Search Documents

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By R. J. Traill

Introduction Following the discovery of high-grade deposits of pitchblende in the Great Bear Lake area of the Northwest Territories by Mr. Gilbert LaBine in May, 1930, samples were submitted to the Mines Branch for examination and investigation as to suitable methods of treatment (1). The purpose of this paper is to present, briefly, the results of the investigative work conducted on the ores and an outline of the methods developed for the extraction of the radium content and recovery of the by-products. The paper is presented in two parts. Part I gives a review of the history of radium production and of the principal processes used in other countries. Part II describes the work and gives the results of the Mines Branch investigation. Part 1-Radium Production In Other Countries Historical Outline Uranium was discovered in 1789, and more than a century later Madame Curie, while studying the physical properties of this element, observed that the ore of uranium exhibited greater activity than the pure uranium com-pounds she had prepared and traced the cause to the presence of a new element which she named radium. Eventually, research proved radium to be a disintegration product of uranium, and always present in uranium ores.

Jan 1, 1933

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

By M. Akser

Ilmenite, rutile, and zircon deposits of commercial importance have not been reported to-date from Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit along the Black Sea coast of Turkey in the vicinity of Ormanli, northwest of Istanbul. Consequently beach and sand dune samples were collected from that area for additional analysis. Laboratory methodologies, designed to simulate standard industrial heavy-mineral plant practices, were used to analyze and evaluate the samples. Based on the analyses, and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1995

By Rick Sarkisian, Greg Girardey, David Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 "Welded Steel Conveyor Pulleys" adequately defines pulley assembly standards for light material handling applications. However, most mining applications demand pulleys of higher reliability and load capacity than that offered by CEMA standard pulleys. Various sources have published specifications for "Engineered" conveyor pulleys. Typically, these specifications require T-section type pulleys applicable to operating belt tensions exceeding 439 N/mm (2,500 lb./in.). This paper examines the application of CEMA standard pulleys, T-section pulleys and also a mining duty pulley design. The mining duty pulley fills the void between CEMA standard pulleys and T-section pulleys and can eliminate the high cost and long lead times associated with T-section type pulleys.

Jan 1, 1998

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the 'resistivity map of the subsoil' in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By Franc R. Joubin, Donald H. James

"The Property of Rix Athabasca Uranium Mines Limited is in the Beaverlodge area of northwestern Saskatchewan. The mine is 7 miles by road north from the Lake Athabasca port of Bushell which is 250 miles north by aircraft or boat from railhead at Waterways, Alberta.The Rix property is a portion of the former DD 1 concession, obtained in 1949 from the government of Saskatchewan when private prospecting for uranium became permissible. The concession was prospected in detail during the 1950 and 1951 field seasons and a great many radioactive show-ings were discovered. Development and drilling were concentrated in two and later three of these areas, and by late 1952 enough ore had been indicated in the Leonard series and ""Smitty"" zone to justify underground development by adit-drift and shaft respectively.Four hundred feet of drift development on the Leonard No. 1 vein and the sinking of a two-level vertical shaft with related lateral development on the Smitty zone were completed in 1953. In April 1954 the Smitty section was placed in production at a rate averaging 100 tons per day, thereupon becoming the first privately owned post-war uranium producer in Canada. The ore is shipped for processing 12 miles by truck to the mill of Eldorado Mining and Refining Limited.Until recently all of the Company's production was drawn from the Smitty orebody. In April, 1955, ore production commenced from the faulted west extension of the Smitty structure, known as the Rix 62 zone, and from the Leonard No. 1 vein.The Smitty orebody (see Figure 2) is an intensely brecciated lenticular zone bordering both sides of the Smitty fault. The breccia areas are irregularly mineralized with pitchblende, very sparse galena, and pyrite in a gangue of feldspar, chlorite, calcite, and silica, all thoroughly soaked with fine-grained hematite to produce the locally-called ""red alteration"".Tenor of the ore currently being mined is classified information. The average grade estimated, prior to production, was 0.20 per cent (4.0 lbs.) U308 per ton."

