Search Documents

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By Wern-ping (Nick) Chen

The Florida Department of Transportation District 6 (FDOT D6) began a study in 1987 for a master plan to improve the traffic circulation and congestions between the Port of Miami (POM) and downtown Miami, FL. This study included a tunnel connection between two man-made islands, the Watson and the Dodge islands. Though a finding of no significant impact (FONSI) was completed in 1992, the project remained on hold for about 10 years. In 2002, Florida Turnpike took over this project, re-evaluated its benefits to the lo-cal communities, determined its feasibility (specifically the tunnel options) and established a probable cost. In 2005, the FDOT D6 regained its charge over the project and concluded that a bored tunnel under Biscayne Bay is feasible. Its primary components are: ? Widening of the MacArthur Causeway Bridge, to accommodate truck traffic to the Port of Miami. ? A tunnel connection between Watson Island and Dodge Island, where the POM is located. ? Connections to the POM roadway system, either for the traffic from the city of Miami or for the truck traffic from I-395 to the POM. The project will improve access to and from the POM and provide a dedicated roadway connector linking the POM with the MacArthur Causeway (State Route 41/1) and I-395, specifically for the trucks in and out of the POM without going through downtown Miami. As identified in the project information memorandum (PIM), its primary objectives are to: ? Improve access to the POM, helping to keep it competitive and ensuring its ability to handle projected growth in its cruise and cargo operations. [ ] ? Improve traffic safety in downtown Miami by removing POM traffic, trucks and buses from the congested downtown street network and, in doing so, facilitate ongoing and future development plans in and around downtown Miami.

Jan 1, 2009

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By V. I. Ryaboy, V. A. Luknitsky, V. V. Zuyev

The action has been studied of three types of reagents used as intensifiers in grinding copper-molybdenum, sulphide-sheelite, polymetallic and other types of ores, namely N-donor, dispersant, and surface-acting agents. It has been proved that, depending on the type of ore treated, the C (N-donor) and C-170 (dispersant) reagents increase the yield of the principal size fraction of 0.074mm by 8-16% (relative). Consequently, the specific mill capacity improves by 13-21 %. The C and C-170 reagents activate the subsequent flotation stage and are thus beneficial to the mineral recovery. The surface-acting reagents affect the mineral grinding process to a lesser extent. The intensifying action of the reagents is attributed to the effective crushing energy decrease (lower crack-resistance factor) or else to the slime-dispersing effect of the reagents. The pilot-plant test results for the C reagents are given. Both C and C170 reagents are commercially produced and recommended for use at a number of concentrators in Russia, Uzbekistan and Kazakhstan.

Jan 1, 1995

By M Berry

Consider these four questions:What is the definition of life-of-mine?When should life-of-mine planning seriously commence?When can life-of-mine planning seriously commence?What is the key input to effective life-of-mine planning?Whilst there is likely to be general consensus on the answers to the first three questions, the answer to the fourth question is open to debate. This author argues that understanding and managing risks and opportunities associated with geological uncertainty is the key input to effective life-of-mine planning, at all stages in the life cycle of a mining project.CITATION:Berry, M, ?2014. Effective life-of-mine planning by understanding and managing risks and opportunities associated with geological uncertainty, in Proceedings Life-of-Mine 2014 , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By Marcial Medina

El presente texto describe la reología de la Pulpa a nivel de química de superficie y así sugerir las alternativas a los problemas que impiden poder operar en forma continua y su capacidad de diseño la Planta de Flotación Diferencial de Cobre – Molibdeno. Asimismo, es necesario definir una solución a escala de laboratorio, la cual debe ser validada con pruebas industriales e implementarla en planta. La estrategia debe garantizar la continuidad de la operación de la Planta de flotación de Molibdeno con cualquier tipo de mineral y que no presente compactación la pulpa. Finalmente, se devbe agarantizar el procesamiento de toda la producción de la planta de cobre en la planta de flotación diferencial de cobre molibdeno.

Sep 12, 2011

By W. H. Howard

As the result of a series of analyses and volume determinations of gases discharged from the converters at the Garfield Smelting Co.'s. smelter at Garfield, Utah, it was found that a considerable amount of lead fume was escaping from the stacks of the converter plant, and `that if this lead could be recovered at a reasonable expense an attempt should be made to collect it. Two methods suggested themselves: (1) filtration through bags; (2) electrical precipitation of the condensed fume by a Cottrell plant. Filtration through Bags Tests were made in filtering converter gases through the ordinary woolen bags of lead-smelter bag houses to determine how long such material could withstand the corrosive action of the gases. While blowing on white metal only, the fabric was usually destroyed in 10 to 14 hr. In tests conducted in filtering gases when blowing on matte or slagging stage exclusively and when relatively considerable lead was being volatilized, bags in one instance lasted 60.5 hr. It therefore was evident that the Garfield converter gases did not contain in themselves sufficient neutralizing elements for the purpose of direct bag filtration, even during the slagging stage. Such results were more or less anticipated, but it was thus proved that under all conditions of blowing Garfield mattes a very considerable amount of neutralizing agent, zinc oxide or lime, or both combined, as in the Sprague process, would be required to render bag filtration possible. Again, owing to the constantly changing quantities of SO3 from a given battery of converters, depending on the number blowing at a given time and on the stages of the blow, it would be practically impossible to feed automatically the required amount of neutralizer. In order to safeguard the bags sufficient neutralizer would have to be continuously added to meet the maximum SO3 output, thus. wasting neutralizers and giving an undesirably diluted final product. Such a condition is entirely different

