Search Documents

By Zeng Zheng, Liu Chen, Yu Xing-Fu, Tian Su-Gui, Zhang Chao

"Single crystal nickel-base superalloy is prepared by using the various withdrawing rates. By measuring creep properties and microstructure observation, the influence of the element segregation on creep properties of the superalloys is investigated. Results show that the dendrite spacing and the segregation extent of the elements decrease with the enhancing withdrawing rate. The superalloy with smaller dendrite spacing has lower segregation of the elements and better creep resistance. The dislocations climbing over the rafted y’ phase is thought to be the deformation mechanism of the alloy during steady state creep. In the later stage of creep, the fact that some dislocations shear into the rafted y’ phase may twist the rafted y’ phase. As the creep goes on, the initiation and propagation of the cracks occur up to occurring creep fracture, which is thought to be the fracture mechanism of the superalloy during creep.1. IntroductionSingle crystal nickel-based superalloys consist of high volume fraction of ?? strengthening phase and ? matrix, and possess the excellent high-temperature mechanical and creep properties, therefore, they have become the main material to make the blades of the advanced aeroengines[1-3]. Some literatures report that the temperature-bearing and creep-resistance properties of the single crystal nickel-based superalloys can be remarkably improved as the increases content of the refractory elements, such as W and Re[4-6]."

Jan 1, 2012

By Kewal K. Kohli, Stefanie Self

"Three cases of surface subsidence investigated over abandoned coal mines after flooding in one case and dcwatering in two cases are presented in this paper. Mining was conducted by the room and- pillar method at all the mines leaving stable pillars. This paper will discuss the background chain of events and the likely causes of the pillar failure resulting in surface subsidence.CASE NO.1BackgroundThe Pittsburgh scam was mined in 1960 by the room-and- pillar method, leaving pillars (Figure I) through Mine A. located in Monongalia County. West Virginia.The mining height in U1is area was 1.83 m (6 ft) with an average mining depth of 140 m (460 ft). The mining recovery was 62% and the safety factor of the pillars was calculated at 1.15 using the Bieniawski ( 1984) fom1ula. For stable pillar design. a 1.5 safety factor is recommended. A 1.15 safety factor is considered marginal. Pumping continued after the mine was shut down in 1960 to prevent water seeping into an adjoining mine owned by the same company. The pumping ceased on December 12. 2003, and the mine was allowed to flood. The water level rose about 17 m (55 ft) by August 3 1, 2004, based on observations in a nearby borehole. On September 3, 2004 surface subsidence occurred above this area causing damage 10 a residence (Figure 2).Summary of InvestigationThe floor of the Pittsburgh coal scam played a strong role in the pillar failure. In this area, the immediate floor of the Pittsburgh seam consists of about two feet of fireclay. Extensive damage to the surface house was an indication that a major collapse below the surface had occurred. The pillars supporting the overlying strata were evaluated to find the cause of their failure. The pillars in the Pittsburgh seam (sec Figure I) had a marginal safety factor of 1.15 before flooding and were stable for 26 years. Once the mine was flooded the water level in the Pittsburgh seam rose by 17 m (55 ft). Shortly thereafter the fireclay in the floor weakened, resulting in several pillars punching into the floor unevenly making the immediate roof unstable. The overburden strata supported by these pillars also subsided do"" n into the mine, causing damage to several house on the surface."

Jan 1, 2010

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By J. G. Jenkins

Magma Copper Co.'s San Manuel solvent extraction/electrowinning (SX-EW) facility has operated since May 1986. The original facility had a design capacity of 22.6 kt/a (25,000 stpy) of electrowon copper cathode produced by processing pregnant leach solution from an open pit-heap leach operation. In 1988, the plant was expanded to 45.3 kt/ a (50,000 stpy) to incorporate processing in-situ leach solutions. This pager focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research using surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1995

By Joseph Hartshorne

The nature if this process and the general course of its development have already been described by me in two papers read before the Institute.* Since the latter paper mas read, in February, 1898, the development at Kladno has been almost altogether in the direction of using metal direct from the blast-furnace. This has now been the regular practice for about a year. The molten metal is brought from the furnace in ladles, without the intervention of any mixing- or accumulating-reservoir. The plant remains practically the same as originally described by me,† except that the primary furnace has been enlarged as much as was permitted by the existing conditions. This was done primarily in order to increase the capacity of the