Jan 1, 1949

By N. A. Gokcen

This Bureau of Mines report reviews and summarizes recent studies of the rates of chlorination of aluminous resources with CO and C12 mixtures with and without COC12. No reaction mechanism could be obtained from the existing results; however, diffusional barriers in the gas and solid layers probably control the chlorination rate in thermogravimetric experiments. Fluidized beds of particles smaller than 0.1 mm appeared to show very little solid layer diffusional barrier. For optimum chlorination the particle size should probably be less than 8 mm, the calcination temperature approximately 700° C, and the chlorination temperature from 650° to 750° C. Relatively rapid chlorination with COC12 in thermogravimetric experiments was attributed partly to the simultaneous supply of reductant and chlorinator by one gas to the sample reaction site. Comparable results for chlorination of fluidized beds with COC12 are not available. Equimolar mixtures of CO and C12 produced the optimum rate of reaction. Addition to the calcine of 10 to 20 wt-pct NaCl accelerated the rate of chlorination, and addition of SiC14 to the gas mixture decreased the rate of chlorination of SiO2 drastically, but at the expense of chlorination of significant fractions of Al2O3. Further research in various areas is suggested.

Jan 1, 1983

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Philippe Henry

"Hydrometal provides an adequate technology to reintroduce otherwise lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies at an integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed: (I) Residual low quality acid and caustic are used in the processing of zinc industry cements to produce copper, nickel, cobalt and zinc concentrates by several consecutive selective leach - precipitation processes.(II) Copper anode slimes are treated and their precious metal contents are recovered. Depending on the composition of the slimes, separate or combined concentrates of copper, bismuth, tellurium/selenium and silver/precious metals can be produced."

Jan 1, 2008

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By C. M. Romanowitz

This report deals with the factors which should be considered in evaluating a placer deposit and selecting a dredging system for mineral recovery. Overall dredging feasibility and the design of dredging systems are reviewed. Excavation methods, each with its advantages and disadvantages, are compared. Direct operating costs, both original and updated, of gold dredges with bucket capacities of 6 to 18 cubic feet are included. Costs vary with digging depth, changes in environmental conditions, and physical characteristics of the placer, all of which affect excavation rate and recovery. The costs, updated with appropriate indexes, should be used only as guidelines to evaluate potential dredging projects with similar characteristics. The relation of direct dredging costs to annual production is graphically illustrated by a family of curved envelopes that span dredge sizes from 2-112 to 18 cubic feet. A curve fitted to the data expresses the relation of direct costs to annual production for 151 dredge-years.

Jan 1, 1970

By Enrique Monge

Dado que a nivel universitario existen pocos laboratorios adecuados de Física y Química en el Perú, se ha desarrollado proyectos de laboratorios privados y plantas experimentales tanto en el campo analítico y metalúrgico que encauzen la industria minera por el sendero de la técnica más elemental. En ese sentido, el presente texto señala la importancia de los laboratorios de investigación para las industrias mineras y metalúrgicas a través de la Universidad Nacional de Ingeniería y el apoyo del Estado. El laboratorio está dividido en 6 secciones: Minería, preparación y concentración de minerales; metalurgia de minerales no Ferrosos; carbón; fierro y acero; metales y aleaciones.

Jan 1, 1959

INCREASE OF CATASTROPHE FREQUENCY AND SEVERITYIn the last couple of decades the frequency of natural catastrophes has increased dramatically. This realization results from the statistical analysis of the comprehensive loss data that we have been collecting constantly over the last 30 years and have evaluated in connec-tion with the preparation of our "World Map of Natural Hazards", which is now in its second edition (Munich Re, 1988). Each month brings data on between 30 and 50 new loss events. Fortunately, however, only a few of these have to be added to the list of major natural catastrophes, that is only those involv-ing damage that considerably exceeds what the country or region concerned can handle itself so that substantial na-tional or international aid is required. That is generally the case if the number of dead runs into the hundreds or thousands, if tens or hundreds of thousands of people are rendered home-less and if the total economic loss is in the region of US$ 100 million. These major catastrophes, about which we have fairly comprehensive data even in the case of those that occurred farther back in the past, numbered only 14 in the 1960s but 70 in the 1980s; they there-fore increased over a period of 30 years by a factor of 5. The trend is also very clear when we consider the total economic loss, which - adjusted for in-flation - increased during the same period from an average of US$ 3.7 bil-lion per year to US$ 11.4 billion, i.e. by a factor of 3.1. The insured losses, finally, increased by as much as a fac-tor of 4.8.

Jan 1, 1990

By Georg Petersen

El presente texto describe la historia del primer centenario de la industria petrolera peruana (1863 -1963). La revisión va desde la historia temprana del petróleo en la primera mitad del siglo XIX, desarrollo de la industria moderna del petróleo en el Perú hasta el estado actual de este.

Jan 1, 1964

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015