van Stone mine area is situated at the head of Onion Creek on the northwest flank of Gillette Mountain, Stevens County, Washington. The di strict was found during World War I, but the mine did not come into production until 1952. Production to the end of 1965 was 2,242,960 tons of ore that yielded 10,700 tons of lead concentrates and 120,000 tons of zinc concentrates. The area is part of the Selkirk Mountains Zinc-Lead Belt, or Kootenay Arc, extending from near Revelstoke, British Columbia, to Colville, Washington. A thick but incomplete section of Paleozoic marine formations occurs in the Kootenay Arc and is overlain by marine and continental Mesozoic formations. Both are invaded by Late Mesozoic-Tertiary batholiths. The belt is characterized by open complex folding and extensive high-angle and local thrust faulting. Principal ore deposits occur in the highly deformed carbonate rocks of Cambrian age-the Maitlen (Laib) and Metaline formations. The Van Stone mine occurs along a steeply S-shaped fold lying between the Kaniksu Batholith on the west and the Rogers Mountain Fault, a northeast-trending fault on the west flank of the Gillette Mountain Anticline, to the southeast. The fold is cut by northeasttrending faults containing notoriously irregular lamprophyric, diabasic, and pebble dikes. The host rocks, lower Paleozoic dolomites, are decolorized, silicified, and silicated in the mine area. Jasperoid and tremolite are the common alteration minerals. Other gangue minerals are barite, pyrite, brucite, calcite, and, near the batholith, pyrrhotite. Ore minerals are galena, jamesonite, and sphalerite. Ore minerals occur in bunches and pods intergrown with tremolite and jasperoid. Zinc is roughly eight times more abundant than lead. The highest ore outcrops at 3870 feet elevation, and an undeterminable portion has been removed by glacial scour. The lowest drill hole penetration has reached 3220 feet elevation. Oxidation ranges up to several hundred feet in depth and may be most closely related to pre-glacial groundwater circulation. The area of the mine was completely over-ridden by Pleistocene continental glaciers, and the present erosion surface is nearly continuously blanketed by up to 150 feet of glacial outwash.

Jan 1, 1968

By H. Akbari

Ordinary portland cement (OPC) is the key pozzalonic component of the concrete mix widely used as a construction material worldwide. B illions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of C O2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic C O2 emissions each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon footprint of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the nonmetallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned extracting some of the valuable metal oxides from fly ash prior to using the major nonmetallic portion of the fly ash for geopolymer concrete application. The results obtained from this study showed that the compressive strength of geopolymer concrete compares favorably with that of conventional concrete prepared using OPC.

Dec 1, 2013