Search Documents

By N. Sauret-Szczepanski, G. Patry, S. Gauthier, G. Potvin, C. Munger

Adsorption/thermal desorption with sorbent cartridges and analytical method using gas chromatography coupled to mass spectrometry (GC/MS) was developed for the determination of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) emitted from primary aluminum smelters. A customized cartridge was built like a packed column with a stainless steel tube filled with a specific resin. The optimization of adsorption and desorption parameters was carried out to support the PFC sampling for all aluminum production technologies. The proposed method showed good linearity for concentrations ranging from 10 to 500 ppbv for CF4 and from 5 to 500 ppbv for C2F6 with correlation coefficients above 0.999. In certain conditions, the detection limits of the analytical method reached 0.3 ppbv for CF4 and 0.15 ppbv for C2F6- Using this methodology, a field campaign was carried out using a sequential sampler allowing the simultaneous sampling of PFC with cartridges and sampling bags. The results showed no significant difference (t-test) between the two sampling technologies and no breakthrough was observed from the cartridges .

Jan 1, 2006

Jan 1, 1942

By Groom P.

The wastage of timber in coal-mines that is caused by decay is very great; in fact, far greater in this country than is generally realized. Mr. E. W. Peters estimates that of the whole wastage of timber in mines in the United States of America, 50 per cent, is due to decay and insects; of this 50 per cent, an overwhelming part is due to decay. The most efficient methods of decreasing this grave loss can be devised only by co-operation of the mining engineer and the scientific expert, and it is partly in the hope of procuring such collaboration that this paper is written. It contains, therefore, a resume of our present knowledge of the decay of wood, and of the economic methods of checking this in mines; but, with a view to improving those methods, it also directs attention to the gaps in our knowledge and the means by which these can be filled by future investigation

Dec 1, 1916

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By Jerry E. Olson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 20,071-acre South Fork Wilderness Study Area (OR-005-033) and part of the 8,791-acre Sand Hollow Wilderness Study Area (OR-005-034) in order to evaluate their identified mineral resources. The study areas are located in Crook County, OR, about 58 air miles east from Bend. The areas studied are underlain by Tertiary- and Quaternary-age volcanic and tuffaceous sedimentary rocks. No mineral resources were identified in or adjacent to the study area. Except for common opal and agate occurrences along the northern boundary of the study areas, no mines, prospects, or mineralized zones occur within the study areas. Bentonite is periodically mined less than 1 mi southwest of the Sand Hollow study area boundary. Neither of the study areas has geothermal leases, but both areas are under lease for oil and gas.

Jan 1, 1987

By H. S. Chiang, D. F. Lu, S. S. Peng

INTRODUCTION The most important element in a successful lingual mining is a good roof control. The modern longwall mining employs hydraulic powered supports for roof control at the face area. The application of hydrau¬lic powered support requires the knowledge of over¬burden strata behavior for proper selection of sup¬port type and capacity. Failure to do so could lead so serious loss. There are several methods available for determining the required support capacity (1-3). While these methods are simple for application, they do not include the complicated roof behavior observed in longwall mining. As research progresses and operational experience accumulates (4,5), the concept about the designing and selection of powered support improves. The design of a longwall powered support consists of three major phases: 1. structural integrity and stability of the powered support, 2. external loadings induced by the movements of the overburden strata, and 3. interaction between the support, roof and floor. Phase 1 involves structural analysis (5) and full-sized testing (6) of the supports. Its validity is limited by the accuracy of the assumed external loading because of the uncertainty about the actual loading underground. The third phase includes the reaction of the support and the floor to the movements of the overburden strata and vice versa. Among the three phases, the second phase concer¬ning the external loading seems to be the least known because of the complicated behavior of the roof strata. There are many unresolved problems. For example, does the main roof break periodically and cause periodic roof weighting in the face area? If so, are there any rules governing its behavior? How does the roof load on the support canopy! Finally, how can one determine the required support capacity and select a proper type of support to meet a certain roof behavior? In order to answer those questions, underground instrumentation and observations were performed at 4 longwall panels in 3 separate mines for the past two years. This paper summarizes the current findings. PANEL LAYOUTS AND EQUIPMENT EMPLOYED The three mines selected are all located in West Virginia; two in northern and one in southern West Virginia. As shown in Table 1, seam conditions (i.e. seam, depth and thickness) and panel layouts are different among the three mines. The most significant difference in equipment is the face powered supports. Three mines used three different types of shield; 2-leg caliper, 2-leg lemniscate, and 4-leg lemniscate chock-shield. (Fig. 1) UNDERGROUND INSTRUMENTATION AND OBSERVATION PROGRAM Two events were instrumented in each observed longwall face: one was the hydraulic pressure (resistance) of the powered supports and the other was the canopy load distributions. In addition, the gob caving conditions were visually observed and recorded. Leg and Support Resistances One or two automatic Weksler Pressure Recorders were installed at the designated shield support,. In most cases, the daily charts were used to record the pressure variations in both the front or the rear legs (for the 4-leg shield), or in both the leg and the fore-pole ram (for the 2-leg shield). The recorded pressure w a s then converted to load or resistance by multiplying it by the cross-sectional area of the hydraulic leg or canopy ram piston. Fig. 2 shows the typical pressure-recorded charts for the 4-leg and 2-leg shields in a 23-24 hour period. The support resistance is the summation of the resistance in each of all the legs for that support. Generally, the resistance of the fore-pole ram will not be considered in determining the capacity of the support because of its rather small vertical compo¬nent force at the tip of the fore-pole. Canopy Load Distribution External load distribution on the canopy as exer¬ted by the roof was monitored. The measurements employed 12-14 pieces of pressure cells (6-inch square) that were uniformly arranged in two rows on the canopy. After support setting, the pressure changes in the cells were monitored at various stages of the mining (supporting) cycle while the support leg pressures were recorded continuously by the pressure recorders. Based on the calibration chara¬cteristics of each pressure cell as performed in the laboratory before and after each underground test, the cell pressures were converted to actual loadings. From these load measurements the canopy load distri¬butions and the relations between measured canopy loadings and support leg resistances were determined. Accordingly, the supporting efficiency of the shield support can be determined.

