Search Documents

By I KylmSkorpi, H Mansikkaviita

The traditional direct-heated drying process has been replaced by the steam drying process in non-ferrous metal smelters, where steam is available from waste heat boilers. Many recent projects have selected Kumera Steam Dryers in equipping a new production line or modifying an old production line. The industrial performance of the steam dryers has shown significant energy saving and emission reduction. The steam dryers have been operated at high availability and long maintenance interval. As the process principle of Kumera Steam Dryer is different from other equipment, the set-up for steam dryer plants is configured to fit the smelter site and operation conditions to achieve optimal performance. This article discusses the equipment involved in the steam drying process and their combination options.

Jan 1, 2008

By K. Madi, E. Yeugo Fogaing, S. Forest, M. Boussuge, L. Massard, M. Huger, Gaultm C.

This study has been carried out owing to the French research program PROMETHEREF, which aims to improve the knowledge of thermal and mechanical properties of industrial refractories at high temperature. In this frame, this paper relates a collaborative study between Saint-Gobain CREE, R&D Centre for Saint-Gobain Ceramics & Plastics in Europe (Cavaillon), the Materials Center P.M. Fourt of Ecole des Mines de Paris (Evry) and the Research Group on Heterogeneous Materials (GEMH) of ENSCI (Limoges). Data collected at high temperatures by using different means (bending tests, ultrasonic measurements,...) allows the identification of the high temperature behavior of two fused cast materials, produced by Saint-Gobain group for the glass manufacturing industry. The results emphasize the importance of the transformation of zirconia and of the viscosity of the glassy intergranular phase on the mechanical behavior. Damage under the form of microcracking caused by thermal expansion mismatch between the phases is also observed during cooling down at low temperature, when the material is elastic.

Jan 1, 2004

By M. Misra

The finely dispersed kerogen particulates present in the dilute suspension can be coagulated with the aid of a hydrophobic organism, Mycobacterium Dhlei. The initial coagulation and aggregation are strongly dependent on pH and organism concentration, the isoelectric points of oil shale kerogen and Mycobacterium phlei are at pH 3 and 1.8 respectively. As a result the aggregation is rapid around pH 3. Preliminary results show that it is quite possible to use microorganisms for enhanced dewatering of kerogen concentrate produced by froth. flotation.

Jan 1, 1991

By Alfredo Solano R

El presente trabajo señala la geología y estructura del yacimiento minero de Antamina, ubicado en el departamento de Ancash. Para ello, se describe su historia, su geología compuesta por rocas sedimentarias, ígneas, metamórficas; la mineralización, su exploración geofísica, técnicas de exploración y el cálculo de reservas encontradas.

Nov 20, 1978

By Sergio Castro

Los modelos geotécnicos disponibles suelen estar basados en las litologías existentes, sin considerar el impacto de las soluciones hidrotermales en las rocas y, por tanto, en la estabilidad de los taludes de un tajo abierto. El estudio de caso presentado en este artículo muestra que realizar una zonificación en términos de los tipos de alteración hidrotermal es muchas veces necesario; pero también que ello debe acompañarse de investigaciones geotécnicas adicionales y un análisis de la estabilidad física de taludes, con el fin de lograr un rediseño basado en la variabilidad de la resistencia de la roca en cada tipo de alteración, ya que el efecto puede haber sido tan intenso que la roca termina transformándose en un suelo residual.

Jun 30, 2020

By P. Cowx

The carbothermic reduction of zinc oxide rich Electric Arc Furnace baghouse dust in the Tetronics transferred arc plasma furnace to produce a non-toxic slag and a metallic zinc product is described. In particular, the operation of the zinc splash condenser coupled to the plasma furnace is examined and the effect of process variables on zinc recovery is discussed.

