Search Documents

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By G. M. L. Robinson

The Clean Water Act, as administered by the Environmental Protection Agency, has mandated industry, government and the public to comply with potentially conflicting and vague water quality statutes, regulations and guidelines. Universal regulatory strategies have been developed which have introduced and have created regulatory, compliance and institutional conflicts. Conflicts have been created because National water quality performance goals and design standards are vague, and, in many cases, cannot be scientifically justified. Because of regulatory technical requirements to define background and environmentally impacted water quality characteristics, the ability to achieve regulatory compliance is difficult. Difficult issues requiring resolutions includes but are not limited to site specific surface and ground water quality classification systems, water quality standards and guidelines, point and non point pollution sources etc. Because of these statutory and regulatory complexities, a confrontational regulatory system has been created as it relates to: - defining performance criteria in relation to design criteria; - resolving water quality statistical compliance conflicts; - defining laboratory precision requirements; - determining background groundwater characteristics; and - locating a representative point of compliance. Because of these complex regulatory issues, the ability to balance goals, needs and economics has not been achieved or in many cases has not been attempted, without legal intervention. A few examples illustrating where water and waste management compliance conflicts have been experienced.

Jan 1, 1992

By Ann M. Hagni

Flash reduction of zinc oxides is an alternative, environmentally safe method to leaching and electrowinning for zinc recovery. Zinc and lead are volatilized in a flash reactor, a non-hazardous residue is generated, and the fuel source is inexpensive coal in the flash reduction process. Results from experimental laboratory tests yielded low zinc recovery for this process. Mineralogical and textural characterization of the residues from the flash reduction tests for different feed materials and temperatures were conducted to determine the cause for the low zinc recovery. Reflected light microscopy, cathodoluminescence microscopy, scanning electron microscopy-energy dispersive spectroscopy, and X-ray diffraction were utilized in this applied mineralogical research. The original zinc calcine is composed primarily of fine-grained, iron-bearing zincite particles, 25-40 um in diameter, in a porous texture. Pellets processed at 1150°C were found to produce reaction rims of franklinite-magnetite-jacobsite solid solution that are 125-200 um thick and surround cores of unreacted iron-bearing zincite in a Zn-Fe-Si-Ca glass matrix. The reaction rims have subsequently oxidized to form an outer 10 ~m thick rim of hematite. Slags from calcines processed at 1275°C are primarily triangular particles with porous centers, cenospheres, and spheres of iron-bearing zincite, in addition to rectangular particles composed of non-porous franklinite-magnetite solid solution cores with iron-bearing zincite rims. Slag particles from calcine processed at 1200°C are predominantly 100-250 ~m triangular-shaped, spheres, and cenospheres containing fine-grained franklinite and franklinite-magnetite solid solution in an iron-bearing zincite matrix. Slag from calcine processed at 1300°C are also predominantly 1 00-250 um triangular-shaped, spheres, and cenospheres but contain coarser-grained iron-bearing zincite. The zincite in the penets and the slags typically contain 10-20% iron. Based upon these mineralogical observations, it is concluded that the significant amounts of iron in the zincite prevent volatilization of the zinc in the flash reduction process.

Jan 1, 1995

By Akira Usui, James R. Hein, Rachel Dunham

Ferromanganese crusts are found on most hard-rock substrates in the deep ocean (800-3,000 m). Their distributions on seamounts are complex and controlled by a wide-variety of factors including seamount morphology, current patterns, mass wasting, substrate rock type and age, subsidence history, and others. However, the development of this potential resource ultimately depends on this distribution, as well as on the small-scale topography, grade, and tonnage. The parameters that will ultimately be used to define a mine site are unknown, but reasonable assumptions based on 25 years of data collection can be used to bracket likely permissive characteristics.

