Search Documents

By H. Jeram

The ilmenite, rutile and zircon processes of the mineral separation plant generate tailing streams, which still contain valuable mineral. This is due to a combination of factors, which include separator equipment efficiency, particle size effects and inefficient operating practices (equipment overloading, blockage, etc.). Recent developments by metallurgical equipment suppliers have led to increased mineral separator performance enabling recovery of previously lost valuable mineral. Mineralogical studies were conducted using QEM*SEM and MLA techniques to identify and quantify gangue mineral species and determine mineral association. Laboratory and pilot-scale test work was then conducted to develop suitable process flowsheets for the recovery of ilmenite, rutile and zircon from current and stockpiled tailings.

Jan 1, 2007

By D. J. Parker, D. Harrington, L. H. Harrison

The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient. points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of, life and damage to property, with special application to the mining industry The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment,, through improved types of lightning arresters,, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures. LIGHTNING PHENOMENA In 1751, Franklin proved that lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition, to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:

By Meyer Steinberg

"Some early experiences of a Cooper Union Chemical Engineer on the Manhattan project and his latest studies on CO2 Greenhouse Gas Mitigation Technologies are presented. Mitigating Global Greenhouse effect while maintaining a fossil fuel economy, requires improving the efficiency of conversion and utilization of fossil fuels, use of high hydrogen content fossil fuels, decarbonization of fossil fuels and sequestration of carbon and CO2 applied to all energy consuming sectors of the economy including electric power generation, materials production, transportation and industrial domestic heating. Decarbonization means removal of carbon as C or CO2 either before or after fossil fuel utilization and sequestration means long term disposal of C or CO2. The review will cover the principles of removal and recovery from power plant, stacks, the oceanographic and geological disposal of CO2 and the conversion of CO2 to gaseous and liquid transportation fuels. The global economic aspects of CO2 mitigation technologies are touched upon.IntroductionThis is an odyssey of a chemical engineer. My career started with the production of U235 at the Gaseous Diffusion Plant in Oak Ridge, Tennessee and the production of PU-239 metal at Los Alamos on the Manhattan Project. After 40 years at Brookhaven National Laboratory, I wound up performing studies on CO2 mitigation technologies. The following is a power point presentation on the subject of global warmingThe DOE is proposing to increase its sequestration development program in order to maintain the utilization of our vast resources in coal both for power and for transportation fuel production. Congress is considering steps to promote energy efficiency in attempts to solve not only the CO2 problem, but also the prime problem of energy supply. We will be promoting increases in energy efficiency as time goes on."

Jan 1, 2008

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985

By Jan D. Miller

The application of computers to the control and study of mineral processing operations such as grinding, classification and flotation has created an interest in simulation studies of these operations with mathematical models. Evidence of this interest is confirmed by papers presented at the 1969 International Computer Application Symposium held concurrently with the Fall Meeting of the Society of Mining Engineers in Salt Lake City, September 17-19, 1969. Proceedings of this symposium, entitled A Decade of Digital Computing in the Mineral Industry. were edited by Alfred Weiss and published by SME. Two sections of this book are devoted to computer application and simulation of mineral processing operations. In the area of comminution, several papers were presented at the International Computer Symposium. The size-discretized batch grinding model was described, and its application to the simulation of batch grinding, locked-cycle grinding and closed circuit grinding were discussed1. Freeh, Horst and Kellner2 approached simulation using a steepest ascent parameter-fitting technique, while Schoner3 considered the dependence of the elements of the mill matrix and classifier matrix on operating conditions, especially the feed rate.

Jan 1, 1970

By S. R. Elliott

THE principles of the caving system, as they apply to mining of soft iron-ore deposits, are well known, as this method has been in use for many years. It is, however, necessary to give a general description of it before describing the Athens method. The shaft and surface equipment should be placed at a sufficient distance from the orebody, so that the caving and pulling of the surface will not disturb the operations of the mine. Levels are started at the proper intervals, and when raises are completed, slicing commences at the top of the orebody and progresses downward. The necessary precautions are taken to avoid the occurrence of large open rooms and it is customary to break sufficient capping to form a mat to prevent heavy falls of ground from crushing through to the lower sublevels and endangering the lives of the workmen. Slicing is continued, and when sufficient width and length are undercut, the capping commences to cave, and in time a settlement occurs at the surface. As soon as this caving commences, the pressure on the timber naturally increases; after it extends to the surface, the amount of pressure has a certain relation to the depth. In other words, the pressure increases with the depth, but not in direct proportion. At great depths, such as that found at the Athens, 2500 ft. (760 m.), the pressure might be so excessive that the cost of keeping working places open would be prohibitive. The actual caving of the surface in a deep mine, with a great thickness of capping, is slow and often takes years to accomplish. After sufficient width and depth -have been undercut, the capping starts to break away, but through arching large masses of rock-.fill the opening, support the capping, and retard the continuation of caving. Caving to the surface is, therefore, retarded until either a sufficient thickness of the orebody is removed, or the width and length of the undercut part have been greatly increased. I wish to emphasize this fact of slow caving, for it is on, this principle that the success of the Athens system. largely depends.