Jan 1, 1982

By Joseph W. Ruetz

The paper describes the San Nicolas deposit, México. San Nicolás deposit is the most important VMS deposit discovered in Mexico to date, and a major deposit on a global scale. The discovery of San Nicolas resulted from the early recognition of VMS mineralization in a region not known for this style of mineralization, and the flexible use of appropriate exploration technology.

Apr 24, 2001

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

By I. L. Grigorova

As a result of the main processes of the limestone treatment ? sawing, buffing and polishing, a technological waste is usually obtained. These final tailings consist of a water suspension with highly variable solid phase content and granulometric composition. Since the waste is conducted to a tailing pool or another place, this leads to environment pollution. In this work the slurry waste generated during the limestone processing in a Bulgarian limestone manufacturing company was characterized. The chemical composition, particle size distribution, solid phase content, whiteness, yellowness, abrasion, specific surface and density were determined. The possibility of obtaining building/construction materials from limestone processing waste was studied in a laboratory scale. The technological tests included thickening, filtration and drying of waste products. Continuous operation laboratory thickener was used. Coagulant Accepta® 8302 (aluminum sulphate solution) and anionic flocculant Magnafloc® 155 were found to be the most effective in the sedimentation of the products. Filtration tests were performed using a laboratory pressure filter. Drying tests were carried out in laboratory facilities using the direct heating method. On the basis of the laboratory results a technology for limestone treatment waste was developed. A production line for building materials from limestone slurry was set up. As a result the manufacturing company has a possibility to use circulating water.

Jan 1, 2014

By Mowry Bates

The following example of the practical application of engineering geology is of interest in that it demonstrates the advantage of keeping accurate records of all wells, whether drilled by onn's self or by others, together with the advantage gained by gathering such data during the process of development. The fault described was found in the autumn of 1915, during the hurried development caused by the discovery of the famous Gusher Bend pool in Red River Parish, Louisiana. The writer was at the time employed by one of the operating companies as geologist, and the example is a portion of the routine work. Location The oil fields of northern Louisiana and east Texas are located in Caddo, Bossier, De Soto and Red River Parishes, Louisiana, and Marion County, Texas. A very narrow strip of the eastern portion of the latter is productive. The producing oil pools are known as the Caddo Field, in the northern part, and the De Soto-Red River Field, in the southern. The two fields are 60 miles apart. There are several gas fields between them, but no important supply of oil has been found, though there are several producing wells in the Anona chalk, locally called the Chalk Rock, in the Elm Grove gas field in Township 16 North, Range 11 West (see Plate 1). General Geologic and Structural Features The general geology of northern Louisiana has been excellently described by A. C Veatch in Professional Paper No. 46, U. S. Geological Survey; by G. D. Harris, Bulletin No. 429, U. 8. Geological Survey; and later by George C. Matson and Oliver B. Hopkins in Bulletins No. 619 and 661C, U. S. Geological Survey.

