Search Documents

By E. L. Singleton

The electrochemical reduction of aluminum chloride to aluminum was investigated in a closed, two-compartment cell utilizing a molten chloride electrolyte. The externally heated cell was divided into a reduction compartment and a combination AICl3 feed and metal removal compartment. Aluminum was deposited at 700° C on a molten aluminum catbode from a KCI-NaCI-AICI3 electrolyte. The AICl3 content of the electrolyte was replenished by either vapor or solid additions. The chlorine evolved was collected and measured to give a quantitative evaluation of AICl3 reduction. The effects of anode and cathode current densities and AIC13 concentration on anode current efficiencies were studiedo A range of 64 to 84 percent anode current efficiency was obtained with the 25-pound electrolyte capacity cell and related auxiliary equipment.

Jan 1, 1968

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By M. P. Meehan

The purpose of this paper is to present the key elements in a system; study of the electrical system for a timing and/or tilling operation. The ability of an electrical system to function in a reliable fashion at its proper levels is essential for an operation to be successful. A system study consists of a load study for determining the capability of the electrical network to provide power to the various loads and a short circuit study for determining the capability of the electrical protective equipment to properly protect against fault conditions. The sequence of events in a system study is data acquisition, determining the electrical parameters and analyzing the ability of the system to meet these requirements. If the system is small, herd calculations will be the manner in which the study will be conducted; if it is large then commuters will be used. A load study has as its objectives the determination of the capability and reliability of the source of power, transformers and conductors to satisfactorily deliver power to the loads at an acceptable voltage level. The Information required is a single line diagram showing the source, transformers, conductors and loads.

Jan 1, 1980

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By J. M. Stuve

Calorimetric data for the dissolution of scandium sesquioxide and scandium trichloride in 4.360 molal hydrochloric acid were used to evaluate the standard heat of formation of ScCl3(c). The heat of reaction for Sc(c) + 1.5Cl2(g) = ScCl3(c) at 298.15° K was computed as -225,440 ±340 cal/mole.

Jan 1, 1965

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

The following list of US companies, mines, and mills engaged in uranium production was compiled by the Health and Safety Analysis Center, Mine Safety and Health Administration, in Denver, Colo. The list includes those companies reporting to the Center in 1978. Thanks to D. K. Walker, Chief of the Health and Safety Analysis Center, for providing the information to MINING ENGINEERING.

Jan 10, 1978

By T G. Callcott

Australian coking coals are either class 434<tlj534<2l, at Port Kembla, or 634<3> at Newcastle. The former yield good blast-furnace cokes; the latter yield poor ones. However, increases in conventional strength indices, by methods applicable with normal coking ovens, seem unlikely to be economically attractive. Characterization of the coals has enabled an "economic" blend to be developed in the Newcastle area, and this has affected mining, preparation and handling operations. Coking studies have led to a specification for the making of strong coke, especially from the high-volatile Newcastle coals. Continuous coking studies, developed from the efforts to make very strong coke, have taken two directions. Firstly, coking thin layers of coal on strands; secondly, coking, in various types of vessels, compacts of coals with or with-out the inclusion of non-coking coals, iron ores or other inert materials. Gas, "sand" and hot metal coking have been tested for use in compact coking. Particular attention has been paid to pellets of coal and ore. The probable industrial problems in adopting any of the ideas are presently being examined.

Jan 1, 1963

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB&apos;s daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By D. J. Burkhardt

Newer copper SX/EW facilities often incorporate hot water heating for the cell feed electrolyte to obtain the necessary plating temperatures of 40 to 50°C. Heating is most necessary in oxide heap leaching, however it may also be required in bioleaching of secondary sulphides in colder climates or higher altitudes where most of the heat gain in the heap is lost to the environment. Given that the solution flows in the leach, organic circuit and electrolyte circuit are circular in nature, and the fact that the hot lean electrolyte is often exchanged with cooler rich electrolyte, it can be difficult to access the heating requirement for the cell feed. There are energy losses in piping, tankage, raffinate, and energy gains through the PLS and electrowinning process itself; some of these are significant and others are not. This paper discusses the overall heat balance, the relative significance of the various energy gains and losses, and describes a methodology to develop a heat balance to assist the engineer in sizing the heating equipment.