Vertical retreat open stoping (VROS) is a variation of sublevel open stoping (SLOS) that has been introduced at Cannington to minimise the influence of subvertical geological structures during stope extraction. The first application of VROS is described, where structures within the stope resulted in a change in firing sequence and the extraction of two complete sublevels in a single blast. The use of electronic detonators is critical to the success of VROS and their application is described. Numerous benefits of using VROS have been identified and are described. To date, eight stopes have been successfully mined using VROS. In addition to the first application of VROS, two further case studies are described.

Jan 1, 2005

By Robert Mehl

THE mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystalline symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray .technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by-slip along atomic planes.1 This slip may be inhibited in a number of ways: by the interatomic forces of cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by lattice distortion caused by solid ,solution formation or by mechanical strain; by the intercrystalline boundaries where slip is restrained by the non-registration of the atom planes in adjacent crystallites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.3 In pure metals, and perhaps also in solid solutions, the atom planes, of easiest slip are those exhibiting the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be predicted from the analysis of the lattices. Concerning the interatornic forces, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bot-tone,5 correlate the hardness of the pure metals with the atomic volume;.

Jan 1, 1928

By O. A. Ogunseitan

The contamination of aquatic ecosystems by mercury wastes is one of the most serious forms of environmental pollution associated with the metal mining and electrochemical industries. The transformation of inorganic mercury to alkylated species is a reversible bacterially-mediated process. The production of methylated mercury is of ?major public health and eco-toxicological concern because these forms of mercury are highly toxic ?and they bioaccumulate in aquatic organisms. We determined the response of the genetic determinants of mei:cury transrormation by Pseudomonas species (that predominate in contaminated soils and sediments), to the concentration and species? or available mercurfiations. By combining selective isolation and gene. ?probe techniques, the intrinsic genetic potential for mercury detoxification in a contaminated environment ?can be estimated. We determined that genetic units required for mericury volatilization (merA ?for mercuric reductase) are naturally amplified in response to mercury. Mercury-resistant bacteria that tolerate up to 100 ug Hg(Il)/ml of medium contain about 10 times more DNA fragments encoding merA than in unadapted bacteria. The exposure of bacteria to methylated.Hg (10 ug/ml lake water) produced increases (up to 10 times) in .genetic units, and higher levels of genetic expression (up to 50 times) per ml of lake water for the mercury reductase system, than on-induced lake water. The findings suggest that in environments where methylated Hg may accumulate as a result of bacterial activity, the reverse reaction which leads to the removal of mercury through volatilization from the system, may be achieved by inducing genetic ?amplification and expression of the mercuric reductase gene system.

Jan 1, 1991

By C. W. Schultz

The distribution of material passing a screen, or a set of screens, is described by the equation [ ] where p = the probability that a single particle will pass the screen on a single presentation k = number of layers of screen cloth n = distance from head of screen expressed as number of screen openings. This model can be used to predict the performance of conventional screening operations (i.e., k = 1) as well as the so-called "statistical screening" operations. Using this technique, in which multiple identical layers of screen cloth are employed, screening can be carried out at a finer size than is possible with conventional techniques with no loss of separation efficiency.

Jan 1, 1969

Strain-Hardening Exponent of Cross-Rolled Beryllium Sheet by S. R. Maloff, Vol. 215, No. 5, page 872, was omitted from Table of Contents for the October issue. Stabilization Phenomena in Beta Phase Au-Cd Alloys by Howard Birnbaum, Vol. 215, No. 5, page 786. The figure denoted Fig. 1 should be Fig. 3, Fig. 3 should be Fig. 4 and Fig. 4 should be Fig. 1. The captions are in the proper sequence. Activity of Carbon in Liquid Iron Alloys by Tasuku Fuwa and John Chipman, Vol. 215, No. 4, page 708. First equation, right hand column, page 710 should read

Jan 1, 1960

By H. C. de Wet

The predevelopment and preparation of a total infrastructure in a deep level mining environment, prior to the shaft system being commissioned has major advantages. This paper intends to indicate these advantages and outline an understanding of the disadvantages. These benefits can be classified in three basic groups: the financial and timing advantages, a knowledge of the ore body and the development of required technology to meet the design parameters. The required technology in many aspects was still to be developed prior to successful application. Stemming from the technological evolution are some secondary advantages which will be described in each of the groups. Safety and health considerations and some practicalities made some of the new technology redundant prior to the actual application. In each case the actual achievements and the anticipated benefits will be indicated to allow the reader to distinguish clearly between planned and actual achieved advantages.