Jan 1, 1990

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

"Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, various mines in the Poughkeepsie Gulch and Mineral Point mining districts were examined by C. R. Wilfley, W. R. Hamilton, .and N. E. Wvvlwy, Jr., Bureau Of 'Mines engineers, in July and August 1943, July 1944, and September 1945. In a subsequent report a proposal was made to evaluate this isolated area 'of some 15 square miles located in Ouray and San Juan Counties, Colo.Reconnaissance work in the area was begun in June 1946. Mapping and sampling were begun in July and was completed in Pougkeepsie Gulch and extended westward to include the Hendrick Gulch area of the east side of Ironton Park. Project work was recessed for the winter on October 15, 1946 after approximately 6 square miles of the Poughkeepsie Gulch,district been mapped and 801 samples had been taken.In this report the physical features, climate, and ore deposits districts are described, and a brief history of mining and production lead, zinc; and silver is given.The individual mines and prospects in, the area are described in detail.A list of patented claims and ownerships is given in appendix I, and analyses of samples are tabulated in appendix II.The San Juan preliminary project was directed by Paul T. Allsman, chief, Salt Lake City Branch, Mining Division and was supervised by William M. Traver, Jr., supervising engineer, Colorado Field. Office.Chemical analyses were made by the Salt Lake City laboratory under the direction of H.E. Peterson, chemist, and S. R. Zimmerley, chief, Salt Lake City Branch, Metallurgical Division.Harold A. Waddington, president, Great Divide Mining & Milling Corp., and Ernest Miller, owner, Como Consolidated Mines, were particularly cooperative in making available maps and data concerning their properties."

Sep 1, 1949

By W. A. Tiller, J. P. McHugh

THE phase diagram of the Ge-Te system was first investigated by Klemm and Frischmuth.' They arrived at the phase diagram shown in Fig. 1 indicating the presence of a peritectic phase boundary at the 50 at. pct Ge composition. Later, Schubert and Fricke2 obtained data which suggested to them the possible existence of a eutectic at about 55 at. pct Ge. In order to resolve these differences, we have carefully studied this system in the region 40 to 60 at. pct Ge using both the conventional thermal analysis technique and a new solidification technique.3y4 The alloys were prepared from semiconductor grade germanium and 99.999+ Te by reacting the elements in evacuated, graphite coated, vycor tubes. The samples were placed in a thermal analysis apparatus described elsewhere4 and cooling curves were taken of each alloy to determine the liquidus surface. The cooling curve for a 50 at. pct alloy shows two distinct arrests about 1°C apart which

Jan 1, 1961

By Kathleen M. Kowalski

In emergency management, the effects of stress on the performance of emergency personnel, typically have been ignored or regarded as too enigmatic to quantify. This paper discusses the concept of Critical Incident Stress in responders to emergencies. It presents the rationale for considering stress as a significant factor in the management of emergencies. It is proposed that Critical Incident Stress Debriefing in a disaster can improve the effectiveness of response teams on site, their turnaround time on site, and post-disaster time off the job. Critical Incident Stress intervention also can mitigate potential deleterious emotional effects associated with emergency work. This paper, prepared by a U.S. Bureau of Mines researcher, offers some ideas to the mining industry in general, to mine rescue team trainers, and to developers of program simulations on the specific issue of how people, time, materials and space may be factored into a plan for emergency management. The impact of stress on emergency workers is, presented as a missing component in present emergency management models.

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984

By Verya Nasria, William Bent, William Hogan

"The South Hartford Conveyance and Storage Tunnel (SHCST) project is a significant component of the Hartford Metropolitan District’s (MDC) long-term control plan (LTCP), which is overseen by the Connecticut Department of Energy and Environmental Protection (CTDEEP). This project will address a portion of the MDC’s Clean Water Project (CWP), which will reduce combined sewer overflows (CSOs), eliminate sanitary sewer overflows (SSOs), and reduce nitrogen released into the Connecticut River. The purpose of the SHCST project is to eliminate West Hartford and Newington SSOs, eliminate Franklin area CSOs discharging to Wethersfield Cove and minimize CSO discharges to the South Branch Park River. The locations of each overflow are shown in Fig. 1. In 2010, the district prepared a preliminary design report (PDR) for the SHCST project, which included relief of the Folly Brook trunk sewer and proposed to keep the tunnel boring machine (TBM) retrieval shaft within the city limits of Hartford. Figure 1 shows the 2010 PDR recommended tunnel route. Subsequent to the PDR, the objectives of the SHCST have slightly shifted. In accordance with ongoing revisions to the LTCP, relief of the Folly Brook Trunk Sewer is no longer necessary. Additionally, the MDC has decided to perform less sewer separation in the Franklin Avenue drainage area. To replace the sewer separation, new relief points are proposed within the Franklin area and will be diverted to the SHCST. Figure 1 also shows the current recommended tunnel route (Alignment F). During 2012, the MDC conducted an evaluation of the potential of connecting the proposed North Tunnel (originally proposed as an independent tunnel with its own pump station) into the South Hartford Conveyance and Storage Tunnel. This evaluation concluded that the two proposed tunnels could reasonably be connected together and operated as a single tunnel system utilizing the tunnel pump station at the eastern terminus of the South Hartford Tunnel (Fig. 2). It also was concluded that this alternative was less costly than two independent tunnel systems."

