Search Documents

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By A. C. Fieldner

In November, 1926, the American Engineering Standards Committee (now the American Standards Association) called a meeting of representatives of various professional societies and industrial, educational and governmental organizations to consider what action, if any, should be taken on the classification of North American coals. This meeting was called because a system for the use classification of coal, proposed by George H. Ashley, had been referred to the committee by the Coal Mining Institute of America. This meeting, at Pittsburgh, was well attended and was definitely in favor of taking up the whole question of scientific and use classification of coals, including all the various ranks from lignite to anthracite. The American Society for Testing Materials was recommended as the sponsor organization to take charge of the work and organize the sectional committee according to the rules of the American Standards Association. The American Society for Testing Materials proceeded with the organization of the sectional committee, holding a meeting in Philadelphia, June 10, 1927. Officers were elected, regulations adopted, and general plans for carrying out the work were outlined. The total membership of 28 comprising the sectional committee consists of 8 producers, 2 distributors, 9 consumers and 9 members representing general and scientific interest. From this committee three technical committees of 10 to 12 members each were organized: Scientific Classification, H. J. Rose, chairman; Use Classification, W. H. Fulweiler, chairman; Marketing Practice, F. R. Wadleigh, chairman. The Technical Committee on Scientific Classification was requested to formulate a system of coal classification based on chemical and physical properties of coal and with reference to origin and constitution. The Technical Committee on Use Classification was charged with developing a system of classification, if possible, based primarily on the uses of coal and commercial practice; this system to be correlated with the scientific system as far as possible and desirable. The Technical Commitlee on Marketing Practice was formed to collect and collate information on commercial practice for the benefit of the other two committees. The first meetings of the technical committees were held on Nov. 17, 1927, and the first informal progress reports were submitted to the

Jan 1, 1930

By R. B. Ngenda

The ?Kolwezi Zinc Plant?, in French ?Usines à Zinc de Kolwezi? (UZK), has produced about 910 000 dry metric tons of residues during the hydrometallurgical treatment of calcines from sulphide zinc concentrates. The zinc hydro plant residues contain on average 19.47% Zn, 2.7% Cu, 2.1% Pb, 26.6% Fe, 0.12% Cd, 0.39% As, 157ppm Ag, 447.8 ppm Ga, 475.4 ppm Ge, etc. This material was dumped in five ponds in the vicinity of the plant. The high Fe content in the ore concentrates induced important conversion of some of zinc and copper into ferrites during the roasting process. Those ferrites are very stable compounds, which are difficult to leach with dilute sulphuric acid solution. Therefore, they mainly report to the leaching residues. Hot leaching has been successfully applied to the treatment of zinc hydro plant residues. The method, however, presents the disadvantage of simultaneously dissolving iron(Fe). It is then necessary to remove an important iron quantity from solution prior to zinc and other metals recovery.

Jan 1, 2009

By Michael Mann, Kenneth K. Eltschlager

The International Society of Explosives Engineers (ISEE) Standards Committee has recently updated both the Field Practice Guidelines for Blasting Seismographs and the Performance Specifications for Blasting Seismographs. The revisions are the result of public and industry input along with recommendations of the ISEE Blast Vibration and Seismograph Section. The committee is comprised of blasting seismograph manufacturers, users and general interest personnel. On an as needed basis, subject matter experts are enlisted to advise the committee. Three phases of activities are necessary for each revision cycle: request for comment on the existing standard, first draft revision of the standard based on public input, and final draft approval by the ISEE Board of Directors. The ISEE standards revision process will be explained and each standard will be discussed along with the significant revisions from the latest revision cycle.

Jan 1, 2018

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By O. G. Pauw

The relationships between mill power and pebble load, bulk density of the load, and circulating load were investigated on the pebble mills in the grinding circuit at Buffelsfontein Gold Mine. This paper describes the most significant relationships among the operating and control variables on the plant, and illustrates these by reference to experimental data gathered from the plant during operation. The results were used for the development of very successful multivariable peak-seeking controllers for the pebble load and bulk density of the load on these pebble mills. The peak-seeking control algorithms are described in detail. The control system has operated successfully at Buffelsfontein for more than 18 months and is still in operation.