Jan 1, 1920

By H. Wilton Clark

"IntroductionTHE CANADIAN use of short-period delay-action detonators in coal shooting has been carried on for about two years, mostly in British Columbia, and this is a preliminary report on progress to date. Entire coal faces are being shot successfully with one application of electric current.The electric blasting cap came into use about the beginning of the century. The low-tension electric cap, the type most commonly used, consists essentially of a metal tube containing an initiating explosive. Two wires lead into the end of the cap and are connected inside the cap with a short 'bridge wire .of very high resistance. This •bridge wire is buried in a match-head of a readily ignitable powder composition. When current goes through the lead wires, the bridge wire becomes extremely hot and sets• off the match-head which, in turn, ignites the powder just below it in the tube. This explosion sets off the main charge of explosive. Thus, by connecting a group of caps to a source of electric .current, a number of charges could be exploded simultaneously. This immediately became of great value to mine and quarry operators. Explosives could now be used to break up large masses of material at one time, as against the older, slow method .of blasting small amounts with single charges.The next step was to develop a delay detonator which would allow charges of explosive to fire one after the other, one or two seconds apart. Such detonators allowed first blasts to relieve some rock burden before the next charge fired, giving the second charge an easier task in forcing out more rock, and so on for the rest of the series of charges."

Jan 1, 1953

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By P. K. Kaiser

A rational approach for the design of fully grouted bolts in underground excavations is presented. An analytical model involving elasto-plastic concepts and the mechanics of bolt/ground interaction was developed and tested by comparison with laboratory tests and field measurements. The theory elucidates the influence of shear stress distribution, bolt pattern and geometry on tunnel convergence. Laboratory simulation has provided convincing evidence to support the theoretical predictions. A dimensionless bolt efficiency parameter is introduced as a design tool that relates the reduction of tunnel convergence to the bolt length and density. Its application in practice is highlighted by the analysis of one case history.

Jan 1, 1987

By Harold A. Krueger

FACILITIES and mining operations of the National Lead Co., St. Louis Smelting and Refining Division, near Fredericktown, Mo., are situated in a famous mining area. Copper, lead, nickel, and cobalt have been mined here for more than 100 years, work having been started on a high sulphide copper outcrop in 1847.

Jan 8, 1953

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By J. D. Irving

In the summer of 1899 there appeared in the Black Hills Mining Review† a short note announcing the discovery of certain deposits of wolframite in the vicinity of Lead City and Yellow creek, Lawrence co., South Dakota.

Jan 1, 1902

By M. C. Manderson

While the United States has been the world's largest volume producer and marketer of phosphatic fertilizers for many years, it has recently suffered heavy losses for a variety of reasons. While improved economic performance is expected, it is still at least a year or two away. But when recovery does manifest itself, it will likely yield only mediocre profits, due in part to the fact that about 50 percent of output is export-dependent. Therefore, there appears to be limited likelihood that profits will be adequate to justify the further outlay of large amounts of capital for expansion.

Jan 1, 1986

By Mark S. Stagg, Steven V. Crum, Stephen A. Rholl

As part of its ongoing research concerning rock fragmentation by blasting, the Bureau of Mines has undertaken a series of test blasts where six cylinder-shaped pieces of granite rock were fragmented using high explosives. The tests were intended to: 1) Establish a dataset that could be used in the development and verification of theoretical models that simulate rock blasting and 2) To add to the fragmentation data currently being collected by Bureau researchers. The cylindrical geometry was chosen so that the fragmentation could be directly compared to two-dimensional computer simulations that assume an axisymmetric configuration as well as more sophisticated three-dimensional models. The granite cylinders, Carnelian granite and Charcoal granite, ranged in size from about 0.46 meters (18 inches) to 0.58 meters (23 inches) in diameter by 0.91 meters (36 inches) to 1.52 meters (60 inches) in length. Physical rock properties tests performed on the Charcoal granite cylinders indicated that the rocks did in fact have similar physical characteristics. PETN-based detonating cord and dynamite were used as the explosive charges and estimates of the values of some important physical properties are given. For the first five tests, the blasted rock was contained by a heavy rope mat suspended inside the Twin Cities Research Center's blasting shelter. The fragments from each of these shots were sorted and weighed to determine the corresponding fragment-size distributions. Even though different types of granite and cylinder sizes were used, similar fragment distributions were produced from shots that used a similar explosive, in this case the PETN-based detonating cord, and comparable burden-to-charge diameter ratios. Significantly coarser fragmentation was produced from a blast that used dynamite as the explosive charge. Fragment velocities were calculated using photographic data from the sixth test which was shot unrestrained in a quarry and filmed with high-speed cameras.

Jan 1, 1990