Jan 8, 1914

By John L. Halls

INTRODUCTION In this section, it is assumed that the reader is an engineer with sufficient training in underground mining work, preferably with budgetary control, to understand the mining methods outlined in other sections of this handbook. The mining-method descriptions are not repeated herein; only sufficient information is provided to enable the reader to comprehend the development of the costs presented. All costs are in 1977 US dollars, except where explicitly stated otherwise. CAPITAL INVESTMENT The capital investment in the underground mining portion of any mining property includes the following: 1) The development of original access involving adits, shafts, declines, etc. It includes the necessary equipment for transporting men, materials, and rock. 2) The purchase of mine equipment including loaders, underground haulage equipment, fans, pumps, electrical distribution, surface facilities associated with the underground mine, etc. 3) Sufficient preproduction mine development to assure steadily increasing production after startup. De- pending upon the mining method used, the preproduction development should provide a supply of three months to one year of ore that is developed and is ready to be stoped. Underground development also includes excavations other than shaft stations, loading pockets, sumps, etc., which usually are associated with the means of access and are excavated by the contractor. These excavations could include a crusher cavern, an ore- storage pocket, and underground workshops that may or may not be included by the shaft-sinking contractor. Portions of these could be delayed until after production begins, but it is preferable to complete them during the development phase, so there is no interference with the production buildup. 4) The staff and labor costs for all phases from inception through final production. 5) The provision of mine-surface equipment and facilities strictly applicable to the underground portion of the operation. The required facilities include a changehouse with a lamp room, a first-aid station, compressors, an electrical substation, workshops, a ware- house, water pipelines to the concentrator, water storage tanks, explosive storage, etc. A concrete-batch plant, a sand-fill plant, and boilers for heating may be required. 6) Other direct and indirect costs. 7) Engineering, design, and procurement costs. 8) Contingency allocations. 9) Contractor's fees, startup costs, and owner's costs. Original Access As part of a study for the US Bureau of Mines, Dravo Corp. conducted an extensive literature research survey covering underground operations in the United States between 1963 and 1973. Table 1 is compiled from the section of that study pertaining to the types of access to underground mines. Table 1 does not include distances attributable to the deepening of existing shafts, nor does it include shafts bored by raise drills or downhole machines that need existing underground workings for the disposal of the cuttings. During the period under review in the report ( 1963 through 1973). concrete-lined circular vertical shafts were the predominant means of providing the first access to a new underground mine; these shafts accounted for 80% of the original access in terms of the number of accesses completed, and 75% in terms of the total verti- cal linear distances. The inside diameters of the conventional circular shafts ranged from 3.7 to 7.0 m (12 to 23 ft). Most (72% ) of these conventional shafts were for production,

Jan 1, 1982

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By A. E. Nehrenberg

R. A. Schmucker, Jr.—The writer wishes to point out that an acicular growth of austenite, similar to that described in the author's paper, was recently observed in an alloy steel of only 0.06 C content. This steel, which represents an 0.07 max C, 1.35 Cr, 0.55 Ni, 0.20 Mo analysis, combines the characteristics of minimum hardness in the annealed condition with maximum hardenability and is therefore suited primarily for cold-hobbing applications. The acicular austenite formation in this steel was observed accidentally during a determination of its Ac1 temperature. The samples used in this investigation represented as-forged bar stock which had been given a preliminary temper at 1300°F. The critical (Ac1) temperature was finally established at 1400 °F. Fig. 15 represents the microstructure of the sample which had been heated at 1450°F for ½ hr, water quenched, and tempered at 600°F for ½ hr (for the purpose of darkening the martensite). It will be observed from the distribution of the darkened areas of martensite that the parent austenite grains formed at 1450°F had grown in an acicular manner and still occupied only a small percentage of the total area. The remainder of the area contains the original equiaxed ferrite grains in which new austenite had as yet scarcely formed. However, the tiny isolated martensitic patches at several points where three or more ferrite grains intersect indicate that small austenite grains had formed and started to grow in an apparently equiaxed fashion. Fig. 16 represents the prior microstructure of an original sample in the as-forged and tempered condition, before it was heated -above the critical temperature. It is probable that there are two kinds of ferrite in this structure: (1) The equiaxed proeutectoid ferrite grains which separated from the austenite when the steel was cooled from the forging temperature, and (2) the acicular ferrite associated with the aggregate of fine carbide which is represented by the patches of

Jan 1, 1951

The material presented in this paper describes experimental work to determine the effect of variations in suction nozzle design upon inlet flow conditions. Four entrance profile shapes were examined under controlled conditions of slurry flow and it was found that the straight ended nozzles had consistently higher entrance losses than the straight taper or the ellipse, and that the circular arc profile nozzles were the most efficient. Subordinate considerations were the measurement of the quantities and the forces involved.As the work progressed, three distinct phases in the pattern of flow were apparent and the static pressures in each were carefully examined. An inlet zone was found to be unstable in changing boundary conditions, a transition zone was largely independent of slurry density and in a zone of stability the pressures were found to be directly related to the characteristics of the flowing pulp. In this zone pressure measurements were reproducible within ± 2 per cent regardless of changing boundary conditions.The effect of varying the "1" parameter of nozzles with a part circular entrance profile was examined and it was found that flow conditions approaching the ideal were obtained when the radius of curvature was between 0·40 and 0·550.

Jan 1, 1966

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

The bromine review did not arrive in time for publication in the June issue. Bromine production in the United States during 1992 amounted to 171 kt (376 million lbs), a 453-t (I-million lb) increase from 1991. Data compiled by the US Bureau of Mines indicates this increase was due mainly to greater exports of elemental bromine and bromine derivatives (flame retardants). Exports increased despite the economic slowdown in Europe and Japan. The United States remains the world's largest bromine producer, with about 42% of the total. Israel is ranked second, followed by the United Kingdom, the former Soviet Union and Japan.

Jan 1, 1993

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985