Jan 1, 2003

By Peter Lighthall

What is an engineering firm?s role? ? The ideal situation is a life of mine service alliance with the owner ? Engineering firms are long term custodians of information ? Maintain consistency with established closure objectives, adjust closure plans to meet changing situations and technologies ? Develop range of solutions and present owners with risk profile The mine closure planning process ?new mines ? For metal mining, geochemistry is the issue ? The planning process: ?Sampling ?Waste characterization ?ARD prediction ?ARD control strategies ?Life of mine waste management planning ?Assessment of residual impacts ?Development of strategies for dealing with residual impacts ?Estimate closure costs ?One time decommissioning and reclamation costs ?Ongoing treatment/maintenance costs

May 1, 2006

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012

Objective To develop safety training tools for mine safety and health professionals that fill gaps in currently available materials. Background Over the past 4 years, NIOSH has developed and released a series of training videos targeted at underground mine safety. These videos were developed in close cooperation with the mining industry and safety training professionals and were intended to provide realistic, interesting, effective training to both new hires and experienced miners. The videos cover the mining cycle, starting with the breaking of the rock (Handling Explosives in Modern Mines), making certain the work area is safe after a blast (Rock Falls— Preventing Rock Fall Injuries in Underground Mines), installation of ground supports and recognition of failed supports (Miner Mike Saves the Day), and hauling both ore and materials in the mine (Hazards in Motion). A separate video (Hidden Scars) captures the story of a fatal rock burst through an interview with a miner who nearly died and who lost his partner in the accident. These videos have been extremely popular in the mining industry and are being used across the nation as well as in 18 other countries. Two of them, Rock Falls and Miner Mike Saves the Day, have won Alice Hamilton awards, NIOSH’s highest recognition for Excellence in Occupational Safety and Health, in the Educational Materials category. Approach A recently completed independent evaluation of the SRL mining videos identified five themes that mine safety trainers consider necessary for successful training materials: high quality, credibility, accurate content, effectiveness, and an engaging nature. All of the NIOSH videos were rated very high for each theme. Using these measures of effectiveness, a more difficult challenge has been undertaken. Much has been written in the mining industry about the coming turnover in employment. The average age of miners in the United States is approaching 50, and many of the “experts” will be leaving the industry as they reach retirement age. The mining industry, like many industries involving skilled labor, relies heavily on a master-apprentice relationship between new hires and older miners. New hands learn from experienced miners. Their learning falls into three primary categories—they learn what’s important to know, they learn how to do things correctly and safely, and they learn the culture.

Mar 1, 2002

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

By Motyka J, Adamczyk AF, Witczak S

A case study of migration of a paper factory fluid wastes, on the distance of 5 km from an underground disposal site to an ore mine is presented. The ore mine in question, situated in SW Poland is pumping 3.5 m3/s (ca 300 000 m3/day) of groundwater, producing a cone of depression about 150 m deep and several kilometers wide. The migration of wastes (pollutant) occurs within the carbonate karstic aquifer of Triassic age. The aquifer is about 100m thick and is characterized by the coefficient of hydraulic conductivity equal to 8 m/day on the average. The results of systematic measurements carried out for 13 years enabled to estimate the mean breakthrough curve of the pollutant. On this basis and taking into account the coefficient of hydraulic conductivity as well as the mean hydraulic gradient between the disposal site and the ore mine, the migration parameters of the polluting material, i.e. the real flow velocity, the effective porosity and the longitudinal disper- sivity have been calculated. As the measurements considered a long migration distance of the pollutant, the obtained hydrodynamic dispersion constant (dispersivity), in the authors opinion, is reliable enough to be applied for regional groundwater calculations, regardless of the "scale effect".

Jan 1, 1988

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau&apos;s Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By A. J. Basu

An overview of the evolution of computerized mine planning and design has been given, emphasizing the need for a knowledge-based system for planning and design of underground coal mines. An outline for the development methodology and procedure has been provided. Problem structuring guidelines have been used to incorporate intelligence and integration to the design modules. A skeletal model for a mine planning and design expert system has been prescribed, and the development process has been documented in detail. A feasibility prototype has been developed to test the structure of the skeletal model and to ensure completeness of the design process. The feasibility prototype development and its contribution toward proto typing has been addressed in this paper. At present, prototype development is underway. The prototype is expected to be avail-able for testing and implementation in early 1991.

Jan 1, 1991

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985