Search Documents

By W. C. Meyer, R. R. Klimpel

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering mathematical models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and model predictions are presented.

Jan 1, 1984

By W. W. Roepke

One phase of Bureau of Mines research deals with reduction of primly respirable dust generated by bit cutting action at a coal seam face. This paper presents a summary of coal cutting technology addressing this problem. All aspects of the cutting system affecting miner health and safety are discussed. Cutting design concepts are considered that minimize dust generation, energy used, and Ignitions, while maintaining production. With present equipment, an operator can maintain production and minimize dust energy and conditions by cutting at maximum depth (maximum sumping or advance rate) at all times, at minimum rpm with fewest possible bits, and with lowest possible included bit tip angle, i.e., minimum bit wear.

Jan 1, 1985

By M. J. Little

Potgietersrust Platinums Ltd is Anglo Platinum?s only open pit operation and annually extracts 57 million tonnes of rock from 2 open pits. Over the past 3 years ~220 km of exploration drilling has been done, ~1000 km of rock face have been exposed for face mapping and over 7000 laboratory and field tests have been conducted. This has produced large amounts of geotechnical data to be utilised for feasibility studies, initial slope design and ongoing slope optimisation. It was necessary therefore to develop geotechnical databases to manage the vast amounts of data collected. SABLE and MineMapper 3D databases were created for logging and mapping respectively, with rock testing data incorporated into both. A pit inspections database was developed in MS Access and the existing groundwater and slope monitoring database was improved. The databases were linked to AutoCAD and Datamine to ensure that the latest geotechnical data is used for planning, draughting and modelling. The use of geotechnical databases ensures that no data is lost, standards are maintained and analysis can be easily performed. This increases the confidence of the analysis and allows the geotechnical engineers to optimise slope designs and blast designs on a regular basis. This reduces the risk of slope failure thus making the open pits more economical and safe.

Jan 1, 2006

By Jackson G. Jenkins

Magma Copper Company's San Manuel SX-EW facility has operated since May, 1986. The original facility had a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solution from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing in-situ leach solutions. This paper focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research utilizing surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1993

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

By R. N. Rothan, V. Khunova, C. M. Liauw, G. C. Lees

The interphase modification activity of 1,3-phenylene dimaleimide (also known as m-phenylene bismaleimide (BMI)) has been studied in composites based on magnesium hydroxide (60% w/w) and a polypropylene block copolymer (PPBC) that featured an ethylene-rich elastomeric impact modifier phase. BMI was found to be a unique product that led to significant simultaneous improvements in composite strength and toughness, even at the high filler levels. BMI modification was found to promote encapsulation of filler particles with the elastomeric phase of the PPBC together with formation of a PP boundary layer of increased crystalline content.

Jan 1, 2003

By J. A. C. Diering

All underground openings are three-dimensional, and in many cases it is not valid to analyse two-dimensional sections. This has been a problem in the past owing to the magnitude and complexity of three-dimensional stress analysis. In this paper a three-dimensional boundary element approach, using non-conforming quadratic elements, which is specifically applicable to underground excavations, is described. In addition, the philosophy of application of stress analyses is discussed. Three case histories are presented to demonstrate the practical nature of the approach as a tool in solving mining problems.

Jan 1, 1987

By J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. -- Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing.

Jan 6, 1953

By J. D. Mc Beth

The Carlin Gold Mining Company, a wholly owned subsidiary of Newmont Mining Corporation has been successfully operating an open pit gold mine and cyanide mill for approximately the past ten years. It is a unique operation in that about 20 percent of the mill feed is a carbonaceous ore refractory to cyanidation that must undergo a pretreatment stage developed for, and by, Carlin. The mine and plant are located in the Tuscarora mountain range is north-eastern Nevada near the towns of Carlin and Elko. Claims were staked at the minesite in 1961 and 1962. A drilling program was initiated late in 1962 and after drilling a total of 250,000 feet of rotary drill holes an estimated 9,300,000 tons of ore at a grade of 0.32 ounces of gold per ton was delineated.

Jan 1, 1975

By Derek. C. Arnold

In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir. In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir.

Jan 1, 1999

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

Jan 1, 1950

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By J. J. Gilman

THEORIES of fracture in metals have been based primarily on the dependence of fracture strength on grain size. This dependence was first observed by Masing and Polanyi.l These workers, as well as 0rowan12 and Davidenkov and Wittman,' thought the grain size could be equated with the crack size in the Griffith condition for crack propagation.4 In this way they could account for the observed proportionality between fracture stress and the reciprocal square root of the grain size. The chief results of recent investigations of the fracture strength of polycrystals are summarized in Fig. 1. Low for iron,5 Petch for iron,' Greenwood and Quarrel for zinc, Petch and Zein for zinc,' and Hauser, Landon, and Dorn for magnesium'' have all found that the fracture stress of a polycrystal is proportional to the reciprocal square root of the grain size. Also, they find that, for large grain sizes, the fracture stress lies near the extrapolation of the yield-stress curve determined at small grain sizes; where measurable plastic strain precedes fracture. Low9 has gone a step further and shown that, in Range 1, the fracture stress in tension is almost identical to the yield stress in compression for a given grain size. Homes and Gouzou, 10 and Low also have shown that, in Range 2 of Fig. 1, microcracks form when the yield stress is reached, but they do not cause failure until the stress reaches a much higher value. The fact that yielding always precedes fracture suggests that fracture is induced by plastic flow. A mechanism by which this might occur was first proposed by Zener.11 He pointed out that blocked dislocations would cause stress concentrations which might cause fracture. The blocking would be caused by grain boundaries. This idea has been developed by Eshelby, Frank, and Nabarro,12 by Koehler,13 and by Stroh.14 By means of etchpits blocked dislocations have been observed in brass by Jacquet,15 in zinc by Gilman,16 and in lithium fluoride by Gilman and johnston. The blocked-dislocation theory and the experiments that bear on it have been summarized by Mott.18 One of the strong points of the blocked-dislocation theory is that it can explain the grain-size dependence of the fracture stress in a natural way. However, Low9 has pointed out that the theory is not satisfying when it is considered quantitatively. Gilman10 also has criticized the theory and presented an alternative interpretation of the relation between fracture stress and grain size. Since the blocked-dislocation theory is not the only theory that can explain in the grain-size effect, it is necessary to find other evidence either to support or deny it. In this investigation the following points were studied: 1) If blocked dislocations normally cause fracture, then the fracture stress ought to be very high in the absence of plastic glide. Is it? 2) If dislocations must be blocked in order for metals to fracture, then certain types of grain