Jan 1, 1901

By M. E. Grimes

The Port Radium mine of Eldorado Mining and Refining Limited, located on Great Bear Lake only a few miles from the Arctic Circle in north-western Canada, is the oldest uranium producer in Canada, The first concentrates were produced in 1933 and except for a period between 1940 and 1942 the mill has operated continuously. Although it is located in a remote area, and compared to more recent mines in other areas is a small tonnage operation, nonetheless the relatively high grade of the Port Radium ore has permitted operation to date on an economical basis. The mill process at Port Radium includes the original gravity concentration mill, and since 1952 an acid leaching plant which treats tailings from the gravity mill and tailings recovered by dredging of residues from underwater dumps in Great Bear Lake. The pregnant solution from the leach plant has to date been processed through aluminum reduction to yield an intermediate grade uranous phosphate-arsenate precipitate, Because of the rising costs of the aluminum reduction process, and its sensitivity to ore composition, Eldorado became interested in possible application to Port Radium of the solvent extraction processes of which we were obtaining increasing information in the latter part of 1954 and during 1955.

Jan 1, 1958

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of X-ray backscatter, iron K, fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1993

By Daniel Moroz

This paper will provide an informative overview of the types of explosives and the various methods employed to control avalanches within the boundaries of major ski resorts.

Jan 1, 1991

Jan 1, 1899

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965

By F. C. Stanford

The work of an engineer is to direct natural forces so that the: bring about the results that he wishes to secure. Heretofore he ha concerned himself chiefly with physical forces and inanimate objects until he has secured a truly marvelous degree of control over them The great problem of the present age is to secure a like degree of know1 edge and control of the human factor. Progress has already been made along this line, but it is only a beginning. Wilhelm Ostwald says tha scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to main tain a high average in prophecy. In short, 'the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essentia need of the period is for more brains; if we only had sufficient knowledg and sagacity we could not only solve all difficulties, but prevent then from arising. This generalization holds good for an industrial organization. Th most vital need of the management is for more brains. The logica course for an engineer in charge of an industrial organization is, therefore to direct whatever forces may be at his command toward the development training, and guiding of all the brains in his organization. This is easie said than done, for it involves the carrying on toward two objective: the maximum of productive work, and the development of the individual who perform it. This is essentially like the rebuilding and enlarging of plant, keeping it in full operation the while. On the other hand, if th aim is merely for maximum production from an organization, withou offering opportunity for development, the final outcome will necessari be like that of a plant that is driven at full capacity without stoppin for repairs or improvements; it eventually becomes so run down th either a complete rebuilding is necessary or else it has to be abandone