Jan 1, 1997

By Pinnaduwa H. S. W. Kulatilake, Biao Shu

The intact rock properties and discontinuity properties for both Devonian Rodeo Creek (DRC) and Devonian Papovich (DP) rock formations that exist in the selected open-pit mine were determined from tests conducted on rock samples. Special survey equipment, which has a total station, laser scanner and a camera, was used to perform remote fracture mapping in the research area. From remote fracture mapping data, the fracture orientation, spacing and density were calculated using more refined procedures compared to what exist in the literature. Discontinuity orientation distributions obtained through remote fracture mapping agreed very well with the results of manual fracture mapping conducted by the mining company. The GSI rock quality system and Hoek-Brown failure criteria were used to estimate the rock mass properties combining the fracture mapping results with laboratory test results of intact rock samples. Fault properties and the DRC-DP contact properties were estimated based on the laboratory discontinuity test results. A geological model was built in a 3DEC model including all the major faults, DRC-DP contact and two stages of rock excavation. The built major discontinuity system of 44 faults in 3DEC with their real orientations, locations and three-dimensional extensions were validated successfully using the fault geometry data provided by the mining company using seven cross-sections. Numerical modeling was conducted to study the effect of boundary conditions and lateral stress ratio on the stability of the considered rock slope. For the considered section of the rock slope, the displacements obtained through stress boundary conditions seemed more realistic than those obtained through zero velocity boundary conditions (on all four lateral faces). Stable deformation distributions were obtained for k0 in the range of 0.4 to 0.7. Because the studied rock mass is quite stable, it seems that an appropriate range for k0 for this rock mass is between 0.4 and 0.7. The displacements occurred between July 2011 and July 2012 due to the nearby rock mass excavation that took place during the same period; they were compared between the field monitoring results available from the mining company and the predicted numerical modeling results and a good agreement was obtained. Overall, the successful simulation of the rock excavation during a certain time period indicated the possibility of using the procedure developed in this study to investigate rock slope stability with respect to expected future rock excavations in mine planning.

Jan 1, 2015

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

A GREAT and incomparable speculation is whether the discovery of A compounding the powder used for guns came to its first inventor from the demons or by chance. With this invention he certainly far surpassed all men of every age from the creation of the world up to that day when it was announced by him-men so very learned, indeed like angels and of divine intellect, powerful in every knowledge and power. These had not only revived-arts and sciences and discovered new ones with their intellects, but they had information about all natural

Jan 1, 1942

By Shawn Benner, David Blowes, Carol Ptacek

A full-scale reactive barrier was installed into an aquifer impacted by acid mine drainage in August 1995 at the Nickel Rim mine site near Sudbury, Ontario. The primary mechanism of water quality improvement is bacterially mediated sulfate reduction and metal sulfide precipitation. Dramatic changes in the groundwater chemistry are observed with up to 90% decline in Fe (from >18 to <2 mmol L-1) and increases in alkalinity from <1 to >10 mmol L-1 (as CaCO3). Over a 3 year period, the rate of Fe removal declines by approximately 35%. Primary controls on barrier performance are organic carbon reactivity, groundwater temperature, and variable residence time within the barrier.