Jan 1, 1959

By C. A. C. Sequeira, G. N. Anastassakis

Electrochemical processes occur on nano-, micro- and macro- scale in numerous applications such as fuel cells, batteries, hydrogen production, mineral extraction, water treatment, electrotherapy, sensors and many others. In most of these applications, gases evolve either at one or both electrodes due to electrolysis. These gases form bubbles play a crucial role in electrochemical systems. For example, in electrowinning (EW) that is used to extract and refine metals such as Cu, Zn, Ni, Mn, and Cd from their solutions, in most cases the solution is acidic and oxidation of water molecules at the anode is the common counter reaction, which results in the liberation of oxygen bubbles. This generally requires a high overpotential and accounts for a considerable percentage of the energy consumed in metal EW electrolytic cells, apart from producing acid mist that is very corrosive for other cell equipment and building structures. The behaviour of bubbles in electrochemical systems is still a complex challenging topic which requires a better understanding of gas bubbles hydrodynamics and their interactions with electrode surface and bulk liquid, as well as between the bubbles themselves. The objective of the current paper is to briefly review the fundamental hydrodynamics of both gas bubbles on the electrode surface and gas bubbles interaction with the liquid bulk solution. The current work also investigates the impact of gas bubbling and some operating parameters in copper EW, such as current density (100-500 A/m2), temperature (25-75ºC), acidity (50-300 g/L) and a typical chemical mist suppressant (<50 ppm). The results clearly show that both suppressant and temperature reduced the overall surface tension of the solution. Also, chloride concentration and applied current improved electrolyte flow and copper quality at higher current densities. The current paper contributes to the development of mineral processing (specifically to copper hydrometallurgy), as it deals with fundamental hydrodynamics and interactions of gas bubbles that formed during copper EW and play a crucial role in copper electrochemical systems.

Jan 1, 2018

Taking advantage of the lessons in administrative organizations which were taught by the war, Director Van H. Manning has put into effect a new form of organization in the Bureau of Mines. The Bureau is divided into two branches, one the investigations branch and the other the operations branch. F. G. Cottrell, who has been chief metallurgist of the Bureau, has been promoted to the position of assistant director and will be in charge of the investigations branch. F. J. Bailey, who has been chief clerk of the Bureau, has been placed in charge of the operations branch with the title of, assistant to the director. All research and technical control will be exercised through the investigations branch, while the non-technical work, administrative duties, and dissemination of the results of the Bureau&apos;s activities will be handled by the operations branch. Under the investigations branch comes the division of mineral technology, in charge of Dr. C. E. Parsons; the division of fuels, under the chief mechanical engineer, 0. P. Hood; the division of mining, under the direction of George S. Rice, the chief mining engineer; the division of petroleum and natural gas, under the direction of J. 0. Lewis, the chief petroleum technologist; and the division of experiment stations, under the direction of D. A. Lyon.

Jan 9, 1919

By Wojciech Naworyta

The development of the Gubin lignite deposit, located in western Poland is the first mining investment of this magnitude in 30 years. Gubin is the second largest prospective lignite deposit in Poland, with over one billion tonnes of indicated reserves, which would be sufficient for a 2700 MW power plant for almost 50 years. The paper presents select problems related to the mining development of Gubin deposit. Attention has been paid to changes in legal and formal requirements for mining investments that were introduced after the change of Polish social and economic system. The significance of spatial, environmental and social conditionings has been emphasized. Typical attributes of the mine planning process have also been presented. Those include the long time horizon of the investment, uncertainty of external conditions and resulting difficulties in the project?s economic evaluation. Focus has been placed on mutual connections between particular elements of the project and time dependence during the process of their development. Iterative characteristics of the design process have been proven, together with resulting necessity of frequent verification of previous assumptions. As a background for presenting selected problems related to future development of Gubin lignite deposit, the methods of design have been discussed ? the variants method, the empirical method and the method of consecutive approximations. The tools and the possibilities of their use for solving specific problems related to mine design of an open pit have been broadly discussed. The chapter in which the authors relate to the specific problems of Gubin deposit development constitutes the main part of the paper. It depicts the assumptions on which the annual production and the total extraction of lignite during life-of-mine period have been based. The process of mine designing has been discussed, taking into consideration environmental, geotechnical, spatial, social and mining conditions. The criteria for choosing the location of the opening cut and the external dump have been mentioned. In the summary, the present state of mine design progress has been presented, together with some problems that will need to be solved during the next stages of the deposit?s development.

Aug 1, 2013

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992