Jan 8, 1920

By Q Zhou, G Barrett, Y Choi, J Jiang

As part of a general review of processing double refractory ores through Barrick GoldÆs autoclaves /carbon-in-leach (CIL) facility at Goldstrike, a study was made to evaluate the use of surfactants for reducing the loss of gold during cyanide leaching of preg-robbing gold ores. Consistent improvement of gold recovery was observed with surfactants at various testing conditions. This paper will discuss the results obtained from laboratory and pilot-scale testing, as well as, review potential mechanisms for the observed improvement in gold recovery.CITATION:Zhou, Q, Barrett, G, Jiang, J and Choi, Y, 2013. Surfactants for gold recovery improvement with preg-robbing gold ores, in Proceedings World Gold 2013 , pp 367-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P. Shahinian, J. Weertman

Minimum creep rates of nickel samples were measured in the stress region of 2.5x107 to 2.8xl0 dyne per sq cm and the temperature region of 400° to 1100°C. The creep rate seems to be proportional to (stress) at stresses below 7x10H dyne per sq cm. The activation energy of creep is approximately 65,000 cal per mol. IN a recent theory' of steady-state creep which is based on Mott's dislocation climb mechanism, the following creep equation was derived for creep in polycrystalline metals (if where K is creep rate, Q the activation energy of self-diffusion, S the entropy of activation of self-diffusion, L' the grain size, L the subgrain size, b the length of the Burgers' vector of a dislocation, u the shear modulus, u the stress, a the critical shear stress, M the density of active Frank-Read sources, v the vibrational frequency of a vacancy, and kT has its usual meaning. This equation predicts a creep rate which depends on the stress through a power law at low stresses. At high stresses the creep rate increases much more rapidly with stress. The theory breaks down for stresses great enough that the inequality holds true. It was the purpose of the present in-

Jan 1, 1957

By Jeran Paul W., Michael A. Trevits

Subsidence data gathered by the U.S. Bureau of Mines over a series of longwall panels in the Pittsburgh Coalbed were studied to obtain insight as to the role of time in the subsidence process. It was found that subsidence began essentially with undermining and was completed within 1 year. The progress of the subsidence was dependent upon location above the panel. Subsidence in the central area of the subsidence trough, where subsidence is the greatest, was about 90 pct complete by the time the face had progressed a distance equal to one overburden thickness beyond a particular surface point. For a point over the rib of the longwall panel, the subsidence was only about 60 pct complete at this time. Data from three other sites in the northern Appalachian Coal Basin were analyzed to determine if an anomaly or the true characteristics of the subsidence process had been observed. All sites behaved similarly in the central portion of the subsidence trough. However, the subsidence of points over and adjacent to the ribs of the longwall panels was site specific. The fact that movement across the width of the panel was not uniform should be taken into account in assessing damages or the potential for damages resulting from mining-induced subsidence.

Jan 1, 1995

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

[Participating Scholarship Colleges and Universities 136 Big Sky Coal Company 111 Canyon Fuel Company LLC 97 Coal Age Magazine 109 Commercial Testing & Eng. Co 99 Continental Conveyor & Equip. Co 103 Copper Mountain Resort 128 Dakota Coal Co 100 DBT America Inc 117 Empire Machinery 101 Energy West Mining Co 102]

Jan 1, 2001

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By A. M. Dale, J. Standeven, B. Evanoff