Jan 1, 2000

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

Environmental management of minesites in general, and management of water discharges in particular, is receiving ever-increasing attention. One key component in the successful design and operation of water management systems is to address the presence of sediment in the water being conveyed. Sediment erosion in the mining environment is often greatly exacerbated by disturbing the ground surface of vast areas of catchment. If sediment avoidance, transport, deposition or release are not adequately addressed, the impact on water management facilities can include loss of storage and hydraulic capacity, more frequent equipment replacement, increased operational costs and potentially environmentally unacceptable sediment discharges to receiving waters. An overview of sediment management within water facilities is presented here, and design of one particular approach, the use of settling basins for sediment removal, is discussed in detail. Examples are used to illustrate lessons learnt where particular approaches to sediment management have been found to be lacking. The common themes in the lessons learnt include the need to characterise hydrodynamic conditions and sediment properties in the water source, to set performance targets for sediment management, and to develop operating procedures to meet these targets under a realistic range of scenarios. The examples show how analysis of expected performance of sediment management can help with planning of operation and maintenance strategies. For settling basins, use of a simulation model that includes the effects of turbulence on settling can provide considerable benefits in optimising basin design and evaluating performance. Even in the most basic approach to sediment settling, establishing performance targets based on design flow and sediment characteristics is critical.

Jan 1, 2003

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at the Institute headquarters during the period Oct. 10; 1916 to Nov. 10, 1916. Edwin C. Bloomfield, Montreal. Roy E. Hoffman, Hannibal Mo. A. H. Collbran, Seoul, Korea. E. C. Harder, Cienfuegos, Cuba. Eugene Coste, Calgary, Canada. B. Jaeger, London, England. Fred Crabtree, Pittsburgh, Pa. Herbert H. Lauer, Philadelphia, Pa. P. St. John Dixon, London, England. Frank C. Laurie, Los Angeles, Cal. A. E. Drucker, London, England. 0. T. Lempriere, Melbourne, Australia. F. N. Flynn, Clifton, Ariz. W. C. Phalen, Washington D. C. Justice Grugan, Edwards, N. Y. William H. Rea, Pittsburgh, Pa. Fred A. Hale, Jr., Goodsprings, Nev. Thor Warner, Kingman, Ariz. P. S. Haury, Seoul, Korea. Arthur P. Allen has resigned his position with the Calumet & Hecla and is now connected with the Highland Mining Co., Ashcroft, B. C., Canada. H. Foster Bain, editor of the Mining Magazine of London, has resigned his position.

Jan 12, 1916

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By N. A. Duke, R. L. Carpenter

Abstract - The West Meliadine area is underlain by structurally interleaved panels of mafic and minor ultramafic metavolcanic rocks and metasedimentary rocks that occur along the northern margin of the Neoarchean Rankin Inlet greenstone belt. Three structural and metamorphic domains are recognized: (1) the easterly Wesmeg domain; (2) the central Barracuda-Ridge domain; and (3) the westerly Peter Lake domain. The Wesmeg domain is characterized by a series of southeast-trending, north-dipping, foliation-parallel panels of greenschist facies mafic metavolcanic and metasedimentary rocks. The Barracuda-Ridge domain is comprised of greenschist to amphibolite facies mafic metavolcanic rocks that define an east-northeast-trending structural grain. The Peter Lake domain consists of amphibolite facies mafic metavolcanic rocks and minor metasedimentary rocks intruded by a monzonite pluton. West Meliadine hosts the economically significant Wesmeg gold deposits, as well as other important gold showings across the Barracuda-Ridge and Peter Lake domains. The geological setting of the Wesmeg gold deposits resembles that of a break or fault zone. The Pyke Break is a major geophysical discontinuity (>65-km strike length) and is the first-order structural control on gold mineralization at West Meliadine. It is several kilometers wide and characterized by polyphase deformation and shear zone development accompanied by lode-gold mineralization. In general, gold concentration is related to quartz and iron-carbonate veining, iron sulfides (mainly arsenopyrite and pyrrhotite), and accompanying silicate alteration minerals that overprint favorable chemical and structural traps late in the history of deformation.

Jan 1, 2004