Jan 1, 1985

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By A. H. Bell

The results of repressuring (or gas-drive) have been very encouraging to the several companies doing experimental work along these lines in California. The most notable examples are the Shell and the Union Oil companies at Dominguez, the Marland Oil Co. at Seal Beach, and the California Petroleum Corpn. at South Mountain. The results of the Marland test at Seal Beach are interesting in that re pressuring was started while several wells were still flowing; also, on account of the high pressures required to overcome the hydrostatic pressure exerted by high-head edge water. The well first chosen for repressuring is about halfway up the flank of the structure and had been on the beam making about 250 bbl. of fluid daily, cutting about 60 per cent. emulsion. The fluid lcvel was 230 ft. from the surface and the top of the sand was 4393 ft. Tubing was run to 4000 ft. with a packer and the space above the packer was filled with water to balance the high pressures. Gas was started in slowly to allow the fluid to be pushed back into the sand, and required three days at a pressure of 1500 Ib. per sq. in. before starting into formation. The pressure was once built up to 1800 Ib. and the compressor was shut down for a few hours. When again started, the well took gas at 1500 Ib., and after about three weeks the pressure was dropped to 1450 Ib. The present pressures required range between 1400 and 1450 lb. Volumes as high as 1,500,000 cu. ft. per 24 hr. were put into the well. Increases as high as 50 per cent. in production were obtained in wells up-structure with very little increase in wells down-structure. Also, the water cut on one edge well materially decreased. After about 40 days the repressuring was moved to two wells farther down-structure and the well originally repressured was put on production. The result of this was a great increase in the production of wells one location farther down-structure, a rapid increase in one well one location up-structure, and a decrease in production of the wells farthest up-structure. Later the gas started to short-cut to the nearest well down-structure, nullifying to a certain extent the effects of the repressuring work. The increased production that could be definitely attributed to the repressuring work

Jan 1, 1928

By L. A. Cisternas, R. I. Jeldres, D. Calisaya

"Flotation of copper-molybdenum sulphide ores in seawater entails critical challenges such as selective recovery of molybdenite, effective pyrite depression, and reducing the lime addition required to reach highly alkaline conditions. It is essential that laboratory flotation tests aimed at solving these problems give reliable, reproducible results and indicate the correct approach for industrial operations. Rougher flotation of coppermolybdenum sulphide ores in seawater was investigated using two different cells: a modified Denver cell and a standard commercial cell. The effect of an organic reagent on the flotation performance was tested, and the fast/slow-floating model was used to describe the results. The modified Denver cell significantly improved the reproducibility of the flotation test results, due to technological enhancements such as the impeller being driven from below without a stator, which enables the whole froth surface to be scraped with a paddle at a constant depth and rate. Organic reagents are a promising alternative to inorganic reagents for depressing pyrite in seawater. However, further studies should be conducted to investigate their impact on molybdenite recovery, as well as to evaluate the possibility of depressing pyrite after molybdenite separation. The fast/slow-floating model was found to be appropriate for describing the flotation kinetics of the copper-molybdenum ores. The parameters are useful for comparing the performance at different conditions. IntroductionOwing to the increasing scarcity of fresh water, the use of seawater mining and mineral processing is becoming increasingly important (Cisternas and Moreno, 2014). Seawater can be desalinated by reverse osmosis, but this involves considerable costs, limiting it to the big mining companies (Akgul et al., 2008; Leidner et al., 2012; Ghaffour, Missimer, and Amy, 2013). Furthermore, desalination has environmental consequences (Lee, Arnot, and Mattia, 2011); for example, a desalination plant designed to process 2.5 m3/s requires an electrical energy supply of around 30 MJ/s. To supply this power demand, a thermoelectric plant burning bituminous/sub-bituminous coal mixtures at a thermal power generation efficiency of 35% might release around 1200– 1500 t of CO2 per day. Furthermore, the effluents from desalination plants are typically discharged into the sea, and their high temperature and ionic content inevitably modifies the marine environment, with unknown consequences. The direct use of seawater is, therefore, more attractive, but it also poses major challenges since seawater contains ions that adversely affect mineral recoveries. In particular, in the flotation of sulphide ores in seawater, the floatability of molybdenite is depressed (Castro, 2012; Laskowski, Castro, and Ramos, 2014)."