Tool manufacturers continue to incorporate new designs to the internal mechanism of tools in order to decrease the vibration that is delivered to the hand during operation. Modification of some tools to minimize tool vibration is not easily resolved through internal tool design. For this reason, vibration damping materials applied between the tool and the hand are a simple alternative. The damping materials may be applied to the area of the tool directly contacted by the operator or in a glove containing a vibration absorbing pad. These interventions are developed specifically to damp vibration but are not necessarily produced and tested under the same work conditions that a company may expose their workers. Therefore, it is important to test the value of the proposed interventions for the specific applications. This study evaluates the effectiveness of anti-vibration interventions currently in use at a local manufacturing company. Methods The design of this study evaluates the vibration energy produced at the tool handle and from the back of the operator’s hand. Each operator performed a series of fastener installations in metal using several interventions and one series with no intervention as a control. Four of the interventions were gloves containing anti-vibration material and the fifth intervention was an anti-vibration material wrapped around the tool handle. The protocol for wrapping the tool handle was developed and is part of the equipment procedure at this manufacturing company. Test conditions mimicked production work conditions including similar materials, fasteners and technique for installation. Vibration values were collected using 3 tri-axial accelerometers with one firmly glued to the tool handle close the hand grip as recommended by ISO 5349. A second accelerometer was placed on the top of the pistol shaped tool. The third accelerometer was attached to the back of the hand close to the third knuckle using double sided tape. Results Preliminary results for 3 volunteers show a difference between the vibration values of the control condition (mean hand vibration on bare hand = 1.77 Gs) compared to all of the interventions (p=.0001 using Mixed Procedure, Tests of Fixed Effects). The graph below shows individual trials for each subject for each condition. Glove 3 with the air bladder insert shows large variability between subjects (Range = 0.84-3.33 Gs). The other interventions show much less variability both within subjects and between subjects indicating consistent response with use of the intervention.

Jan 6, 2006

By Robert E. Green, Edmund G. Henneke

The velocities of the three possible modes of elastic wave propagation have been calculated for single-crystal copper at 1-deg intervals throughout the standard stereographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy flux and specimen axes are presented as arrows drawn on stereographic projections. The orientation factors associated with dislocation motion on the primary slip system only and also on all twelve slip systems have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing wave resonant specimen have also been calculated. The results of these calculatians are compared with earlier calculations on aluminum crystals and the relevance of these results to ultrasonic attenuation measurements is discussed. GREEN and inton' have recently outlined a procedure for determining the orientation factors for dislocation damping in single crystals. The stress field associated with a given mode of elastic wave propagation is resolved on the slip systems in which it is assumed the dislocations are vibrating due to this stress field. Since, at room temperature, slip has been observed on a limited number of systems in fcc and hcp metal crystals, it is assumed that these systems are the appropriate ones to use for the resolving process. This procedure has been applied to aluminum crystals by Hinton and hreen' and to zinc crystals by Henneke and Green.3 In the present paper the modes of elastic wave propagation have been calculated for copper crystals possessing orientations at 1-deg intervals throughout the standard stereographic triangle. The deviation of the energy flux vectors from the specimen axis have been calculated for each mode. The stress field associated with each mode has been resolved on the (111)(110) slip systems in order to determine the orientation factors for dislocation damping. MODES OF ELASTIC WAVE PROPAGATION For any direction in a linear homogeneous aniso-tropic material three elastic modes can be propagated. In general, each of these modes has both longitudinal and transverse particle displacements associated with it and thus are not "pure" modes. However, there is always one component which is greatest in either a longitudinal or transverse direction and hence the mode may be referred to as quasi-longitudinal or quasi-transverse, accordingly. For certain axes of high symmetry pure modes may be propagated. The phenomenon of refraction of the energy flux vector is also exhibited by elastic wave propagation in ani-

Jan 1, 1969

By John A. Johnson

Conclusions regarding the use or omission of stemming in blasting have not peen reached, pending completion of all aspects of this investigation. The results from the dust phase of this study on six classes of stemming prove that the kind of stemming affects the amount of dust produced from blasting. In previous work at the Mount Weather testing adit it was demonstrated that blasting produces the highest dust concentrations of any of the mining processes.5/ Under the conditions prevailing at the Mount Weather testing adit, the average of all rounds having a break of at least 95 percent showed that the least amount of dust was produced when no stemming was used.

Jan 1, 1940

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By Bert Bahnson

As farms decrease and subdivisions increase there is a continuing demand for easy and safe silo removal. A few years ago I attended one of the Omni istribution explosive classes and was impressed by a product designed by Omni owner Bill Nixon called the Omni Breach. Its original purpose and main current use is law enforcement; specifically door breaching and tactical operations, with most of the force coming from water using a minimal amount of explosive component. I experimented with various charge strengths on concrete and found that it can be easily shattered with little flyrock or airblast. A neighbor of mine had an old silo within a foot of a barn that he was rebuilding and inquired about its removal. His property was sandwiched between an elementary school and Interstate 40, so I told him that I would do some test shots and if the results proved satisfactory, I would take the job for free to test the following theory.

Jan 1, 2006