Jan 1, 1918

By R. C. Gifkins, K. U. Snowden

The value of the index n in power ktivs for the stress sensitivity of minimum creep rale at lead is derived front results drawn from lite literature and from previously unpublished nork on commercial (99.99 pel) and high-purity (99.999 pel) lead polycryslalline and hi crystal specimens. In tests al 0.5Tm (22 to 50'C) for slvesses below 250 psi, n fulls to mily for poly-cr,yslullirle specimens, single crystals, and bicrystals, and toy grain boundary sliding in bicrystals. Between 250 and 500 psi there is a tyansilion range and, for the polycrystalline specimens al least, u high-stress regime for 500 to 1500 psi where n is 5 or 6. These results are such that none of the suggested stress taws can he used to extrapolate to very loir stresses. Meclianisms for deformation in Ike grains and toy grain boundary sliding in the low-strcss regime are outlined. In particular, the mechanism for grain boundary sliding involves sliding controlled by diffusion from tensile to compressire Ledges. predictions based on this model give promising numerical agree-nicul with experiment. II is suggested that the mechanism for grain boundary sliding may he important in other circumstances, e.g., in creep of ceramic materials or superplaslicity, because it can operate with lille or no dislocation aclirity. WhEN the stress dependence of secondary creep rate is represented by a power law the values taken by the stress exponent n are found to vary between 1 and 7, see, c.g., Garofalo.' In Eq. 1 11 u is the applied stress and A a constant. The case for accepting values of v = 1 rests principally upon tests at high temperatures (>0.9Tm) and there have only been isolated tests at lower temperatures (rather than plots of creep rate against stress) for which the creep rates are such that some form of Nabarro-Herring creep with n = 1 is applicable. Hanson5 and Greenwood and cole6 plotted creep rate against stress for tests made in the vicinity of 0.5Tw, and found a "creep yield", so that below a certain low stress the creep rate was linearly related to stress: these observations appear to have been subsequently ignored. Various models have been proposed which agree with a large body of experimental results in which n equals -5 at high stresses (e.g., weertman7 and McLean8). Various alternatives to Eq. [1] have been proposed principally as a means of unifying creep data, but sometimes, it seems, in order to obviate the necessity for assuming a series of regimes of deformation associated with the various values of n; further refer- ence to these will be made in the section on stress laws. This paper calls attention to extensive results which show n = 1 for the creep of lead at room temperature (0.5 T,). RESULTS Fig. 1 is a composite diagram based on figures in the literature6,9,10 with additional results obtained by the present authors and their colleagues11,12 in the course of a number of investigations not directly concerned with stress sensitivity. In Fig. 1 In creep rate is plotted against In stress. The curves show results for two kinds of material. Lead I is of commercial purity (99.99 pct Pb) and lead IT a specially refined material, hydrogen-purified to remove oxygen; it contains 99.999 pct Pb. Curve A is for lead I in polycrystalline form (grain diameter 0.02 to 0.05 cm) at room temperature (22' to 26°C). Curve B1 is for lead I, polycrystalline, tested at 50C. Curve B2 is for lead 11, polycrystalline (grain diameter 0.02 cm), tested at room temperature (22 O- Curves C to F relate to tests made of bicrystals of lead 11: all of the same nominal orientation ("Y" in Ref. 12). Curves C and V are for creep within the component crystals of the bi crystals at 22°C (AB and CD in Fig. 2). Curve E is for creep measured in a gage straddling the boundary, approximately 0.15 mm either side (BC in Fig. 2). Curve F shows rates of grain boundary sliding (as distinct from strain rates in the other curves), obtained by averaging the offsets of six marker lines on the bi-crystal boundaries. The principal feature of the results is that the stress sensitivity falls into two distinct regimes, according to whether the stress is below approximately 250 or above 500 psi (there is a transitional range between 250 and 500 psi). The new result is that below -250 psi two of the curves (A and BI) give a value of n 1, and the other curves also drop below n - 2 to -1.5 but do not extend to low enough stresses to show clear evidence of n 1. At very high stresses the curves tend to give values of n - 6, as previously determined in other investigations. Curve R2 for the high-purity lead in polycrystalline form at room tenlperature almost merges with B, and thus gives new significance to the values for stresses of 150 and 200 psi; previously'3 these points had seemed to fall away from the curve of slope -3, but they now can be seen as almost completing a transition to n = 1. It should be noted that there was originally considerable apparent scatter in the results for the high-purity lead. However, this was found to be associated with annealing conditions or variations in residual content of oxygen and curve B2 was constructed using the highest rate (i .e., the rate for the purest lead) determined for each stress during the course of various investigations over the years: altogether, some forty tests were used in constructing curve R2.

Jan 1, 1968

By Nicholas Enraght – Moony, Alvin Johns, Zhonghan Zhang, Zhang Xianhua, T. Choo

"The tungsten (WO3)-rich ores from King Island Scheelite (KIS) Mine, Australia, containing scheelite(CaWO4) were previously recovered by gravity separation and flotation of fine scheelite (1978-92) with an overall recovery of 76% when both circuits were operating. Recently extensive test work has been conducted both in China and in Australia on KIS ores, assaying from 0.50%-1.34%WO3, and tailings assaying 0.2%WO3(GZRINM 2009; 2011a; 2011b). A new approach, which aimed at improving both recovery and grade of concentrate by means of an innovative all flotation route WOF (Whole Ore Flotation), achieved excellent results: 90%-92% recovery to concentrate grade of 66%-70%WO3for the ores. The process is characterized by the use of selective reagents in flotation, including a newly developed collector for scheelite, GYWA. The WOF process also embraces the "Improved Petrov Method" in the cleaning of scheelite rougher concentrate. Earlier investigations found that the removal of sulfides by flotation prior to scheelite flotation was not necessary. It was also found that recycling of process water did not influenceresults. Two main ore types were tested as well as tailings from 2009to 2001(0.20%WO3). In addition a flow sheet using wet high gradient magnetic separation (WHGMS) in tandem with flotation was also investigated for the tailings."