Jan 1, 2017

By K Hobbs

Mining is experiencing a difficult period of low profitability and declining productivity. To achieve sustainability, mining companies are challenged with improving output, quality and safety while decreasing costs. At the same time, organisations are having to manage a workforce in which individuals no longer accept a traditional style of management, employees prefer more flexible employment, and diversity within teams is becoming the expected norm.Increasing organisational diversity has been shown to have a positive impact on performance and therefore sustainability. Gender diversity and equality between working men and women is the area most studied in this regard. Executives are becoming more aware of the correlation between gender diversity and performance with some larger organisations having dedicated resources to increase the number and status of women in their organisations. Despite this, limited improvement in gender equality is apparent globally over the last decade with some industries, including mining, going backwards. So why is this the case and what other strategies are available?In 2015, the United Nations Women National Committee Australia (UN Women NCA) in conjunction with Autopia released a white paper discussing the lack of visible change in gender equality despite the widespread implementation of merit-based personnel management strategies. Using research from around the world and thoughts from influential government, education and business leaders, the paper ‘Rethinking Merit’ debunks the myth of the meritocracy. It provides a number of recommendations for organisations committed to improving their performance and sustainability through diversity, including a variety of real-life company examples, instead of relying solely on merit-based decision-making.This paper takes the recommendations of ‘Rethinking Merit’ and applies them to the mining industry. It shows the relevance that rethinking merit has for the industry and why applying the recommendations can result in an increase in diversity, therefore enabling greater performance and sustainability of mining companies. This paper provides case studies from Aurizon, Iluka Resources and BHP Billiton and, as a guide for managers, a generic diversity strategy designed to be implemented alongside traditional merit-based personnel management techniques.CITATION:Hobbs, K, 2016. Rethinking merit for a sustainable mining industry, in Proceedings International Mine Management Conference, pp 139-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Boyd GL

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal rCCOvCrCd h\ hi'eh ss-all mining methods.

Jan 1, 1998

By L. H. Thorleifson

Demand for both gem and industrial diamonds is very strong. Synthetic production supplies industrial uses, but synthetic gems remain inferior and expensive, so the large gem market is supplied by mining. Several major mines have been depleted, and the market is receptive to new sources of high quality gems. Canada's Precambrian terrane, extending across the Canadian Shield and under the Phanerozoic cover of the Plains and Hudson Bay, has excellent potential for diamonds, but exploration conditions are difficult due to recent glaciation. Early world exploration relying on recognition of diamond in alluvial sediments was adequate to launch pre-1900 production from India, Brazil, and Africa. Exploration success in Canada, as was the case in Russia and other more recently discovered sources, however, had to await large investments in effort supported by advanced science and technology. Canadian exploration in many ways is similar to that in other regions, relying on analysis of tectonics, indicator minerals, geophysical surveys, and multiple stages of drilling and sampling. Very different from other regions, however, is Canada's surficial environment, in which recent glaciation has caused fresh indicator minerals to be transported hundreds of km. Exploration accelerated in Canada after 1960, first in Ontario and the Arctic Islands, then in Saskatchewan in 1988, and most importantly after the Chuck Fipke - Stew Blusson discovery at Lac de Gras, Northwest Territories, in 1991 that led to the billion-dollar BHP - Dia Met Ekati Mine that opened in 1998. In 2003, production from Ekati is expected to be supplemented by that from the similar and nearby Diavik Mine of Rio Tinto and Aber, currently under construction. These mines will bring Canadian output to over 10% of world supply, and will position Canada with Botswana and Russia as world leaders in production of high quality gem diamonds. There could be other mines as well, as sites across the Arctic and in the south from Alberta to Québec are being explored by an array of companies, including De Beers, other majors, and several juniors.

May 1, 2001

The American Petroleum Institute, 250 Park Ave., New York, N. Y. Lacey Walker, Secretary. A complete price list of publications will be sent upon application. The American Petroleum Institute issues a variety of publications; in addition to the Daily Oil Digest ($25 per year) and a weekly Statistical Bulletin ($12.50 per year to nonmembers), a Quarterly is published ($4 per year to nonmembers). Books published by the Institute: American petroleum supply and demand, $3; A series of "Petroleum facts and figures" for each of the years 1928, 1929, 1930 and 1931, $2 for each copy; Function of natural gas in the production of oil, $1; Bibliography of organic sulphur compounds, $4; and "Oil" (Oil Industry Series in one volume), 50 cents per copy. Volumes of the first six annual Meeting Proceedings are out of print, but the Proceedings for the 7th annual meeting in 1926

Jan 1, 1933

By John Oxenford

There are currently two operators producing oil from the surface-mineable portions of Alberta?s oil sands (Syncrude Canada Ltd. and Suncor Inc.) and two other companies are proposing to enter the industry (Albian Sands in 2002 and True North in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of recoverable TiO2 and approximately 80 000 tonnes per year of recoverable zircon. This represents approximately 6% of the world?s TiO 2 consumption and approximately 9% of the world?s zircon production. With the commissioning of plants by Albian Sands and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in Alberta?s oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widelyheld suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers: 1) The bitumen coating on the sand grains; 2) Secondary mineralization such as pyrite, siderite and calcite 3) A high proportion of aluminosilicates (approximately 25%) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier. The pyrite can be removed by flotation. And the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

May 1, 2001

By Bojcevski D

The deportment and textural relationships of silver bearing phases are key characteristics in understanding the behaviour of silver ores in flotation tests or processing plants. These characteristics are however difficult to define and quantif

Jan 1, 1997

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985