Jan 1, 2014

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By A. F. Lee

A pick-up apparatus capable of yielding quantitative results has been described. Studies of some collector-mineral systems have been presented to illustrate the versatility of the apparatus and prove the validity of results.

By Kalanadh V. S. Sastry, D. W. Fuerstenau

Design and operation of a batch balling drum that can be used easily for experimental investigation of the balling or granulation behavior of particulate materials are described briefly. An experimental procedure for ascertaining the growth kinetics of iron ore concentrates or other particulate materials with this kind of apparatus is outlined.

Jan 1, 1972

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By L. W. Laage

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry for routine ventilation calculations and mine emergency planning. This paper describes recent work by the Bureau and MTU to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1993

By Leland H. Johnson, D. O. Kennedy, John Hyvarenen

"SUMMARYA chronological list of accidents at metal and nonmetal mines and quarries (excluding coal mines) in the United States in which five or more lives were lost has been compiled. Many accidents were described in more detail because of their unusual features. Tables have been included to indicate the number of major disasters and fatalities by the principal product mined, by State, and by 10-year intervals prior to 1945. The number of men employed to indicate man-hours exposed is unavailable; therefore, a true picture of disaster data by principal product mined, by State, and by 10-year intervals is not possible. However, the data are presented to indicate the causes of major accidents and bring to the attention of those affiliated with metal and nonmetal mines and quarries the hazards involved and lessons that can be practiced to keep such accidents at a minimum.INTRODUCTIONThe Bureau of Mines was requested to compile a chronological list of accidents at metal and nonmetal mines and quarries (excluding coal mines) in the United States in which five or more lives were lost. Data have been assembled on accidents from all causes in these mines and quarries from the earliest available information (describ¬ing an underground mine fire in Nevada in 1869) to the last reported major accident (a fire at a company-owned bunkhouse in Arizona in 1945).The accounts of the accidents were taken from articles in the technical press and from published and unpublished reports of the Bureau of Mines. Many of the accidents have been selected for more detailed descriptions because of the unique circumstances and to show the variety of dangers involved.Tables are included to indicate the number of major accidents, with resultant fatalities, by the principal metal and nonmetal producing groups, by State, and by 10-year intervals previous to 1945. The interval 1869-1875 does not cover a 10-year span because of incomplete records previous to 1869.ACKNOWLEDGMENTSThe information contained in this report was obtained from the Engineering and Mining Journal from 1874 to 1947, the Mining and Scientific Press from 1908 through 1922, from various published and unpublished reports of the Bureau of Mines and from reports by State departments of mines. Daniel Harrington, retired chief of the Health and Safety Division; E. H. Denny, supervising engineer, District H; R. M. Loucks, mining engineer; and other engineers of the Division contributed much valuable information and assisted materially in the study."

Apr 1, 1949

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Alfredo Romero Quispe, Carlos Hoffman Sampaio

This work presents a study of characterization of activated carbons for the adsorption of Au(CN)2- complex. A comparative study of six samples of activated carbons, three Brazilian and three produced out of Brazil was made in order to determine their qualification for a performance in adsorption circuits in the extractive metallurgy of gold. The adsorptive capacity and the kinetics of adsorption were compared to the physical and chemical properties of each one. The influence of poluant ions on the kinetics and loading capacity of aurocianyde anion was also determined.

Jan 1, 1995