Jan 1, 2014

By M. S. Seehra, R. S. Pandurangi

"The interaction of amorphous silica particles with several hydrogen bonding agents (H2O,, C2H,OH, C,H,NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy, It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction of surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C,H,NO > C2H2OH > H2O.The use of IR spectroscopy to study the adsorption on solid surfaces is well documented in the literature,"" For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1. Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-6 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity,7-9 catalysis,10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated-have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8N0), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by IR spectroscopy, and Knozinger16 and Rouxlet and Semples17 have used transmission IR spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties, In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18,19 Moreover, according to a recent paper,20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry, In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H5OH, and H20) with the silica surface by monitoring changes in the surface IR modes, Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents, Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16,17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification, Details of this work are given below,The Cab-O-Sil samples of silica used here were obtained from the Cabot Corporation of Tuscola, IL, In our earlier studies,14,20 we have shown these particles to be amorphous and about 0.05 am in size, For coverage of these particles with H20 and C2H50H, the following procedure was employed. About 5 mg of silica was mixed with 50 mL of the liquid (H2O or C2H5OH) and refluxed for one hour, The remaining liquid was allowed to evap¬orate to dryness and 1 mg of the treated sample was used to collect the PA spectra. In the case of PVPNO, the amount that binds to Cab-O-Sil is taken from the data on quar"

Mar 1, 1992

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to to7 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By J. Sjöberg, P. Lundman, E. Nordlund, C. Quinteiro

Abstract In the Kiirunavaara underground mine, crude ore is transported through ore passes from the production levels to the main haulage level. Failure and stability problems have occurred in some of these ore passes, with increasing frequency as mining depths increase. In this paper, selected results are presented from a research project run by LKAB. The presentation focuses specifically on stability analysis. Numerical models were used to identify failure mechanisms, in conjunction with empirical data and engineering judgment. The most important controlling factors governing failure and damage in ore passes were quantified. A causative model was established in which failure mechanisms and failure development were described. This model was used to formulate a prognosis of future ore pass stability, and for recommending remedial measures. Résumé Le transport du minerai entre les niveaux de production et le niveau principal de transport, à la mine de fer de Kiruna, se fait par des passes à minerai. Avec la profondeur d'extraction grandissante, les problèmes de stabilité au niveau de ces passes à minerai se sont multipliés. Les résultats d'un programme de recherche sur la stabilité des passes à minerai à la mine de fer de Kiruna sont présentés dans cet article. Les mécanismes de rupture ont été identifiés à l'aide de modèles numériques, de données de terrain et du jugement empirique des ingénieurs. Les facteurs principaux controllant l'instabilité des passes à minerai ont aussi été quantifiés. Un modèle a été établi dans lequel les mécanismes de rupture et le développement des dommages ont été décrits. Ce modèle a été utilisé à fins prédictives et remédiatives. Zusammenfassung In der Grube Kiirunavaara wird das gewonnene Erz über Sturzschächte von den Abbauebenen zu der Hauptförderebene gefördert. Mit zunehmender Tiefe des Abbaus sind vermehrt Standsicherheitsprobleme in den Sturzschächten aufgetreten, die teilweise zu Verbrüchen geführt haben. In dem vorliegenden Beitrag werden ausgewählte Ergebnisse einer Forschungsarbeit des LKAB präsentiert. Dabei wird der Schwerpunkt auf die Standsicherheitsuntersuchungen gelegt. Zur Ermittlung der Bruchmechanismen wurden numerische Modelle in Verbindung mit empirischen Daten angewendet. Die wichtigsten Einflußfaktoren für das Versagen der Sturzschächte wurden ermittelt. Es wurde ein Modell zur Beschreibung der Bruchmechanismen und des Versagensablaufs aufgestellt. Dieses Modell wurde verwendet, um die Standsicherheit zukünftiger Sturzschächte zu prognostizieren und um Sanierungsmaßnahmen zu erarbeiten.

Jan 1, 2003

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002